pccardctl info
lsusb

fehlt noch. Offenbar keine PCI-Karte?!

pccardctl info

PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255

lsusb

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth
Bus 002 Device 002: ID 03f0:171d Hewlett-Packard Bluetooth 2.0 Interface [Broadcom BCM2045]

Immer noch nix, mal ohne Filter

lspci -nnk

00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] nee ATI RS690 Host Bridge [1002:7910]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel modules: ati-agp
00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI RS690 PCI to PCI Bridge (Internal gfx) [1002:7912]
	Kernel modules: shpchp
00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI Device [1002:7914]
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00:05.0 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI RS690 PCI to PCI Bridge (PCI Express Port 1) [1002:7915]
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI RS690 PCI to PCI Bridge (PCI Express Port 2) [1002:7916]
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00:12.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA [1002:4380]
	Subsystem: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA [1002:4380]
	Kernel driver in use: ahci
00:13.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) [1002:4387]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ohci_hcd
00:13.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) [1002:4388]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ohci_hcd
00:13.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) [1002:4389]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ohci_hcd
00:13.3 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) [1002:438a]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ohci_hcd
00:13.4 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) [1002:438b]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ohci_hcd
00:13.5 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) [1002:4386]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller [1002:4385] (rev 14)
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: piix4_smbus
	Kernel modules: sp5100_tco, i2c-piix4
00:14.1 IDE interface [0101]: Advanced Micro Devices [AMD] nee ATI SB600 IDE [1002:438c]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: pata_atiixp
	Kernel modules: pata_atiixp
00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) [1002:4383]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd-hda-intel
00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge [1002:438d]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge [1002:4384]
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
	Kernel driver in use: k8temp
	Kernel modules: k8temp
01:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RS690M [Radeon X1200 Series] [1002:791f]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: radeon
	Kernel modules: radeon
02:04.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b6)
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: yenta_cardbus
	Kernel modules: yenta_socket
10:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express [14e4:1713] (rev 02)
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: tg3
	Kernel modules: tg3

Nix

Vielleicht ein Wackelkontakt oder kaputt?! Im BIOS nachgesehen, ob es dort aktiv(ierbar) ist?

Guten Morgen geomaster,

hast du eine Live CD von der 10.04

Dann teste mit der, ob dort der Penal- Eintrag kommt. Achtung nicht installieren.

guten morgen...

Ja habe ich... ich glaub ich habe das Problem gefunden. Das Bios habe ich jetzt im original zustand zurück gesezt, jetzt wird im Reiter oben Funknetzwerke angezeigt. Aber es wird angezeigt das das Gerät nicht betriebsbereit ist das die Firmware fehlt.

was nu?

geomaster, du schreibst:

Aber es wird angezeigt, das das Gerät nicht betriebsbereit ist, das die Firmware fehlt.

Wo genau wird das angezeigt. Im Panal oder im BIOS?

Wenn es im Panel ist, kannst du ein Bild posten und was sagt

iwconfig

Hallo,
das BIOS zeigt eine fehlende Firmware nicht an.

Es dürfte sich um eine Broadcom-Karte handeln. Ob die Firmware benötigt wird oder ein anderer Treiber erforderlich ist kann man so nicht sagen, da die Angaben zur WLAN-Hardware ja bislang nicht gezeigt wurden bzw. werden konnten.

lspci -nnk

moin moin

so hab jetzt Ubuntu 11.10 drauf...der hat auch direkt den Wlan Treiber install. jetzt geht wieder alles, obwohl ich ja lieber die 12.04 Version hätte...

ist das jetzt richtig so?

iwconfig

lo        no wireless extensions.

eth0      no wireless extensions.

eth1      IEEE 802.11  Access Point: Not-Associated   
          Link Quality:5  Signal level:219  Noise level:164
          Rx invalid nwid:0  invalid crypt:259  invalid misc:0

geomaster@geomaster-laptop:~$ lspci -nnk
00:00.0 Host bridge [0600]: ATI Technologies Inc RS690 Host Bridge [1002:7910]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel modules: ati-agp
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) [1002:7912]
	Kernel modules: shpchp
00:04.0 PCI bridge [0604]: ATI Technologies Inc Device [1002:7914]
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00:05.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 1) [1002:7915]
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00:06.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) [1002:7916]
	Kernel driver in use: pcieport
	Kernel modules: shpchp
00:12.0 SATA controller [0106]: ATI Technologies Inc SB600 Non-Raid-5 SATA [1002:4380]
	Subsystem: ATI Technologies Inc SB600 Non-Raid-5 SATA [1002:4380]
	Kernel driver in use: ahci
	Kernel modules: ahci
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI0) [1002:4387]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ohci_hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI1) [1002:4388]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ohci_hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI2) [1002:4389]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ohci_hcd
00:13.3 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI3) [1002:438a]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ohci_hcd
00:13.4 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI4) [1002:438b]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ohci_hcd
00:13.5 USB Controller [0c03]: ATI Technologies Inc SB600 USB Controller (EHCI) [1002:4386]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 14)
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: piix4_smbus
	Kernel modules: sp5100_tco, i2c-piix4
00:14.1 IDE interface [0101]: ATI Technologies Inc SB600 IDE [1002:438c]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: pata_atiixp
	Kernel modules: pata_atiixp
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: HDA Intel
	Kernel modules: snd-hda-intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB600 PCI to LPC Bridge [1002:438d]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384]
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
	Kernel driver in use: k8temp
	Kernel modules: k8temp
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS690M [Radeon X1200 Series] [1002:791f]
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: radeon
	Kernel modules: radeon
02:04.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b6)
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: yenta_cardbus
	Kernel modules: yenta_socket
10:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express [14e4:1713] (rev 02)
	Subsystem: Hewlett-Packard Company Device [103c:30c2]
	Kernel driver in use: tg3
	Kernel modules: tg3
30:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11a/b/g [14e4:4312] (rev 02)
	Subsystem: Hewlett-Packard Company Broadcom 802.11a/b/g WLAN [103c:1371]
	Kernel driver in use: wl
	Kernel modules: wl, ssb

Danke für die Hilfe

Hallo geomaster,

wenn du 12.04 haben willst, vllt. kann dir hier speziell elektronenblitz63 helfen. Er hat mir auch schon bei dem Exoten von Medion geholfen. [Ps.: immer mit Erfolg, Grüße Rainer)

Möglicherweise funktioniert der 12.04-Treiber nicht auf den Kanälen 12 und 13 (Bug). Teste mal ne 12.04 Live-CD