katzki
Anmeldungsdatum: 21. November 2012
Beiträge: Zähle...
|
Hallo, ich habe gestern ein neues Notebook geliefert bekommen - ein HP 635 AMD E-450 auf dem SUSE Linux vorinstalliert war. Ich habe nun Ubuntu 12.04 drüber installiert und bekomme nun das WLAN nicht zum laufen. Über das Network sehe ich, daß bei jedem Neustart der Airplane Mode angestellt ist und das Wirless daher Unavailable ist. Wie kann ich also nun das Wirless "anstellen", damit ich nich mher über das Kabel surfen muß?
Über das Terminal bekomme ich folgende Meldung: PCI (sysfs)
description: Ethernet interface
product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:06:00.0
logical name: eth0
version: 05
serial: a0:b3:cc:cb:e8:d4
size: 100Mbit/s
capacity: 100Mbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.1.2 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s
resources: irq:43 ioport:2000(size=256) memory:f0104000-f0104fff memory:f0100000-f0103fff
description: Wireless interface
product: AR9285 Wireless Network Adapter (PCI-Express)
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:07:00.0
logical name: wlan0
version: 01
serial: 44:6d:57:35:bb:5c
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=ath9k driverversion=3.2.0-33-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn
resources: irq:23 memory:f0200000-f020ffff
jire@jireg:~$
jire@jireg:~$ sudo /var/log/
sudo: /var/log/: command not found
jire@jireg:~$ sudo /var/messages /grep switch
sudo: /var/messages: command not found
jire@jireg:~$ rfkill unblock 0
jire@jireg:~$ sudi iwlist scan
No command 'sudi' found, did you mean:
Command 'sudo' from package 'sudo' (main)
Command 'sudo' from package 'sudo-ldap' (universe)
sudi: command not found
jire@jireg:~$ sudo iwlist scan
lo Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Network is down eth0 Interface doesn't support scanning.
|
katzki
(Themenstarter)
Anmeldungsdatum: 21. November 2012
Beiträge: 6
|
Nachtrag: folgende Infos bekomme ich aus dem Terminal. Wie unblocke ich das WIFI? 1
2
3
4
5
6
7
8
9
10
11
12
13 | jire@jireg:~$ sudo rfkill list all
0: hp-wifi: Wireless LAN
Soft blocked: yes
Hard blocked: yes
1: hp-bluetooth: Bluetooth
Soft blocked: yes
Hard blocked: yes
2: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
3: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yes
|
|
katzki
(Themenstarter)
Anmeldungsdatum: 21. November 2012
Beiträge: 6
|
Sorry.
Also:
1
2
3
4
5
6
7
8
9
10
11
12
13
14 |
PCI (sysfs)
-network
description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 05 serial: a0:b3:cc:cb:e8:d4 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.1.2 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0104000-f0104fff memory:f0100000-f0103fff
-network DISABLED
description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 01 serial: 44:6d:57:35:bb:5c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-33-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:23 memory:f0200000-f020ffff jire@jireg:~$ jire@jireg:~$ sudo /var/log/ sudo: /var/log/: command not found jire@jireg:~$ sudo /var/messages /grep switch sudo: /var/messages: command not found jire@jireg:~$ rfkill unblock 0 jire@jireg:~$ sudi iwlist scan No command 'sudi' found, did you mean: Command 'sudo' from package 'sudo' (main) Command 'sudo' from package 'sudo-ldap' (universe) sudi: command not found jire@jireg:~$ sudo iwlist scan lo Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
eth0 Interface doesn't support scanning.
|
1
2
3
4
5
6
7
8
9
10
11
12
13 | 0: hp-wifi:
Wireless LAN
Soft blocked: yes
Hard blocked: yes
1: hp-bluetooth: Bluetooth
Soft blocked: yes
Hard blocked: yes
2: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
3: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yes
|
Befehle die ich bisher ausprobiert habe (ohne Erfolg):
| sudo rfkill unblock all
sudo rfkill list all
|
|
katzki
(Themenstarter)
Anmeldungsdatum: 21. November 2012
Beiträge: 6
|
Verwendetes Gerät: HP 635 AMD E-450, angeschlossen asn Strom und über Kabel an einen Router von Alice (ist auch der Internetanbieter). Über das Kabel funktioniert das Internet ohne Probleme. Kernelversion:
| Linux jireg 3.2.0-33-generic-pae #52-Ubuntu SMP Thu Oct 18 16:39:21 UTC 2012 i686 athlon i386 GNU/Linux
|
Systemversion: Ubuntu 12.04 Kartenabfrage:
| 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05)
Subsystem: Hewlett-Packard Company Device [103c:3577]
Kernel driver in use: r8169
--
07:00.0 Network controller [0280]: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:1461]
Kernel driver in use: ath9k
|
Wie ist das Netzwerk konfiguriert:
| egrep -v "^$|^#" /etc/network/interfaces
auto lo
iface lo inet loopback
|
| egrep -v "^$|^#" /etc/resolv.conf
nameserver 127.0.0.1
search localdomain
|
|
127.0.0.1 localhost
127.0.1.1 jireg
::1 ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
|
Zuordnung der Schnittstellen: | # This file was automatically generated by the /lib/udev/write_net_rules
