Bong_Ra
(Themenstarter)
Anmeldungsdatum: 23. August 2014
Beiträge: 58
|
| # /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
# Parameters can be specified after the module name.
lp
rtc
parport_pc
|
Ich mach mal ne Pause und schau heute abend noch mal rein. Vielen Dank erstmal für die ausführliche Hilfe. Beste Grüße
|
Tuemmler
Anmeldungsdatum: 26. März 2007
Beiträge: 8020
Wohnort: Süsel / Ostholstein
|
OK, die Karte wird scheinbar schon vom Rechner nicht erkannt. Stellt sich die Frage warum? Bitte noch einmal Hardwareseitig prüfen. Gruß Nachtrag: Führen wir einen Check durch ▶ http://kmuto.jp/debian/hcl/ 2. Nachtrag: Beachte bitte den Unterschied Serielle_Schnittstelle und Parallele_Schnittstelle
|
Bong_Ra
(Themenstarter)
Anmeldungsdatum: 23. August 2014
Beiträge: 58
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20 | PCI ID Funktioniert? Hersteller Device Treiber kernel
80860150 Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor DRAM Controller
80860152 Ja Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor Graphics Controller i915 v3.0.0-
80861c3a Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1
80861c2d Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2
80861c20 Ja Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller snd-hda-intel
80861c10 Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1
80861c14 Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3
80861c16 Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4
80861c18 Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5
80861c1a Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6
80861c26 Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1
80861c5c Ja Intel Corporation H61 Express Chipset Family LPC Controller iTCO_wdt
80861c00 Ja Intel Corporation 6 Series/C200 Series Chipset Family 4 port SATA IDE Controller ata_piix
80861c22 Ja Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller i2c-i801
80861c08 Ja Intel Corporation 6 Series/C200 Series Chipset Family 2 port SATA IDE Controller ata_piix
1b6f7023 Etron Technology, Inc. EJ168 USB 3.0 Host Controller
1b4b917a Ja Marvell Technology Group Ltd. 88SE9172 SATA III 6Gb/s RAID Controller ahci
10ec8168 Ja Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller r8169
1c003050
|
|
Tuemmler
Anmeldungsdatum: 26. März 2007
Beiträge: 8020
Wohnort: Süsel / Ostholstein
|
Moin Moin, sieht so aus, als wenn die Karte überhaupt nicht unterstützt wird. Wenn ich richtig liege, dürfte es sich gem. [user:Bong Ra:] [post:7359868: schrieb]:
> {{{#!code text
> x@x:~$ lspci
> 05:00.0 Serial controller: Device 1c00:3050 (rev 10)
> x@x:~$ um diese Karte handeln. In der Prüfung erscheint diese gar nicht erst. Google sagt ▶ https://www.google.de/#q=Serial+controller:+Device+1c00:3050+%28rev+10%29 Da es sich in Deinem Fall um eine PCIe handelt befürchte ich, das klappt nicht. Einen letzten Versuch kannst du mit dieser Anweisung von Axt unternehmen ▶ 6149662 ersetze dabei die Einträge hplip/3.14.3 durch hplip/3.15.2 Gruß Und wieder ein Nachtrag: http://kent-vandervelden.blogspot.de/2014/08/linux-parallel-port-cards.html?_escaped_fragment_#!
|
Bong_Ra
(Themenstarter)
Anmeldungsdatum: 23. August 2014
Beiträge: 58
|
Hey,
die folgende Karte aus dem Link und meine Karte haben den selben Chipsatz (WCH382L Chipset SI-PEX10010): 1
2
3
4
5
6
7
8
9
10
11
12 | Iocrest SI-PEX10010 Failed
This board was sold as "Syba WCH382L Chipset SI-PEX10010" but Iocrest was the name on the box. Regardless, the same chipset is present and the same model number is used.
While this board failed to be recognized as a parallel port, there may be hope. However, an better solution is likely to avoid the card.
