ubuntuusers.de

Kein WLAN mit BCM 43225

Status: Gelöst | Ubuntu-Version: Ubuntu 10.10 (Maverick Meerkat)
Antworten |

Kuss_der_Diebe

(Themenstarter)

Anmeldungsdatum:
26. Juli 2008

Beiträge: Zähle...

Wohnort: Köln

Vielen Dank für deine Geduld. 👍

oliver@sommernachtswind:~$ sudo ip link set dev eth1 addr 00:1b:38:2c:6a:a5
[sudo] password for oliver: 
RTNETLINK answers: Too many open files in system
oliver@sommernachtswind:~$ ifconfig eth1
eth1      Link encap:Ethernet  HWaddr 00:1b:38:2c:6a:a5  
          inet6 addr: fe80::c646:19ff:fea6:8692/64 Scope:Link
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:404
          TX packets:0 errors:20 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:17 

Funktioniert hat´s leider trotzdem nicht.

elektronenblitz63

Avatar von elektronenblitz63

Anmeldungsdatum:
16. Januar 2007

Beiträge: 29307

Wohnort: NRW

Liegt anscheinend am Treiber. Alle Datenpakete gehen verloren, werden also weder gesendet, noch wird etwas empfangen:

          RX packets:0 errors:0 dropped:0 overruns:0 frame:404
          TX packets:0 errors:20 dropped:0 overruns:0 carrier:0

Kann der neue Rechner über Kabel an den alten Rechner mit bestehender Verbindung angeschlossen werden, so wie in Internetverbindungsfreigabe beschrieben? Dann wäre die Installation des aktuellen Broadcom-Treibers einfacher.

Kuss_der_Diebe

(Themenstarter)

Anmeldungsdatum:
26. Juli 2008

Beiträge: Zähle...

Wohnort: Köln

Ja, das funktioniert. Ging leichter, als ich dachte... 😉

elektronenblitz63

Avatar von elektronenblitz63

Anmeldungsdatum:
16. Januar 2007

Beiträge: 29307

Wohnort: NRW

Ja, das funktioniert. Ging leichter, als ich dachte...

Prima, dann deinstalliere zunächst den alten Systemtreiber

sudo modprobe -rf wl
sudo apt-get remove --purge bcmwl-kernel-source

Die Abfrage

modinfo wl

sollte dann keine brauchbare Ausgabe mehr erzeugen.

Den aktuellen Treiber installieren, 64bit-Version war ja richtig:

sudo apt-get install build-essential
mkdir Broadcom-STA64 && cd Broadcom-STA64
wget http://www.broadcom.com/docs/linux_sta/hybrid-portsrc_x86_64-v5_100_82_38.tar.gz
tar xvf hybrid-portsrc_x86_64-v5_100_82_38.tar.gz

Modul bauen und installieren:

make
sudo make install
sudo depmod -a
sudo modprobe wl
iwconfig

Alles fehlerfrei abgelaufen? Erneut testen und die Dasumen drücken.

Kuss_der_Diebe

(Themenstarter)

Anmeldungsdatum:
26. Juli 2008

Beiträge: 77

Wohnort: Köln

oliver@sommernachtswind:~/Broadcom-STA64$ make
KBUILD_NOPEDANTIC=1 make -C /lib/modules/`uname -r`/build M=`pwd`
make[1]: Entering directory `/usr/src/linux-headers-2.6.35-24-generic'
  LD      /home/oliver/Broadcom-STA64/built-in.o
  CC [M]  /home/oliver/Broadcom-STA64/src/shared/linux_osl.o
  CC [M]  /home/oliver/Broadcom-STA64/src/wl/sys/wl_linux.o
  CC [M]  /home/oliver/Broadcom-STA64/src/wl/sys/wl_iw.o
  LD [M]  /home/oliver/Broadcom-STA64/wl.o
  Building modules, stage 2.
  MODPOST 1 modules
WARNING: modpost: missing MODULE_LICENSE() in /home/oliver/Broadcom-STA64/wl.o
see include/linux/module.h for more information
  CC      /home/oliver/Broadcom-STA64/wl.mod.o
  LD [M]  /home/oliver/Broadcom-STA64/wl.ko
make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-24-generic'
oliver@sommernachtswind:~/Broadcom-STA64$ sudo make install
install -D -m 755 wl.ko /lib/modules/`uname -r`/kernel/drivers/net/wireless/wl.ko
oliver@sommernachtswind:~/Broadcom-STA64$ sudo depmod -a
oliver@sommernachtswind:~/Broadcom-STA64$ sudo modprobe wl
oliver@sommernachtswind:~/Broadcom-STA64$ iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

eth1      IEEE 802.11  Access Point: Not-Associated   
          Link Quality:5  Signal level:0  Noise level:245
          Rx invalid nwid:0  invalid crypt:0  invalid misc:0

Bis auf die Warnmeldung hat alles funktioniert. Hier ist noch diese module.h-Datei.

