So, mit Version 3.3.0 und Windows-10-1909-64-Bit-ISO unter Ubuntu MATE 18.04 erstellt:
Erstellung läuft komplett fehlerfrei durch, Stick ist bootbar.
Klappt natürlich nur, wenn man in der GUI auch NTFS als Dateisystem ausgewählt hat.
Supporter
Anmeldungsdatum: Beiträge: 53583 Wohnort: Berlin |
So, mit Version 3.3.0 und Windows-10-1909-64-Bit-ISO unter Ubuntu MATE 18.04 erstellt: Erstellung läuft komplett fehlerfrei durch, Stick ist bootbar. Klappt natürlich nur, wenn man in der GUI auch NTFS als Dateisystem ausgewählt hat. |
Supporter
Anmeldungsdatum: Beiträge: 53583 Wohnort: Berlin |
Da musst du wohl mal die Entwickler fragen, was Exit code 256 ist. 😉 Das Log an sich zeigt keinerlei Fehler. |
Supporter
Anmeldungsdatum: Beiträge: 53583 Wohnort: Berlin |
Dieses Internet sagt, das liegt daran, dass du das Programm als Nutzer gestartet hast. Prüfen, ob der Stick eingebunden ist, wenn ja: Hänge ihn aus. Anschließend startest du das Programm per sudo -H woeusbgui und erstellst damit den Stick. |
(Themenstarter)
Anmeldungsdatum: Beiträge: 292 |
tomtomtom Habe es so wie du es geschrieben hast gemacht, es bleibt bei Fehlermeldung Installation failed! Exit code: 256 Log: WoeUSB v@@WOEUSB_VERSION@@ ============================== Mounting source filesystem... Wiping all existing partition table and filesystem signatures in /dev/sde... wipefs: Fehler: /dev/sde: Initialisierung der Suche ist gescheitert: Kein Medium gefunden The command "wipefs --all "${target_device}"" failed with exit status "1", program is prematurely aborted Unmounting and removing "/media/woeusb_source_1573926005_23290"... You may now safely detach the target device |
Supporter
Anmeldungsdatum: Beiträge: 53583 Wohnort: Berlin |
wipefs: Fehler: /dev/sde: Initialisierung der Suche ist gescheitert: Kein Medium gefunden
Das ist kein Problem von WoeUSB, da meldet schon das util-linux-Programm Da es sich hier um ein Problem mit dem Stick handeln kann bitte die Ausgabe von dmesg |
(Themenstarter)
Anmeldungsdatum: Beiträge: 292 |
Es ist doch sdehr lang, tomtomtom EAD) flags 0x0 phys_seg 1 prio class 0 [ 7417.970986] Buffer I/O error on dev sde1, logical block 1876917, async page read [ 7417.971192] blk_update_request: I/O error, dev sde, sector 15023528 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7417.971198] Buffer I/O error on dev sde1, logical block 1876917, async page read [ 7417.971215] blk_update_request: I/O error, dev sde, sector 15023528 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7417.971217] Buffer I/O error on dev sde1, logical block 1876917, async page read [ 7417.971350] blk_update_request: I/O error, dev sde, sector 15023528 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7417.971354] Buffer I/O error on dev sde1, logical block 1876917, async page read [ 7417.971369] blk_update_request: I/O error, dev sde, sector 15023528 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7417.971371] Buffer I/O error on dev sde1, logical block 1876917, async page read [ 7417.971376] blk_update_request: I/O error, dev sde, sector 8208 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 7417.971378] Buffer I/O error on dev sde1, logical block 2, lost async page write [ 7417.971409] blk_update_request: I/O error, dev sde, sector 8224 op 0x1:(WRITE) flags 0x0 phys_seg 2 prio class 0 [ 7417.971415] Buffer I/O error on dev sde1, logical block 4, lost async page write [ 7417.971419] Buffer I/O error on dev sde1, logical block 5, lost async page write [ 7417.971479] Buffer I/O error on dev sde1, logical block 10, lost async page write [ 7418.303345] usb 2-4: new SuperSpeed Gen 1 USB device number 94 using xhci_hcd [ 7418.330674] usb 2-4: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00 [ 7418.330678] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7418.330681] usb 2-4: Product: Ultra Fit [ 7418.330683] usb 2-4: Manufacturer: SanDisk [ 7418.330684] usb 2-4: SerialNumber: 4C530001310613117214 [ 7418.339730] usb-storage 2-4:1.0: USB Mass Storage device detected [ 7418.339943] scsi host12: usb-storage 2-4:1.0 [ 7419.347989] scsi 12:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 [ 7419.348321] sd 12:0:0:0: Attached scsi generic sg4 type 0 [ 7419.348626] sd 12:0:0:0: [sdf] 120127488 512-byte logical blocks: (61.5 GB/57.3 GiB) [ 7419.349909] sd 