Hallo,
Ich versuche aktuell eine serielle Verbindung zwischen PC (USB Serial Adapter PL2303) und Beamer Sanyo PLV Z2 aufzubauen.
:~$ lsusb Bus 002 Device 007: ID 2548:1002 Bus 002 Device 006: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port Bus 002 Device 005: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 004: ID 051d:0003 American Power Conversion UPS Bus 002 Device 003: ID 1a40:0101 Terminus Technology Inc. Hub Bus 002 Device 002: ID 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 003: ID 258a:1006 Bus 003 Device 002: ID 09da:9090 A4Tech Co., Ltd. XL-730K / XL-750BK / XL-755BK Mice Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 005 Device 002: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub :~$ modprobe usbserial vendor=0x067b product=0x2303 :~$ dmesg | grep tty [ 0.000000] console [tty0] enabled [ 1.626925] 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 19.891001] cdc_acm 2-4.4:1.0: ttyACM0: USB ACM device [ 19.942981] usb 2-4.3: pl2303 converter now attached to ttyUSB0 :~$ sudo chmod 777 /dev/ttyUSB0 [sudo] Passwort für server: :~$ cu -l /dev/ttyUSB0 Connected.
Ist die Verbindung so wirklich richtig eingerichtet? Wenn ja, wie sende ich nun meine Befehle, welche aus je 3 Character bestehen?
C00 power-on C01 power-off (unconditional) C02 power-off (Power Off ?) C05 input = Input 2 C07 input = Input 1 C0D no-show C0E return from no-show C11 standard C13 cinema C14 image 1 C15 image 2 C16 image 3 C17 image 4 C18 game C22 input 1 = auto C23 input 1 = video C24 input 1 = s-video C25 input 1 = D4-video (component) C1C menu on C1D menu off
Das Kabel zum Beamer ist nach dieser Anleitung http://www.avsforum.com/forum/68-digital-projectors-under-3-000-usd-msrp/359567-controlling-z2-via-rs232-service-port.html gebaut. Ich habe auch zwischen Pin 5 (GND) und Pin 2 8,6V scheinen die 10V aus der Anleitung zu sein...
MfG Basti
Moderiert von sebix:
Thema in einen passenden Forenbereich verschoben. Bitte beachte die als wichtig markierten Themen („Welche Themen gehören hier her und welche nicht?“) in jedem Forenbereich. Danke.