#ifndef _LINUX_MODULE_H
#define _LINUX_MODULE_H
/*
 * Dynamic loading of modules into the kernel.
 *
 * Rewritten by Richard Henderson <rth@tamu.edu> Dec 1996
 * Rewritten again by Rusty Russell, 2002
 */
#include <linux/list.h>
#include <linux/stat.h>
#include <linux/compiler.h>
#include <linux/cache.h>
#include <linux/kmod.h>
#include <linux/elf.h>
#include <linux/stringify.h>
#include <linux/kobject.h>
#include <linux/moduleparam.h>
#include <linux/tracepoint.h>

#include <linux/percpu.h>
#include <asm/module.h>

#include <trace/events/module.h>

/* Not Yet Implemented */
#define MODULE_SUPPORTED_DEVICE(name)

/* Some toolchains use a `_' prefix for all user symbols. */
#ifdef CONFIG_SYMBOL_PREFIX
#define MODULE_SYMBOL_PREFIX CONFIG_SYMBOL_PREFIX
#else
#define MODULE_SYMBOL_PREFIX ""
#endif

#define MODULE_NAME_LEN MAX_PARAM_PREFIX_LEN

struct kernel_symbol
{
	unsigned long value;
	const char *name;
};

struct modversion_info
{
	unsigned long crc;
	char name[MODULE_NAME_LEN];
};

struct module;

struct module_attribute {
        struct attribute attr;
        ssize_t (*show)(struct module_attribute *, struct module *, char *);
        ssize_t (*store)(struct module_attribute *, struct module *,
			 const char *, size_t count);
	void (*setup)(struct module *, const char *);
	int (*test)(struct module *);
	void (*free)(struct module *);
};

struct module_kobject
{
	struct kobject kobj;
	struct module *mod;
	struct kobject *drivers_dir;
	struct module_param_attrs *mp;
};

/* These are either module local, or the kernel's dummy ones. */
extern int init_module(void);
extern void cleanup_module(void);

/* Archs provide a method of finding the correct exception table. */
struct exception_table_entry;

const struct exception_table_entry *
search_extable(const struct exception_table_entry *first,
	       const struct exception_table_entry *last,
	       unsigned long value);
void sort_extable(struct exception_table_entry *start,
		  struct exception_table_entry *finish);
void sort_main_extable(void);
void trim_init_extable(struct module *m);

#ifdef MODULE
#define MODULE_GENERIC_TABLE(gtype,name)			\
extern const struct gtype##_id __mod_##gtype##_table		\
  __attribute__ ((unused, alias(__stringify(name))))

extern struct module __this_module;
#define THIS_MODULE (&__this_module)
#else  /* !MODULE */
#define MODULE_GENERIC_TABLE(gtype,name)
#define THIS_MODULE ((struct module *)0)
#endif

/* Generic info of form tag = "info" */
#define MODULE_INFO(tag, info) __MODULE_INFO(tag, tag, info)

/* For userspace: you can also call me... */
#define MODULE_ALIAS(_alias) MODULE_INFO(alias, _alias)

/*
 * The following license idents are currently accepted as indicating free
 * software modules
 *
 *	"GPL"				[GNU Public License v2 or later]
 *	"GPL v2"			[GNU Public License v2]
 *	"GPL and additional rights"	[GNU Public License v2 rights and more]
 *	"Dual BSD/GPL"			[GNU Public License v2
 *					 or BSD license choice]
 *	"Dual MIT/GPL"			[GNU Public License v2
 *					 or MIT license choice]
 *	"Dual MPL/GPL"			[GNU Public License v2
 *					 or Mozilla license choice]
 *
 * The following other idents are available
 *
 *	"Proprietary"			[Non free products]
 *
 * There are dual licensed components, but when running with Linux it is the
 * GPL that is relevant so this is a non issue. Similarly LGPL linked with GPL
 * is a GPL combined work.
 *
 * This exists for several reasons
 * 1.	So modinfo can show license info for users wanting to vet their setup 
 *	is free
 * 2.	So the community can ignore bug reports including proprietary modules
 * 3.	So vendors can do likewise based on their own policies
 */
#define MODULE_LICENSE(_license) MODULE_INFO(license, _license)