# program, run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single
# line, and change only the value of the NAME= key.
# PCI device 0x10ec:/sys/devices/pci0000:00/0000:00:15.1/0000:06:00.0 (r8169)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="a0:b3:cc:cb:e8:d4", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
# PCI device 0x168c:/sys/devices/pci0000:00/0000:00:15.3/0000:07:00.0 (ath9k)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="44:6d:57:35:bb:5c", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19 | ifconfig
eth0 Link encap:Ethernet HWaddr a0:b3:cc:cb:e8:d4
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::a2b3:ccff:fecb:e8d4/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:16105 errors:0 dropped:0 overruns:0 frame:0
TX packets:12311 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:18978996 (18.9 MB) TX bytes:1460484 (1.4 MB)
Interrupt:43 Base address:0xe000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1163 errors:0 dropped:0 overruns:0 frame:0
TX packets:1163 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:102867 (102.8 KB) TX bytes:102867 (102.8 KB)
|
| route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0
192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0
|
|
iwconfig
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=off
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
eth0 no wireless extensions.
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19 | iwlist chan
lo no frequency information.
wlan0 14 channels in total; available frequencies :
Channel 01 : 2.412 GHz
Channel 02 : 2.417 GHz
Channel 03 : 2.422 GHz
Channel 04 : 2.427 GHz
Channel 05 : 2.432 GHz
Channel 06 : 2.437 GHz
Channel 07 : 2.442 GHz
Channel 08 : 2.447 GHz
Channel 09 : 2.452 GHz
Channel 10 : 2.457 GHz
Channel 11 : 2.462 GHz
Channel 12 : 2.467 GHz
Channel 13 : 2.472 GHz
Channel 14 : 2.484 GHz
eth0 no frequency information.
|
| lo Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
eth0 Interface doesn't support scanning.
|
1
2
3
4
5
6
7
8
9
10
11
12
13 | rfkill list
0: hp-wifi: Wireless LAN
Soft blocked: yes
Hard blocked: yes
1: hp-bluetooth: Bluetooth
Soft blocked: yes
Hard blocked: yes
2: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
3: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yes
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56 | lsmod
Module Size Used by
usbhid 41906 0
hid 77392 1 usbhid
nls_iso8859_1 12617 1
nls_cp437 12751 1
vfat 17308 1
fat 55605 1 vfat
rfcomm 38139 12
bnep 17830 2
vesafb 13516 1
parport_pc 32114 0
ppdev 12849 0
snd_hda_codec_realtek 174313 1
snd_hda_codec_hdmi 31775 1
arc4 12473 2
ath9k 117326 0
snd_hda_intel 32765 5
snd_hda_codec 109562 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel
snd_hwdep 13276 1 snd_hda_codec
mac80211 436455 1 ath9k
joydev 17393 0
snd_pcm 80845 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
fglrx 2909855 150
snd_seq_midi 13132 0
snd_rawmidi 25424 1 snd_seq_midi
ath9k_common 13781 1 ath9k
ath9k_hw 391554 2 ath9k,ath9k_common
btusb 17912 2
snd_seq_midi_event 14475 1 snd_seq_midi
uvcvideo 67203 0
videodev 86588 1 uvcvideo
hp_wmi 13652 0
snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event
bluetooth 158438 23 rfcomm,bnep,btusb
rts_pstor 353215 0
psmouse 86486 0
sp5100_tco 13495 0
sparse_keymap 13658 1 hp_wmi
snd_timer 28931 2 snd_pcm,snd_seq
ath 19387 3 ath9k,ath9k_common,ath9k_hw
snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq
snd 62064 20 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
serio_raw 13027 0
k10temp 12990 0
cfg80211 178679 3 ath9k,mac80211,ath
soundcore 14635 1 snd
snd_page_alloc 14108 2 snd_hda_intel,snd_pcm
i2c_piix4 13093 0
mac_hid 13077 0
video 19068 0
wmi 18744 1 hp_wmi
lp 17455 0
parport 40930 3 parport_pc,ppdev,lp
r8169 56321 0
usb_storage 39646 1
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78 | dmesg | egrep 'net|eth|sky|sis|via|3c3|3c5|e100|8139|8169|acx|air|ath|atl|ar9|carl|atme|at7|herm|iwl|ipw|rtl8|r81|rt2|rt3|rt6|rt7|tg3|ssb|wl|b43|b44|ori|pri|p5|zd|ndis|wmi|ns8|FW'
[ 0.000000] DMI: Hewlett-Packard HP 635 Notebook PC /3577, BIOS F.43 12/13/2011
[ 0.162104] print_constraints: dummy:
[ 0.326714] pci_root PNP0A08:00: ignoring host bridge window [mem 0x000cc000-0x000cffff] (conflicts with Video ROM [mem 0x000c0000-0x000ce5ff])
[ 0.378131] i2c-core: driver [aat2870] using legacy suspend method
[ 0.378135] i2c-core: driver [aat2870] using legacy resume method
[ 0.381692] reserve RAM buffer: 00000000dff00000 - 00000000dfffffff
[ 0.381696] reserve RAM buffer: 0000000107000000 - 0000000107ffffff
[ 0.528169] pci 0000:00:12.0: PCI INT A disabled
[ 0.705169] audit: initializing netlink socket (disabled)
[ 0.778720] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.778727] ACPI: Thermal Zone [TSZ0] (62 C)
[ 1.252651] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.047721] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.047780] r8169 0000:06:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 2.047828] r8169 0000:06:00.0: setting latency timer to 64