12:0:0:0: [sdf] Write Protect is off [ 7419.349912] sd 12:0:0:0: [sdf] Mode Sense: 43 00 00 00 [ 7419.351036] sd 12:0:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 7419.359703] sdf: sdf1 sdf2 [ 7419.362653] sd 12:0:0:0: [sdf] Attached SCSI removable disk [ 7421.330530] usb 2-4: USB disconnect, device number 94 [ 7421.371368] FAT-fs (sdf2): Directory bread(block 3) failed [ 7421.371372] FAT-fs (sdf2): Directory bread(block 4) failed [ 7421.371374] FAT-fs (sdf2): Directory bread(block 5) failed [ 7421.371375] FAT-fs (sdf2): Directory bread(block 6) failed [ 7421.371377] FAT-fs (sdf2): Directory bread(block 7) failed [ 7421.371381] FAT-fs (sdf2): Directory bread(block 8) failed [ 7421.371382] FAT-fs (sdf2): Directory bread(block 9) failed [ 7421.371383] FAT-fs (sdf2): Directory bread(block 10) failed [ 7421.371384] FAT-fs (sdf2): Directory bread(block 11) failed [ 7421.371386] FAT-fs (sdf2): Directory bread(block 12) failed [ 7421.675877] usb 2-4: new SuperSpeed Gen 1 USB device number 95 using xhci_hcd [ 7421.703136] usb 2-4: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00 [ 7421.703140] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7421.703142] usb 2-4: Product: Ultra Fit [ 7421.703144] usb 2-4: Manufacturer: SanDisk [ 7421.703146] usb 2-4: SerialNumber: 4C530001310613117214 [ 7421.712236] usb-storage 2-4:1.0: USB Mass Storage device detected [ 7421.712534] scsi host13: usb-storage 2-4:1.0 [ 7421.721221] FAT-fs (sdf2): unable to read boot sector to mark fs as dirty [ 7422.740138] scsi 13:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 [ 7422.740513] sd 13:0:0:0: Attached scsi generic sg4 type 0 [ 7422.740812] sd 13:0:0:0: [sdf] 120127488 512-byte logical blocks: (61.5 GB/57.3 GiB) [ 7422.742080] sd 13:0:0:0: [sdf] Write Protect is off [ 7422.742082] sd 13:0:0:0: [sdf] Mode Sense: 43 00 00 00 [ 7422.743124] sd 13:0:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 7422.752599] sdf: sdf1 sdf2 [ 7422.755075] sd 13:0:0:0: [sdf] Attached SCSI removable disk [ 7425.250602] usb 2-4: USB disconnect, device number 95 [ 7425.563480] usb 2-4: new SuperSpeed Gen 1 USB device number 96 using xhci_hcd [ 7425.590856] usb 2-4: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00 [ 7425.590859] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7425.590862] usb 2-4: Product: Ultra Fit [ 7425.590864] usb 2-4: Manufacturer: SanDisk [ 7425.590866] usb 2-4: SerialNumber: 4C530001310613117214 [ 7425.599919] usb-storage 2-4:1.0: USB Mass Storage device detected [ 7425.600177] scsi host12: usb-storage 2-4:1.0 [ 7425.635109] FAT-fs (sdf2): unable to read boot sector to mark fs as dirty [ 7426.611929] scsi 12:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 [ 7426.612284] sd 12:0:0:0: Attached scsi generic sg4 type 0 [ 7426.612534] sd 12:0:0:0: [sdf] 120127488 512-byte logical blocks: (61.5 GB/57.3 GiB) [ 7426.613837] sd 12:0:0:0: [sdf] Write Protect is off [ 7426.613840] sd 12:0:0:0: [sdf] Mode Sense: 43 00 00 00 [ 7426.614826] sd 12:0:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 7426.622557] sdf: sdf1 sdf2 [ 7426.625306] sd 12:0:0:0: [sdf] Attached SCSI removable disk [ 7426.946989] FAT-fs (sdf2): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 7428.094561] usb 2-4: USB disconnect, device number 96 [ 7428.094821] sd 12:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK [ 7428.094826] sd 12:0:0:0: [sdf] tag#0 CDB: Read(10) 28 00 07 28 fc 2b 00 00 01 00 [ 7428.094828] print_req_error: 249 callbacks suppressed [ 7428.094831] blk_update_request: I/O error, dev sdf, sector 120126507 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 7428.094861] blk_update_request: I/O error, dev sdf, sector 120126508 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0 [ 7428.094867] blk_update_request: I/O error, dev sdf, sector 120126507 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7428.094882] FAT-fs (sdf2): Directory bread(block 43) failed [ 7428.094901] blk_update_request: I/O error, dev sdf, sector 120126508 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7428.094910] FAT-fs (sdf2): Directory bread(block 44) failed [ 7428.094918] blk_update_request: I/O error, dev sdf, sector 120126509 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7428.094923] FAT-fs (sdf2): Directory