/*
 * Author(s), use "Name <email>" or just "Name", for multiple
 * authors use multiple MODULE_AUTHOR() statements/lines.
 */
#define MODULE_AUTHOR(_author) MODULE_INFO(author, _author)
  
/* What your module does. */
#define MODULE_DESCRIPTION(_description) MODULE_INFO(description, _description)

/* One for each parameter, describing how to use it.  Some files do
   multiple of these per line, so can't just use MODULE_INFO. */
#define MODULE_PARM_DESC(_parm, desc) \
	__MODULE_INFO(parm, _parm, #_parm ":" desc)

#define MODULE_DEVICE_TABLE(type,name)		\
  MODULE_GENERIC_TABLE(type##_device,name)

/* Version of form [<epoch>:]<version>[-<extra-version>].
   Or for CVS/RCS ID version, everything but the number is stripped.
  <epoch>: A (small) unsigned integer which allows you to start versions
           anew. If not mentioned, it's zero.  eg. "2:1.0" is after
	   "1:2.0".
  <version>: The <version> may contain only alphanumerics and the
           character `.'.  Ordered by numeric sort for numeric parts,
	   ascii sort for ascii parts (as per RPM or DEB algorithm).
  <extraversion>: Like <version>, but inserted for local
           customizations, eg "rh3" or "rusty1".

  Using this automatically adds a checksum of the .c files and the
  local headers in "srcversion".
*/
#define MODULE_VERSION(_version) MODULE_INFO(version, _version)

/* Optional firmware file (or files) needed by the module
 * format is simply firmware file name.  Multiple firmware
 * files require multiple MODULE_FIRMWARE() specifiers */
#define MODULE_FIRMWARE(_firmware) MODULE_INFO(firmware, _firmware)

/* Given an address, look for it in the exception tables */
const struct exception_table_entry *search_exception_tables(unsigned long add);

struct notifier_block;

#ifdef CONFIG_MODULES

extern int modules_disabled; /* for sysctl */
/* Get/put a kernel symbol (calls must be symmetric) */
void *__symbol_get(const char *symbol);
void *__symbol_get_gpl(const char *symbol);
#define symbol_get(x) ((typeof(&x))(__symbol_get(MODULE_SYMBOL_PREFIX #x)))

/* modules using other modules: kdb wants to see this. */
struct module_use {
	struct list_head source_list;
	struct list_head target_list;
	struct module *source, *target;
};

#ifndef __GENKSYMS__
#ifdef CONFIG_MODVERSIONS
/* Mark the CRC weak since genksyms apparently decides not to
 * generate a checksums for some symbols */
#define __CRC_SYMBOL(sym, sec)					\
	extern void *__crc_##sym __attribute__((weak));		\
	static const unsigned long __kcrctab_##sym		\
	__used							\
	__attribute__((section("__kcrctab" sec), unused))	\
	= (unsigned long) &__crc_##sym;
#else
#define __CRC_SYMBOL(sym, sec)
#endif

/* For every exported symbol, place a struct in the __ksymtab section */
#define __EXPORT_SYMBOL(sym, sec)				\
	extern typeof(sym) sym;					\
	__CRC_SYMBOL(sym, sec)					\
	static const char __kstrtab_##sym[]			\
	__attribute__((section("__ksymtab_strings"), aligned(1))) \
	= MODULE_SYMBOL_PREFIX #sym;                    	\
	static const struct kernel_symbol __ksymtab_##sym	\
	__used							\
	__attribute__((section("__ksymtab" sec), unused))	\
	= { (unsigned long)&sym, __kstrtab_##sym }

#define EXPORT_SYMBOL(sym)					\
	__EXPORT_SYMBOL(sym, "")

#define EXPORT_SYMBOL_GPL(sym)					\
	__EXPORT_SYMBOL(sym, "_gpl")

#define EXPORT_SYMBOL_GPL_FUTURE(sym)				\
	__EXPORT_SYMBOL(sym, "_gpl_future")