[ 2.047905] r8169 0000:06:00.0: irq 43 for MSI/MSI-X
[ 2.057578] r8169 0000:06:00.0: eth0: RTL8105e at 0xf843e000, a0:b3:cc:cb:e8:d4, XID 00a00000 IRQ 43
[ 6.946007] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.535185] Adding 3778556k swap on /dev/sda5. Priority:-1 extents:1 across:3778556k
[ 8.672146] wmi: Mapper loaded
[ 9.985496] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 9.985515] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 9.985963] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 9.985980] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 10.978548] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 11.685560] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 11.685583] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 11.692317] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 11.692339] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 11.897345] ath9k 0000:07:00.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 11.897365] ath9k 0000:07:00.0: setting latency timer to 64
[ 11.947131] ath: EEPROM regdomain: 0x60
[ 11.947136] ath: EEPROM indicates we should expect a direct regpair map
[ 11.947143] ath: Country alpha2 being used: 00
[ 11.947146] ath: Regpair used: 0x60
[ 11.949963] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 12.105045] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 12.326009] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 12.327149] Registered led device: ath9k-phy0
[ 15.969009] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 19.115172] r8169 0000:06:00.0: eth0: link down
[ 19.115188] r8169 0000:06:00.0: eth0: link down
[ 19.115514] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.116419] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.171180] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 19.594877] audit_printk_skb: 3 callbacks suppressed
[ 19.687737] type=1400 audit(1353495947.688:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=960 comm="apparmor_parser"
[ 19.688776] type=1400 audit(1353495947.692:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=960 comm="apparmor_parser"
[ 20.747495] r8169 0000:06:00.0: eth0: link up
[ 20.747822] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 31.328081] eth0: no IPv6 routers present
[ 157.452419] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 157.452442] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 185.303960] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 185.304072] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 187.857595] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 187.857633] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 189.289406] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 189.289445] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 189.940277] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 189.940316] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 253.062957] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 253.062995] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 253.063820] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 253.063853] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 387.952781] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 387.952802] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 387.955711] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 387.955732] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 415.573395] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 415.573433] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 415.577000] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 415.577043] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 572.122236] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 572.122257] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 572.123132] ACPI Error: Method parse/execution failed [\_SB_.WMID.HWCD] (Node f74321b0), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
[ 572.123150] ACPI Error: Method parse/execution failed [\_SB_.WMID.WMAD] (Node f74326a8), AE_AML_BUFFER_LIMIT (20110623/psparse-536)
|
| NetworkingEnabled=true
WirelessEnabled=true
WWANEnabled=true
WimaxEnabled=true
|
| cat /etc/NetworkManager/NetworkManager.conf
[main]
plugins=ifupdown,keyfile
dns=dnsmasq
[ifupdown]
managed=false
|
|
bsn
Anmeldungsdatum: 17. September 2006
Beiträge: 6386
Wohnort: Baden-Württemberg
|
Hallo, dein Wlan braucht einen Startimpuls:
echo "options hp_wmi wireless=1" | sudo tee -a /etc/modprobe.d/hp_wmi.conf
Neustart Wlan testen. Gruß bsn
|
katzki
(Themenstarter)
Anmeldungsdatum: 21. November 2012
Beiträge: 6
|
Vielen Dank! Ok, ich habe das jetzt eingegeben - Ergebnis: | options hp_wmi wireless=1
|
Ich mache gleich einen Neustart - Kabel drin lassen oder besser raus tun?
|
bsn
Anmeldungsdatum: 17. September 2006
Beiträge: 6386
Wohnort: Baden-Württemberg
|
Hallo, nein da Kabel vorrang hat! Gruß bsn
|
katzki
(Themenstarter)
Anmeldungsdatum: 21. November 2012
Beiträge: 6
|
Cooool, es hat geklappt! Hab' vielen, vielen Dank, Du bist der Held des Tages! Danke!
|