ubuntuusers.de

Moin zusammen,

habe diese Webcam: Microdia PC Camera with Mic (SN9C105) - installiert habe ich Natty Narwhal. Bei dem Versuch Easycam zu installien erhalte ich diese Fehlermeldung: Die folgenden Pakete haben nicht erfüllte Abhängigkeiten:

easycam2-gtk: Depends: python2.4-glade2 aber es soll nicht installiert werden
              Depends: python2.4-gtk2 aber es soll nicht installiert werden

Das sollte der Treiber für meine Webcam sein: sn9c1xx-1.48.tar.gz - Habe ich heruntergeladen und ausgepackt. Aber die Anleitung zur Installation kann ich leider nicht umsetzen, hier die Anweisungen

:5. Driver installation
======================
As noted above, kernel 2.6.19 is the minimum for this driver; for it to work
properly, the driver needs kernel support for Video4Linux and USB.

The following options of the kernel configuration file must be enabled and
corresponding modules must be compiled:

	# Multimedia devices
	#
	CONFIG_VIDEO_DEV=m

To enable advanced debugging functionality on the device through /sysfs:

	# Multimedia devices
	#
	CONFIG_VIDEO_ADV_DEBUG=y

On the contrary, to disable the debugging functionality, it's necessary to both
set CONFIG_VIDEO_ADV_DEBUG=n and remove its definition from the Kbuild file
provided with the SN9C1xx driver.

	# USB support
	#
	CONFIG_USB=m

In addition, depending on the hardware being used, the modules below are
necessary:

	# USB Host Controller Drivers
	#
	CONFIG_USB_EHCI_HCD=m
	CONFIG_USB_UHCI_HCD=m
	CONFIG_USB_OHCI_HCD=m

The SN9C103, SN9C105 and SN9C120 controllers also provide a built-in microphone
interface. It is supported by the USB Audio driver thanks to the ALSA API:

	# Sound
	#
	CONFIG_SOUND=y

	# Advanced Linux Sound Architecture
	#
	CONFIG_SND=m

	# USB devices
	#
	CONFIG_SND_USB_AUDIO=m

Moving along to the SN9C1xx driver: after having downloaded the package,
decompress and compile:

	[user@localhost home]$ tar xvzf sn9c1xx-v.vv.tar.gz
	[user@localhost home]$ cd sn9c1xx-v.vv

(where "v.vv" has to be substituted with the version of the package just
downloaded)

It is necessary to properly configure your particular kernel source tree before
compiling the driver. The modular building process is used; therefore you must
have read and write access to your kernel source tree. If not, log in as root
before running the following commands:

	[user@localhost sn9c1xx-v.vv]$ make clean
	[user@localhost sn9c1xx-v.vv]$ make modules

If the commands fail, control the Makefile and change the path to the kernel
source tree or to any other files, according to your system configuration;
then run the previous commands again.

If everything went well, the SN9C1xx driver can be used either immediatly
(skip to the next paragraph) or be installed.

The driver will not be installed in the default directory reserved for modules
being built outside the kernel. This means that the possible version of the
driver present in the official Linux kernel tree might be overwritten during
the installation process.

To install the driver, run as root:

[root@localhost sn9c1xx-v.vv]# make modules_install

Jemand eine Idee, ob die Webcam installiert werden kann. Alternativ kann ich mir auch gut vorstellen, eine bessere Webcam neu zu kaufen die automatisch erkannt wird. 😉

Vielen Dank im Voraus und einen schönen Abend...

Beste Grüße aus Duisburg - Thorsten