#ifdef CONFIG_UNUSED_SYMBOLS
#define EXPORT_UNUSED_SYMBOL(sym) __EXPORT_SYMBOL(sym, "_unused")
#define EXPORT_UNUSED_SYMBOL_GPL(sym) __EXPORT_SYMBOL(sym, "_unused_gpl")
#else
#define EXPORT_UNUSED_SYMBOL(sym)
#define EXPORT_UNUSED_SYMBOL_GPL(sym)
#endif

#endif

enum module_state
{
	MODULE_STATE_LIVE,
	MODULE_STATE_COMING,
	MODULE_STATE_GOING,
};

struct module
{
	enum module_state state;

	/* Member of list of modules */
	struct list_head list;

	/* Unique handle for this module */
	char name[MODULE_NAME_LEN];

	/* Sysfs stuff. */
	struct module_kobject mkobj;
	struct module_attribute *modinfo_attrs;
	const char *version;
	const char *srcversion;
	struct kobject *holders_dir;

	/* Exported symbols */
	const struct kernel_symbol *syms;
	const unsigned long *crcs;
	unsigned int num_syms;

	/* Kernel parameters. */
	struct kernel_param *kp;
	unsigned int num_kp;

	/* GPL-only exported symbols. */
	unsigned int num_gpl_syms;
	const struct kernel_symbol *gpl_syms;
	const unsigned long *gpl_crcs;

#ifdef CONFIG_UNUSED_SYMBOLS
	/* unused exported symbols. */
	const struct kernel_symbol *unused_syms;
	const unsigned long *unused_crcs;
	unsigned int num_unused_syms;

	/* GPL-only, unused exported symbols. */
	unsigned int num_unused_gpl_syms;
	const struct kernel_symbol *unused_gpl_syms;
	const unsigned long *unused_gpl_crcs;
#endif

	/* symbols that will be GPL-only in the near future. */
	const struct kernel_symbol *gpl_future_syms;
	const unsigned long *gpl_future_crcs;
	unsigned int num_gpl_future_syms;

	/* Exception table */
	unsigned int num_exentries;
	struct exception_table_entry *extable;

	/* Startup function. */
	int (*init)(void);

	/* If this is non-NULL, vfree after init() returns */
	void *module_init;

	/* Here is the actual code + data, vfree'd on unload. */
	void *module_core;

	/* Here are the sizes of the init and core sections */
	unsigned int init_size, core_size;

	/* The size of the executable code in each section.  */
	unsigned int init_text_size, core_text_size;

	/* Arch-specific module values */
	struct mod_arch_specific arch;

	unsigned int taints;	/* same bits as kernel:tainted */

#ifdef CONFIG_GENERIC_BUG
	/* Support for BUG */
	unsigned num_bugs;
	struct list_head bug_list;
	struct bug_entry *bug_table;
#endif

#ifdef CONFIG_KALLSYMS
	/*
	 * We keep the symbol and string tables for kallsyms.
	 * The core_* fields below are temporary, loader-only (they
	 * could really be discarded after module init).
	 */
	Elf_Sym *symtab, *core_symtab;
	unsigned int num_symtab, core_num_syms;
	char *strtab, *core_strtab;

	/* Section attributes */
	struct module_sect_attrs *sect_attrs;

	/* Notes attributes */
	struct module_notes_attrs *notes_attrs;
#endif

#ifdef CONFIG_SMP
	/* Per-cpu data. */
	void __percpu *percpu;
	unsigned int percpu_size;
#endif

	/* The command line arguments (may be mangled).  People like
	   keeping pointers to this stuff */
	char *args;
#ifdef CONFIG_TRACEPOINTS
	struct tracepoint *tracepoints;
	unsigned int num_tracepoints;
#endif

#ifdef CONFIG_TRACING
	const char **trace_bprintk_fmt_start;
	unsigned int num_trace_bprintk_fmt;
#endif
#ifdef CONFIG_EVENT_TRACING
	struct ftrace_event_call *trace_events;
	unsigned int num_trace_events;
#endif
#ifdef CONFIG_FTRACE_MCOUNT_RECORD
	unsigned long *ftrace_callsites;
	unsigned int num_ftrace_callsites;
#endif

#ifdef CONFIG_MODULE_UNLOAD
	/* What modules depend on me? */
	struct list_head source_list;
	/* What modules do I depend on? */
	struct list_head target_list;

	/* Who is waiting for us to be unloaded */
	struct task_struct *waiter;