bread(block 45) failed [ 7428.094930] blk_update_request: I/O error, dev sdf, sector 120126510 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7428.094934] FAT-fs (sdf2): Directory bread(block 46) failed [ 7428.094937] FAT-fs (sdf2): error, corrupted directory (invalid entries) [ 7428.094939] FAT-fs (sdf2): Filesystem has been set read-only [ 7428.094969] blk_update_request: I/O error, dev sdf, sector 120126465 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 7428.094972] buffer_io_error: 4827 callbacks suppressed [ 7428.094973] Buffer I/O error on dev sdf2, logical block 1, lost async page write [ 7428.094994] blk_update_request: I/O error, dev sdf, sector 120126466 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 7428.094997] Buffer I/O error on dev sdf2, logical block 2, lost async page write [ 7428.110501] FAT-fs (sdf2): Directory bread(block 3) failed [ 7428.110508] FAT-fs (sdf2): Directory bread(block 4) failed [ 7428.110510] FAT-fs (sdf2): Directory bread(block 5) failed [ 7428.110512] FAT-fs (sdf2): Directory bread(block 6) failed [ 7428.110514] FAT-fs (sdf2): Directory bread(block 7) failed [ 7428.110522] FAT-fs (sdf2): Directory bread(block 8) failed [ 7428.395433] usb 2-4: new SuperSpeed Gen 1 USB device number 97 using xhci_hcd [ 7428.422695] usb 2-4: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00 [ 7428.422699] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7428.422701] usb 2-4: Product: Ultra Fit [ 7428.422703] usb 2-4: Manufacturer: SanDisk [ 7428.422704] usb 2-4: SerialNumber: 4C530001310613117214 [ 7428.431832] usb-storage 2-4:1.0: USB Mass Storage device detected [ 7428.432102] scsi host12: usb-storage 2-4:1.0 [ 7429.459937] scsi 12:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 [ 7429.460250] scsi 12:0:0:0: Attached scsi generic sg4 type 0 [ 7429.460634] sd 12:0:0:0: [sdf] 120127488 512-byte logical blocks: (61.5 GB/57.3 GiB) [ 7429.461904] sd 12:0:0:0: [sdf] Write Protect is off [ 7429.461906] sd 12:0:0:0: [sdf] Mode Sense: 43 00 00 00 [ 7429.462927] sd 12:0:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 7429.470922] sdf: sdf1 sdf2 [ 7429.473654] sd 12:0:0:0: [sdf] Attached SCSI removable disk [ 7429.782064] FAT-fs (sdf2): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 7431.370614] usb 2-4: USB disconnect, device number 97 [ 7431.667370] usb 2-4: new SuperSpeed Gen 1 USB device number 98 using xhci_hcd [ 7431.694832] usb 2-4: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00 [ 7431.694837] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7431.694840] usb 2-4: Product: Ultra Fit [ 7431.694842] usb 2-4: Manufacturer: SanDisk [ 7431.694844] usb 2-4: SerialNumber: 4C530001310613117214 [ 7431.703671] usb-storage 2-4:1.0: USB Mass Storage device detected [ 7431.703951] scsi host12: usb-storage 2-4:1.0 [ 7432.723879] scsi 12:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 [ 7432.724268] sd 12:0:0:0: Attached scsi generic sg4 type 0 [ 7432.724593] sd 12:0:0:0: [sdf] 120127488 512-byte logical blocks: (61.5 GB/57.3 GiB) [ 7432.726095] sd 12:0:0:0: [sdf] Write Protect is off [ 7432.726098] sd 12:0:0:0: [sdf] Mode Sense: 43 00 00 00 [ 7432.727104] sd 12:0:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 7432.735421] sdf: sdf1 sdf2 [ 7432.738844] sd 12:0:0:0: [sdf] Attached SCSI removable disk [ 7433.067864] FAT-fs (sdf2): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 7434.446584] usb 2-4: USB disconnect, device number 98 [ 7434.446912] sd 12:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK [ 7434.446917] sd 12:0:0:0: [sdf] tag#0 CDB: Read(10) 28 00 07 28 fc 2b 00 00 01 00 [ 7434.446921] blk_update_request: I/O error, dev sdf, sector 120126507 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 7434.446959] blk_update_request: I/O error, dev sdf, sector 120126508 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0 [ 7434.446968] blk_update_request: I/O error, dev sdf, sector 120126507 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7434.446980] FAT-fs (sdf2): Directory bread(block 43) failed [ 7434.447004] blk_update_request: I/O error, dev sdf, sector 120126508 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7434.447014] FAT-fs (sdf2): Directory bread(block 44) failed [ 7434.447024] blk_update_request: I/O error, dev