Hallo, ich habe für meinen Lubuntu-PC an meinem Router über Einstellungen/ Netzwerkverbindungen eine statische IPV4-Verbindung eingerichtet. Der IN-Browserzugriff klappt problemlos. Allerdings kann ich keine neue Software (Libre Office Calc) vom Lubuntu-Softwarecenter runterladen. Fehler: failed to fetch http://security.ubuntu.com/.... Kann das damit zusammenhängen, dass ich keine IPV6-Verbindung eingerichtet habe? Ist das erforderlich? Gruss wonkwonk
Netzwerkzugang IPV6
Anmeldungsdatum: Beiträge: Zähle... |
|
Anmeldungsdatum: Beiträge: 15837 |
Hallo wonkwonk, IP6 ist nicht erforderlich ...... Ausgabe im Codeblock von Ping an eine Internetadresse wäre hilfreich. Gruss Lidux |
(Themenstarter)
Anmeldungsdatum: Beiträge: 84 |
Hallo, leider weiß ich nicht, wie ich die ping-Ausgabe kopieren soll. Ein ping auf heise.de liefert: ttl=246 time jeweils etwa 31ms, kein paket loss Sonst wüßte ich nicht, was Du mit Codeblock meinst. Gruss wonkwonk |
Anmeldungsdatum: Beiträge: 15837 |
Hallo wonkwonk, Somit besteht eine Verbindung zum Internet. Geht es hier um WLAN oder LAN ? Ansonsten bitte dies beachten: http://forum.ubuntuusers.de/topic/vor-dem-erstellen-eines-neuen-beitrags-bitte-/ Codeblock sieht so aus: Information zur Ausagabe ... Gruss Lidux |
(Themenstarter)
Anmeldungsdatum: Beiträge: 84 |
Hallo, es ist ein LAN, angebunden über separaten Switch und Router. Ich weiß leider immer noch nicht, was Du als Codeblock erwartest. Die Ausgabe Information zur Ausgabe ... tritt bei mir beim Ping-Befehl nicht auf. ping -c 2 $(route -n | grep UG | awk {'print $2'}) wird bei mir nicht akzeptiert (ich habe die Zeile wirklich korrekt abgeschrieben). Gruss wonkwonk |
Supporter
Anmeldungsdatum: Beiträge: 22096 Wohnort: ~ |
Offenbar keine Verbindung zum Router möglich. Zeige alle Terminal-Ausgaben von hier in Codeblöcken zur "Diagnose". Gruss praseodym |
(Themenstarter)
Anmeldungsdatum: Beiträge: 84 |
Hallo, dann will ich mal versuchen, die umfangreichen Ausgabe in das posting zu bekommen uname: Linux Luwo 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux cat Ausgaben: # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback Befehl cat /etc/resolv.conf wird nicht gefunden. 127.0.0.1 localhost 127.0.1.1 Luwo # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters 192.168.1.6 Luwo ifconfig: eth0 Link encap:Ethernet Hardware Adresse 00:17:31:67:86:d0 inet Adresse:192.168.1.6 Bcast:192.168.1.255 Maske:255.255.255.0 inet6-Adresse: fe80::217:31ff:fe67:86d0/64 Gültigkeitsbereich:Verbindung UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1 RX-Pakete:4078 Fehler:0 Verloren:0 Überläufe:0 Fenster:0 TX-Pakete:3500 Fehler:0 Verloren:0 Überläufe:0 Träger:0 Kollisionen:0 Sendewarteschlangenlänge:1000 RX-Bytes:3203350 (3.2 MB) TX-Bytes:397019 (397.0 KB) lo Link encap:Lokale Schleife inet Adresse:127.0.0.1 Maske:255.0.0.0 inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine UP LOOPBACK RUNNING MTU:65536 Metrik:1 RX-Pakete:860 Fehler:0 Verloren:0 Überläufe:0 Fenster:0 TX-Pakete:860 Fehler:0 Verloren:0 Überläufe:0 Träger:0 Kollisionen:0 Sendewarteschlangenlänge:0 RX-Bytes:85327 (85.3 KB) TX-Bytes:85327 (85.3 KB) kein WLAN route Kernel-IP-Routentabelle Ziel Router Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 NetworkManger: [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true