	/* Destruction function. */
	void (*exit)(void);

	struct module_ref {
		unsigned int incs;
		unsigned int decs;
	} __percpu *refptr;
#endif

#ifdef CONFIG_CONSTRUCTORS
	/* Constructor functions. */
	ctor_fn_t *ctors;
	unsigned int num_ctors;
#endif
};
#ifndef MODULE_ARCH_INIT
#define MODULE_ARCH_INIT {}
#endif

extern struct mutex module_mutex;

/* FIXME: It'd be nice to isolate modules during init, too, so they
   aren't used before they (may) fail.  But presently too much code
   (IDE & SCSI) require entry into the module during init.*/
static inline int module_is_live(struct module *mod)
{
	return mod->state != MODULE_STATE_GOING;
}

struct module *__module_text_address(unsigned long addr);
struct module *__module_address(unsigned long addr);
bool is_module_address(unsigned long addr);
bool is_module_percpu_address(unsigned long addr);
bool is_module_text_address(unsigned long addr);

static inline int within_module_core(unsigned long addr, struct module *mod)
{
	return (unsigned long)mod->module_core <= addr &&
	       addr < (unsigned long)mod->module_core + mod->core_size;
}

static inline int within_module_init(unsigned long addr, struct module *mod)
{
	return (unsigned long)mod->module_init <= addr &&
	       addr < (unsigned long)mod->module_init + mod->init_size;
}

/* Search for module by name: must hold module_mutex. */
struct module *find_module(const char *name);

struct symsearch {
	const struct kernel_symbol *start, *stop;
	const unsigned long *crcs;
	enum {
		NOT_GPL_ONLY,
		GPL_ONLY,
		WILL_BE_GPL_ONLY,
	} licence;
	bool unused;
};

/* Search for an exported symbol by name. */
const struct kernel_symbol *find_symbol(const char *name,
					struct module **owner,
					const unsigned long **crc,
					bool gplok,
					bool warn);

/* Walk the exported symbol table */
bool each_symbol(bool (*fn)(const struct symsearch *arr, struct module *owner,
			    unsigned int symnum, void *data), void *data);

/* Returns 0 and fills in value, defined and namebuf, or -ERANGE if
   symnum out of range. */
int module_get_kallsym(unsigned int symnum, unsigned long *value, char *type,
			char *name, char *module_name, int *exported);

/* Look for this name: can be of form module:name. */
unsigned long module_kallsyms_lookup_name(const char *name);

int module_kallsyms_on_each_symbol(int (*fn)(void *, const char *,
					     struct module *, unsigned long),
				   void *data);

extern void __module_put_and_exit(struct module *mod, long code)
	__attribute__((noreturn));
#define module_put_and_exit(code) __module_put_and_exit(THIS_MODULE, code);

#ifdef CONFIG_MODULE_UNLOAD
unsigned int module_refcount(struct module *mod);
void __symbol_put(const char *symbol);
#define symbol_put(x) __symbol_put(MODULE_SYMBOL_PREFIX #x)
void symbol_put_addr(void *addr);

/* Sometimes we know we already have a refcount, and it's easier not
   to handle the error case (which only happens with rmmod --wait). */
static inline void __module_get(struct module *module)
{
	if (module) {
		preempt_disable();
		__this_cpu_inc(module->refptr->incs);
		trace_module_get(module, _THIS_IP_);
		preempt_enable();
	}
}

static inline int try_module_get(struct module *module)
{
	int ret = 1;

	if (module) {
		preempt_disable();

		if (likely(module_is_live(module))) {
			__this_cpu_inc(module->refptr->incs);
			trace_module_get(module, _THIS_IP_);
		} else
			ret = 0;

		preempt_enable();
	}
	return ret;
}

extern void module_put(struct module *module);

#else /*!CONFIG_MODULE_UNLOAD*/
static inline int try_module_get(struct module *module)
{
	return !module || module_is_live(module);
}
static inline void module_put(struct module *module)
{
}
static inline void __module_get(struct module *module)
{
}
#define symbol_put(x) do { } while(0)
#define symbol_put_addr(p) do { } while(0)

#endif /* CONFIG_MODULE_UNLOAD */
int use_module(struct module *a, struct module *b);

/* This is a #define so the string doesn't get put in every .o file */
#define module_name(mod)			\
({						\
	struct module *__mod = (mod);		\
	__mod ? __mod->name : "kernel";		\
})