Output of dmesg
[ 0.183504] pci 0000:07:00.0: [1c00:3050] type 00 class 0x070005
[ 0.183526] pci 0000:07:00.0: reg 0x10: [io 0xcc00-0xccff]
[ 0.183542] pci 0000:07:00.0: reg 0x14: [mem 0xfbef8000-0xfbefffff pref]
[ 0.183559] pci 0000:07:00.0: reg 0x18: [io 0xcf00-0xcf03]
[ 0.183620] pci 0000:07:00.0: reg 0x30: [mem 0x00000000-0x00007fff pref]
[ 0.183702] pci 0000:07:00.0: PME# supported from D0 D3hot D3cold
|
|
While this board failed to be recognized as a parallel port, there may be hope. However, an better solution is likely to avoid the card.
|
Hier der Text, der unter "hope" verlinkt war.
http://www.spinics.net/lists/linux-serial/msg11744.html 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35 | Hi,
I have wch ch382 board which is mostly similar to already supported
ch353 I think. But 382 works in PCI-E slot whereas 353 in PCI.
I've written a patch and LPT looks working with
parport_serial. (Actually it works even using "modprobe parport_pc
io=0xe100")
But I have some problems with ttyS*.
Here are changes between CH353-2S1P and CH382-2S1P in vendor driver:
CH353 CH382
type 16550 16750
IntrBar 3 0
IntrOffset 0x0F 0xE9
ofs1 0,0 0xC0,0xC8
As I understand last line is offset to uart I/O ports, so I put 0xC0
to pci_parport_serial_boards[].first_offset and uart_offset is 8, so
/sys/class/tty/ttyS0/port is 0xE0C0
/sys/class/tty/ttyS1/port is 0xE0C8
and lspci -v reports "I/O ports at e000 [size=256]"
But I cannot find where should I put interrupt parameters IntrBar and
IntrOffset. Probably this is the reason why ttyS* don't work.
Here is vendor WCH driver:
https://home.p5n.pp.ru/~sergej/files/wch-driver.tar.gz
My patch is in attachment.
Attachment: wch-serial.diff
Description: Binary data
|
Ich würde versuchen, den Treiber + Patch zu installieren, um die Karte zum Laufen zu bekommen.
Allerdings habe ich vom Treiberinstallieren und "patchen" unter Linux überhaupt keine Ahnung.
Wie gehe ich da am besten vor?
|
Tuemmler
Anmeldungsdatum: 26. März 2007
Beiträge: 8020
Wohnort: Süsel / Ostholstein
|
Moin Moin, Du meinst aus diesem Link? http://kent-vandervelden.blogspot.de/2014/08/linux-parallel-port-cards.html?_escaped_fragment_#! Und siehe bitte die Markierung 😉
Iocrest SI-PEX10010 PCIe Failed WCH CH382L
Board also sold as
Syba WCH382L Chipset SI-PEX10010?
Bedeutet, sie funktioniert nicht, Ende / Aus.
und dann steht da noch:
However, an better solution is likely to avoid the card Was willst Du daran herumpatchen mit ungewissem Ausgang? Gruß Nachtrag: Bitte hier einmal lesen Parallel > USB Adapter ▶ http://wiki.ubuntuusers.de/Archiv/Hardwaredatenbank/Peripherie#Parallel-USB-Adapter
|
Bong_Ra
(Themenstarter)
Anmeldungsdatum: 23. August 2014
Beiträge: 58
|
| While this board failed to be recognized as a parallel port, there may be hope. However, an better solution is likely to avoid the card.
Output of dmesg
|
Die Aussage wurde durch einen Link untersterichen, der über "hope" zu der oben angegebenen Seite mit dem Link → Treiber + Patch führt.
Darauf habe ich mich bezogen.
|
Bong_Ra
(Themenstarter)
Anmeldungsdatum: 23. August 2014
Beiträge: 58
|
Ich würde versuchen, den Treiber + Patch zu installieren, um die Karte zum Laufen zu bekommen. Allerdings habe ich vom Treiberinstallieren und "patchen" unter Linux überhaupt keine Ahnung. Wie gehe ich da am besten vor?
Ist noch aktuell
|