[main] plugins=ifupdown,keyfile,ofono dns=dnsmasq no-auto-default=00:17:31:67:86:D0, [ifupdown] managed=false Schnittstellen: # PCI device 0x10de:0x0373 (forcedeth) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:17:31:67:86:d0", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" Der erste ping-Befehl wird nicht erkannt, die anderen ok. Die Abfrage des Logauszugs ergibt keine Ausgabe. Fehlermeldungen: [ 0.685807] audit: initializing netlink socket (disabled) [ 0.928336] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64. [ 1.452563] forcedeth 0000:00:08.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:17:31:67:86:d0 [ 1.452566] forcedeth 0000:00:08.0: highdma csum vlan pwrctl mgmt gbit lnktim msi desc-v3 [ 17.872750] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 25.449026] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 29.833958] forcedeth 0000:00:08.0: irq 45 for MSI/MSI-X [ 29.834001] forcedeth 0000:00:08.0 eth0: MSI enabled [ 469.463794] Modules linked in: bnep rfcomm bluetooth tda1004x saa7134_dvb videobuf_dvb saa7134_alsa dvb_core snd_hda_codec_analog joydev tda827x snd_hda_intel snd_hda_codec snd_hwdep snd_$ [ 469.632085] Modules linked in: bnep rfcomm bluetooth tda1004x saa7134_dvb videobuf_dvb saa7134_alsa dvb_core snd_hda_codec_analog joydev tda827x snd_hda_intel snd_hda_codec snd_hwdep snd_$ [ 470.048808] forcedeth 0000:00:08.0: irq 45 for MSI/MSI-X [ 470.048847] forcedeth 0000:00:08.0 eth0: MSI enabled [ 470.049061] forcedeth 0000:00:08.0 eth0: no link during initialization [ 471.717132] forcedeth 0000:00:08.0 eth0: link up [ 472.108756] forcedeth 0000:00:08.0: no hotplug settings from platform [ 472.108758] forcedeth 0000:00:08.0: using default PCI settings [ 1639.483870] Modules linked in: bnep rfcomm bluetooth tda1004x saa7134_dvb videobuf_dvb saa7134_alsa dvb_core snd_hda_codec_analog joydev tda827x snd_hda_intel snd_hda_codec snd_hwdep snd_$ [ 1640.063533] forcedeth 0000:00:08.0: irq 45 for MSI/MSI-X [ 1640.063571] forcedeth 0000:00:08.0 eth0: MSI enabled [ 1640.063785] forcedeth 0000:00:08.0 eth0: no link during initialization [ 1642.144708] forcedeth 0000:00:08.0: no hotplug settings from platform [ 1642.144710] forcedeth 0000:00:08.0: using default PCI settings [ 1646.004237] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 1764.363779] Modules linked in: bnep rfcomm bluetooth tda1004x saa7134_dvb videobuf_dvb saa7134_alsa dvb_core snd_hda_codec_analog joydev tda827x snd_hda_intel snd_hda_codec snd_hwdep snd_$ [ 1764.948634] forcedeth 0000:00:08.0: irq 45 for MSI/MSI-X [ 1764.948673] forcedeth 0000:00:08.0 eth0: MSI enabled [ 1764.948887] forcedeth 0000:00:08.0 eth0: no link during initialization [ 1766.616621] forcedeth 0000:00:08.0 eth0: link up [ 1766.617026] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 1767.024693] forcedeth 0000:00:08.0: no hotplug settings from platform [ 1767.024695] forcedeth 0000:00:08.0: using default PCI settings So, ich hoffe, das hilft weiter. Vielen Dnak für die Mühe. Gruss wonkwonk |
Anmeldungsdatum: Beiträge: 15837 |
Hallo wonkwonk, Alles klar, eine "forcedeth" Lan Chipsatz. Der müssen einige Parameter mitgegeben werden damit diese funktioniert. Entweder ins WIKI schauen oder warten bis praseodym dir den Befehl gibt. Gruss Lidux |
Supporter
Anmeldungsdatum: Beiträge: 22096 Wohnort: ~ |
echo "options forcedeth msi=0 msix=0" | sudo tee /etc/modprobe.d/forcedeth.conf sudo modprobe -rfv forcedeth sudo modprobe -v forcedeth sind die Parameter |
(Themenstarter)
Anmeldungsdatum: Beiträge: 84 |
Super, das hat es gebracht, der Software-Download läuft jetzt problemlos. Es ist mir zwar schleierhaft, wieso der Browserzugriff auch schon vorher ging und der Rest nicht, aber ich muss ja auch nicht alles wissen 😉 Vielen Dank, Gruß wonkwonk |
Anmeldungsdatum: Beiträge: 15837 |
Hallo wonkwonk, Dann Thread bitte auf gelöst setzen. (Portalregel) Gruss Lidux |