/* For kallsyms to ask for address resolution.  namebuf should be at
 * least KSYM_NAME_LEN long: a pointer to namebuf is returned if
 * found, otherwise NULL. */
const char *module_address_lookup(unsigned long addr,
			    unsigned long *symbolsize,
			    unsigned long *offset,
			    char **modname,
			    char *namebuf);
int lookup_module_symbol_name(unsigned long addr, char *symname);
int lookup_module_symbol_attrs(unsigned long addr, unsigned long *size, unsigned long *offset, char *modname, char *name);

/* For extable.c to search modules' exception tables. */
const struct exception_table_entry *search_module_extables(unsigned long addr);

int register_module_notifier(struct notifier_block * nb);
int unregister_module_notifier(struct notifier_block * nb);

extern void print_modules(void);

extern void module_update_tracepoints(void);
extern int module_get_iter_tracepoints(struct tracepoint_iter *iter);

#else /* !CONFIG_MODULES... */
#define EXPORT_SYMBOL(sym)
#define EXPORT_SYMBOL_GPL(sym)
#define EXPORT_SYMBOL_GPL_FUTURE(sym)
#define EXPORT_UNUSED_SYMBOL(sym)
#define EXPORT_UNUSED_SYMBOL_GPL(sym)

/* Given an address, look for it in the exception tables. */
static inline const struct exception_table_entry *
search_module_extables(unsigned long addr)
{
	return NULL;
}

static inline struct module *__module_address(unsigned long addr)
{
	return NULL;
}

static inline struct module *__module_text_address(unsigned long addr)
{
	return NULL;
}

static inline bool is_module_address(unsigned long addr)
{
	return false;
}

static inline bool is_module_percpu_address(unsigned long addr)
{
	return false;
}

static inline bool is_module_text_address(unsigned long addr)
{
	return false;
}

/* Get/put a kernel symbol (calls should be symmetric) */
#define symbol_get(x) ({ extern typeof(x) x __attribute__((weak)); &(x); })
#define symbol_put(x) do { } while(0)
#define symbol_put_addr(x) do { } while(0)

static inline void __module_get(struct module *module)
{
}

static inline int try_module_get(struct module *module)
{
	return 1;
}

static inline void module_put(struct module *module)
{
}

#define module_name(mod) "kernel"

/* For kallsyms to ask for address resolution.  NULL means not found. */
static inline const char *module_address_lookup(unsigned long addr,
					  unsigned long *symbolsize,
					  unsigned long *offset,
					  char **modname,
					  char *namebuf)
{
	return NULL;
}

static inline int lookup_module_symbol_name(unsigned long addr, char *symname)
{
	return -ERANGE;
}

static inline int lookup_module_symbol_attrs(unsigned long addr, unsigned long *size, unsigned long *offset, char *modname, char *name)
{
	return -ERANGE;
}

static inline int module_get_kallsym(unsigned int symnum, unsigned long *value,
					char *type, char *name,
					char *module_name, int *exported)
{
	return -ERANGE;
}

static inline unsigned long module_kallsyms_lookup_name(const char *name)
{
	return 0;
}

static inline int module_kallsyms_on_each_symbol(int (*fn)(void *, const char *,
							   struct module *,
							   unsigned long),
						 void *data)
{
	return 0;
}

static inline int register_module_notifier(struct notifier_block * nb)
{
	/* no events will happen anyway, so this can always succeed */
	return 0;
}

static inline int unregister_module_notifier(struct notifier_block * nb)
{
	return 0;
}

#define module_put_and_exit(code) do_exit(code)

static inline void print_modules(void)
{
}

static inline void module_update_tracepoints(void)
{
}

static inline int module_get_iter_tracepoints(struct tracepoint_iter *iter)
{
	return 0;
}

#endif /* CONFIG_MODULES */

#ifdef CONFIG_SYSFS
extern struct kset *module_kset;
extern struct kobj_type module_ktype;
extern int module_sysfs_initialized;
#endif /* CONFIG_SYSFS */

#define symbol_request(x) try_then_request_module(symbol_get(x), "symbol:" #x)

/* BELOW HERE ALL THESE ARE OBSOLETE AND WILL VANISH */

#define __MODULE_STRING(x) __stringify(x)


#ifdef CONFIG_GENERIC_BUG
int  module_bug_finalize(const Elf_Ehdr *, const Elf_Shdr *,
			 struct module *);
void module_bug_cleanup(struct module *);

