Danke, anbei das Ergebnis
sudo smartctl -a /dev/sda
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-5.0.0-13-generic] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Fujitsu MHZ BH
Device Model: FUJITSU MHZ2250BH G2
Serial Number: K617T8426KRB
LU WWN Device Id: 5 00000e 041e11bbb
Firmware Version: 8909
User Capacity: 250,059,350,016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 3f
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Mon Sep 23 21:25:17 2019 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 73) The previous self-test completed having
a test element that failed and the test
element that failed is not known.
Total time to complete Offline
data collection: ( 1009) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 143) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 036 046 Pre-fail Always In_the_past 99445
2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 47841280
3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 1
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 4049
5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 5 (1996 4)
7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always - 3096
8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 4835
10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0032 253 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2400
182 Erase_Fail_Count_Total 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0033 253 253 097 Pre-fail Always - 0
185 Unknown_Attribute 0x0010 253 253 000 Old_age Offline - 0
186 Unknown_Attribute 0x0032 095 095 000 Old_age Always - 5
187 Reported_Uncorrect 0x0032 253 001 000 Old_age Always - 281470706203124
188 Command_Timeout 0x0032 253 099 000 Old_age Always - 8
189 High_Fly_Writes 0x003a 253 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 062 044 000 Old_age Always - 38 (Min/Max 26/39)
191 G-Sense_Error_Rate 0x0032 253 099 000 Old_age Always - 16580609
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 9830550
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 48400
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 64
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 5 (0 5857)
197 Current_Pending_Sector 0x0012 098 091 000 Old_age Always - 3
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 17410
203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 2628605050706
240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 14980 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 14980 occurred at disk power-on lifetime: 4831 hours (201 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 5b 04 38 1a 40 Error: WP at LBA = 0x001a3804 = 1718276
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 18 80 38 0c 04 40 08 00:01:31.220 WRITE FPDMA QUEUED
60 08 58 00 38 1a 40 08 00:01:31.220 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 08 00:01:31.220 FLUSH CACHE EXT
ef 10 02 00 00 00 a0 08 00:01:31.220 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:01:31.219 IDENTIFY DEVICE
Error 14979 occurred at disk power-on lifetime: 4831 hours (201 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 f3 3b 0c 04 40 Error: UNC at LBA = 0x00040c3b = 265275
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 00 38 1a 40 08 00:01:26.316 READ FPDMA QUEUED
61 08 f0 30 0c 04 40 08 00:01:26.316 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 08 00:01:26.291 FLUSH CACHE EXT
61 18 d0 18 0c 04 40 08 00:01:26.086 WRITE FPDMA QUEUED
60 08 c8 00 38 da 40 08 00:01:26.086 READ FPDMA QUEUED
Error 14978 occurred at disk power-on lifetime: 4831 hours (201 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 83 d9 45 1a 40 Error: UNC at LBA = 0x001a45d9 = 1721817
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 d8 00 38 1a 40 08 00:01:21.064 READ FPDMA QUEUED
60 08 48 00 38 da 40 08 00:01:21.059 READ FPDMA QUEUED
60 08 c0 00 38 9a 40 08 00:01:21.048 READ FPDMA QUEUED
60 08 e8 00 38 5a 40 08 00:01:21.042 READ FPDMA QUEUED
60 08 a0 00 38 1a 40 08 00:01:21.025 READ FPDMA QUEUED
Error 14977 occurred at disk power-on lifetime: 4831 hours (201 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 9b 04 38 1a 40 Error: WP at LBA = 0x001a3804 = 1718276
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 18 18 70 09 04 40 08 00:01:10.341 WRITE FPDMA QUEUED
60 08 98 00 38 1a 40 08 00:01:10.339 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 08 00:01:10.339 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:01:10.338 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 08 00:01:10.338 SET FEATURES [Set transfer mode]
Error 14976 occurred at disk power-on lifetime: 4831 hours (201 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 7b 04 38 1a 40 Error: UNC at LBA = 0x001a3804 = 1718276
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 78 00 38 1a 40 08 00:01:05.451 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 08 00:01:05.440 FLUSH CACHE EXT
61 08 68 68 09 04 40 08 00:01:05.439 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 08 00:01:05.423 FLUSH CACHE EXT
60 80 48 00 38 9a 40 08 00:01:05.217 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: unknown failure 90% 4833 0
# 2 Extended offline Completed: unknown failure 90% 3807 0
# 3 Short offline Completed: unknown failure 90% 3807 0
# 4 Short offline Completed: unknown failure 90% 3806 0
# 5 Short offline Completed without error 00% 10 -
# 6 Short offline Completed without error 00% 3 -
# 7 Short offline Completed without error 00% 2 -
# 8 Short offline Completed without error 00% 2 -
# 9 Short offline Completed without error 00% 1 -
#10 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.