Hallo,
gemäß Lm sensors habe ich mit "sensors-detect" gearbeitet:
$ sudo sensors-detect # sensors-detect revision 6170 (2013-05-20 21:25:22 +0200) # Board: ASUSTeK COMPUTER INC. M5A97 PRO [... hier viel ausgelassen ...] Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `fam15h_power' (autoloaded): * Chip `AMD Family 15h power sensors' (confidence: 9) Driver `k10temp' (autoloaded): * Chip `AMD Family 15h thermal sensors' (confidence: 9) Driver `it87': * ISA bus, address 0x290 Chip `ITE IT8721F/IT8758E Super IO Sensors' (confidence: 9) To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers it87 #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO)yes Successful! Monitoring programs won't work until the needed modules are loaded. You may want to run 'service kmod start' to load them. Unloading i2c-dev... OK Unloading cpuid... OK $ sudo service kmod start kmod stop/waiting
Ein folgendes "sensors" ergibt viel ALARM und unverständliche Werte:
$ sensors k10temp-pci-00c3 Adapter: PCI adapter temp1: +8.0°C (high = +70.0°C) (crit = +90.0°C, hyst = +87.0°C) it8721-isa-0290 Adapter: ISA adapter in0: +2.80 V (min = +0.06 V, max = +0.92 V) ALARM in1: +2.87 V (min = +2.15 V, max = +2.42 V) ALARM in2: +0.89 V (min = +1.66 V, max = +1.44 V) ALARM +3.3V: +3.26 V (min = +5.98 V, max = +0.86 V) ALARM in4: +0.17 V (min = +0.06 V, max = +2.64 V) in5: +2.47 V (min = +0.05 V, max = +2.83 V) in6: +0.96 V (min = +2.88 V, max = +2.40 V) ALARM 3VSB: +5.42 V (min = +2.57 V, max = +4.27 V) ALARM Vbat: +3.34 V fan1: 1214 RPM (min = 18 RPM) fan2: 0 RPM (min = 32 RPM) ALARM fan3: 0 RPM (min = 61 RPM) ALARM temp1: +28.0°C (low = -120.0°C, high = -96.0°C) ALARM sensor = thermistor temp2: +29.0°C (low = +99.0°C, high = -59.0°C) ALARM sensor = thermistor temp3: -128.0°C (low = -55.0°C, high = +16.0°C) sensor = disabled intrusion0: OK fam15h_power-pci-00c4 Adapter: PCI adapter power1: 32.83 W (crit = 125.19 W)
In der /etc/sensors3.conf steht
chip "it87-*" "it8712-*" "it8716-*" "it8718-*" "it8720-*" label in8 "Vbat"
das passt nicht wirklich auf IT8721F/IT8758E, eine /etc/sensors.conf gibt es nicht.
Ein bischen Suchen nach M5A97 & IT8721F brachte mich zu lm-sensors.org, wo empfohlen wird:
chip "k10temp-pci-00c3" label temp1 "CPU Temp (rel)" chip "it8721-*" label in0 "+12V" label in1 "+5V" label in2 "Vcore" ignore in4 ignore in5 ignore in6 compute in0 @ * (515/120), @ / (515/120) compute in1 @ * (215/120), @ / (215/120) ignore temp3 label temp1 "CPU Temp" label temp2 "M/B Temp" label fan1 "CPU Fan" label fan2 "Chassis Fan" label fan3 "Power Fan" ignore intrusion0
in die /etc/sensors3.conf zu schreiben.
Darf man diesen Vorschlägen folgen? Muss man da noch irgendwas prüfen? Macht das Sinn? Auch in Bezug auf eine eventuell spätere Nutzung von fancontrol wie in Lüftersteuerung?