#else	/* !CONFIG_GENERIC_BUG */

static inline int  module_bug_finalize(const Elf_Ehdr *hdr,
					const Elf_Shdr *sechdrs,
					struct module *mod)
{
	return 0;
}
static inline void module_bug_cleanup(struct module *mod) {}
#endif	/* CONFIG_GENERIC_BUG */

#endif /* _LINUX_MODULE_H */

Unter System-Systemverwaltung-Zusätzliche Treiber findet sich jetzt der STA-Treiber. Er ist aber noch deaktiviert. Den muss ich jetzt wohl aktivieren, oder? (Ich frage lieber nach. Wahrscheinlich eine blöde Frage, aber ich weiß einfach nicht mehr weiter, daher bitte ich das zu entschuldigen.)

Ach, noch was: Ich habe beim Booten jetzt die Wahl zwischen 2.6.35-22 und 2.6.35-24. Ich muss letzeren wählen, oder?

elektronenblitz63

Avatar von elektronenblitz63

Anmeldungsdatum:
16. Januar 2007

Beiträge: 29307

Wohnort: NRW

Unter System-Systemverwaltung-Zusätzliche Treiber findet sich jetzt der STA-Treiber. Er ist aber noch deaktiviert. Den muss ich jetzt wohl aktivieren, oder?

Nein, momentan auf keinen Fall aktivieren. Der aktuelle Broadcom-Treiber wurde jetzt für eine Kernelversion (2.6.35-24) manuell installiert. Mal schauen. Funktioniert nun die Verbindung über WLAN?

Kuss_der_Diebe

(Themenstarter)

Anmeldungsdatum:
26. Juli 2008

Beiträge: 77

Wohnort: Köln

Ne, leider noch immer nicht. ☹

elektronenblitz63

Avatar von elektronenblitz63

Anmeldungsdatum:
16. Januar 2007

Beiträge: 29307

Wohnort: NRW

Es kann eigentlich nicht mehr am Treiber liegen. Bei den Acer-Modellen gibt es oft ein Problem mit der Sondertaste/Schalter für WLAN.

Was zeigt

rfkill list
rfkill unblock all
rfkill list

Dieses Modell ist recht neu, entsprechnde Module wie acer-wmi zur Steuerung der Sondertasten wurden nicht automtisch geladen. Teste bitte mal auf Verdacht hin

sudo modprobe acer-wmi wireless=1

Kuss_der_Diebe

(Themenstarter)

Anmeldungsdatum:
26. Juli 2008

Beiträge: 77

Wohnort: Köln

oliver@sommernachtswind:~$ rfkill list
0: brcmwl-0: Wireless LAN
	Soft blocked: no
	Hard blocked: no
oliver@sommernachtswind:~$ rfkill unblock all
oliver@sommernachtswind:~$ rfkill list
0: brcmwl-0: Wireless LAN
	Soft blocked: no
	Hard blocked: no
oliver@sommernachtswind:~$ sudo modprobe acer-wmi wireless=1
[sudo] password for oliver: 
FATAL: Error inserting acer_wmi (/lib/modules/2.6.35-24-generic/kernel/drivers/platform/x86/acer-wmi.ko): Unknown symbol in module, or unknown parameter (see dmesg)
oliver@sommernachtswind:~$ 

elektronenblitz63

Avatar von elektronenblitz63

Anmeldungsdatum:
16. Januar 2007

Beiträge: 29307

Wohnort: NRW

Ok, Karte ist definitiv auch nicht abgeschaltet.

Entferne den Treiber:

sudo rm /lib/modules/$(uname -r)/kernel/drivers/net/wireless/wl.ko
sudo depmod -a

Verbinde wieder beide Rechner über Kabel, starte die Aktualisierungsverwaltung und bringe das System auf einen aktuellen Stand. Installiere dann über den restricted-manager den Broadcom STA-Treiber der ja nun angeboten wird. Probiere es erneut über WLAN. Die Kabelverbindung dazu trennen!

Ich habe allerdings eher den Verdacht, dass es an den Einstellungen des Routers und nicht am Treiber liegt. Aber mal abwarten. Gibt es ansonsten die Möglichkeit mal bei einem der Nachbarn probeweise das WLAN verwenden zu dürfen um so die Hardware und den Treiber besser testen zu können?

Kuss_der_Diebe

(Themenstarter)

Anmeldungsdatum:
26. Juli 2008

Beiträge: 77

Wohnort: Köln

Guten Morgen elektronenblitz63,

ich bin gerade in der Uni und habe versucht, mich ins Uni-Netz einzuwählen.... Und siehe da.... Es funktioniert.... Ich bin völlig fassungslos... Habe es wochenlang versucht, 100erte Beiträge gelesen, Nächte durchgemacht und dann das.... Natürlich freue ich mich auch, dass es wohl doch nicht so kompliziert ist, wie es in vielen Foren den Anschein macht.

Dann wird´s wohl wirklich am Router liegen.

Da kann ich mich aber erst heute Nachmittag mit beschäftigen, da ich bis dahin in der Uni bin.

Hast du eine Idee, woran es eventuell liegen könnte?

Schon mal vielen, vielen Dank!

elektronenblitz63

Avatar von elektronenblitz63

Anmeldungsdatum:
16. Januar 2007

Beiträge: 29307

Wohnort: NRW

Hallo,
ein Treiberproblem wird immer unwahrscheinlicher.

Der Treiber aus den offiziellen Repost wird mittels DKMS installiert, hat also den Vorteil bei einem Kernelupdate nicht manuell nachinstalliert werden zu müssen, was momentan der Fall wäre. Der momentan installierte Treiber von Broadcom dürfte etwas aktueller sein, was aber nicht unbedingt erforderlich sein muss. Müsstest Du einfach ausprobieren.

Dann wird´s wohl wirklich am Router liegen. Hast du eine Idee, woran es eventuell liegen könnte?

Schwer zu sagen, kenne das Modell und die Einstellungen ja nicht.

MAC-Filter ist ja eigentlich auszuschließen. Frage doch mal den "Admin" ob der MAC-Filter aktiv ist, da Du ja deinen neuen Rechner anmelden möchtest und warum noch unsichere WEP-Verschlüsselung verwendet wird.

Entweder unterstützt der Router keine WPA oder auch WPA2-Verschlüsselung, was eher unwahrscheinlich ist, oder einer der angeschlossenen Rechner beherrscht das nicht, was zu überprüfen wäre 😉 . Eine unsichtbare SSID stellt auch absolut kein zusätzliches Sicherheitsmerkmal dar, erhöht nur den Traffic etwas.

Kuss_der_Diebe

(Themenstarter)

Anmeldungsdatum:
26. Juli 2008

Beiträge: 77

Wohnort: Köln

Lieber elektronenblitz63!

ES FUNKTIONIERT...! 😉 Vielen, vielen Dank!

Mir ist es eigentlich ganz schön peinlich... Der "Admin" musste das Netz kurz öffnen, damit ich "beitreten" konnte...

Mann oh Mann... Wenn ich geahnt hätte, dass es so einfach ist. Da wäre ich aber auch gar nicht drauf gekommen, weil so enorm viele Leute mit einem BCM43225-Chipset WLAN-Probleme haben. Daher dachte ich, dass es damit zusammenhängt.

Eine Frage habe ich aber noch: Du hast geschrieben, dass der Treiber bei einem Kernel-Update nachinstalliert werden müsste. Jetzt soll der Treiber für den BCM43225 aber im neuen Kernel integriert sein. D.h. doch, dass ich nach dem nächsten Ubuntu-Update (11.04) nichts nachinstallieren muss, oder?

Nochmals vielen, vielen Dank! 👍

Ganz liebe Grüße!

Kuss_der_Diebe

(Themenstarter)

Anmeldungsdatum:
26. Juli 2008

Beiträge: 77

Wohnort: Köln

Da habe ich mich wohl zu früh gefreut...

Ich habe gerade das System aktualisiert. Es war ja eine jungfräuliche Ubuntu-Installation.

Und nun kann ich mich wieder nicht verbinden bzw. werden mir keinerlei Netze angezeigt.

Nun werde ich den Treiber wohl manuell installieren müssen. Da ich das schon einige Male gemacht habe, sollte ich das schon hinbekommen. Die Frage ist nur, welchen ich nehmen soll. Kann mir da einer weiterhelfen?

praseodym Team-Icon

Supporter
Avatar von praseodym

Anmeldungsdatum:
9. Februar 2009

Beiträge: 22111

Wohnort: ~

Zeige die Ausgaben von:

uname -a
modinfo wl | egrep 'versi|filen'