sdf, sector 120126509 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7434.447030] FAT-fs (sdf2): Directory bread(block 45) failed [ 7434.447039] blk_update_request: I/O error, dev sdf, sector 120126510 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7434.447044] FAT-fs (sdf2): Directory bread(block 46) failed [ 7434.447047] FAT-fs (sdf2): error, corrupted directory (invalid entries) [ 7434.447049] FAT-fs (sdf2): Filesystem has been set read-only [ 7434.447083] blk_update_request: I/O error, dev sdf, sector 120126465 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 7434.447086] Buffer I/O error on dev sdf2, logical block 1, lost async page write [ 7434.447123] blk_update_request: I/O error, dev sdf, sector 120126466 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 7434.447129] Buffer I/O error on dev sdf2, logical block 2, lost async page write [ 7434.461854] FAT-fs (sdf2): Directory bread(block 3) failed [ 7434.461861] FAT-fs (sdf2): Directory bread(block 4) failed [ 7434.461863] FAT-fs (sdf2): Directory bread(block 5) failed [ 7434.461865] FAT-fs (sdf2): Directory bread(block 6) failed [ 7434.461867] FAT-fs (sdf2): Directory bread(block 7) failed [ 7434.461874] FAT-fs (sdf2): Directory bread(block 8) failed [ 7434.751383] usb 2-4: new SuperSpeed Gen 1 USB device number 99 using xhci_hcd [ 7434.782722] usb 2-4: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00 [ 7434.782726] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7434.782728] usb 2-4: Product: Ultra Fit [ 7434.782730] usb 2-4: Manufacturer: SanDisk [ 7434.782732] usb 2-4: SerialNumber: 4C530001310613117214 [ 7434.791545] usb-storage 2-4:1.0: USB Mass Storage device detected [ 7434.791767] scsi host12: usb-storage 2-4:1.0 [ 7435.796070] scsi 12:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 [ 7435.796403] sd 12:0:0:0: Attached scsi generic sg4 type 0 [ 7435.796592] sd 12:0:0:0: [sdf] 120127488 512-byte logical blocks: (61.5 GB/57.3 GiB) [ 7435.797935] sd 12:0:0:0: [sdf] Write Protect is off [ 7435.797938] sd 12:0:0:0: [sdf] Mode Sense: 43 00 00 00 [ 7435.798952] sd 12:0:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 7435.807560] sdf: sdf1 sdf2 [ 7435.810949] sd 12:0:0:0: [sdf] Attached SCSI removable disk [ 7436.197623] FAT-fs (sdf2): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 7437.258613] usb 2-4: USB disconnect, device number 99 [ 7437.258647] sd 12:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK [ 7437.258653] sd 12:0:0:0: [sdf] tag#0 CDB: Read(10) 28 00 07 28 fc 2b 00 00 01 00 [ 7437.258657] blk_update_request: I/O error, dev sdf, sector 120126507 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 7437.258704] blk_update_request: I/O error, dev sdf, sector 120126508 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0 [ 7437.258715] FAT-fs (sdf2): Directory bread(block 43) failed [ 7437.258731] FAT-fs (sdf2): Directory bread(block 44) failed [ 7437.258743] FAT-fs (sdf2): Directory bread(block 45) failed [ 7437.258755] FAT-fs (sdf2): Directory bread(block 46) failed [ 7437.258758] FAT-fs (sdf2): error, corrupted directory (invalid entries) [ 7437.258760] FAT-fs (sdf2): Filesystem has been set read-only [ 7437.258799] Buffer I/O error on dev sdf2, logical block 1, lost async page write [ 7437.258857] Buffer I/O error on dev sdf2, logical block 2, lost async page write [ 7437.276697] FAT-fs (sdf2): Directory bread(block 3) failed [ 7437.276704] FAT-fs (sdf2): Directory bread(block 4) failed [ 7437.276706] FAT-fs (sdf2): Directory bread(block 5) failed [ 7437.276708] FAT-fs (sdf2): Directory bread(block 6) failed [ 7437.276710] FAT-fs (sdf2): Directory bread(block 7) failed [ 7437.276721] FAT-fs (sdf2): Directory bread(block 8) failed [ 7437.567416] usb 2-4: new SuperSpeed Gen 1 USB device number 100 using xhci_hcd [ 7437.594825] usb 2-4: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00 [ 7437.594831] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7437.594834] usb 2-4: Product: Ultra Fit [ 7437.594836] usb 2-4: Manufacturer: SanDisk [ 7437.594838] usb 2-4: SerialNumber: 4C530001310613117214 [ 7437.603642] usb-storage 2-4:1.0: USB Mass Storage device detected [ 7437.603905] scsi host12: usb-storage 2-4:1.0 [ 7438.612196] scsi 12:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 [ 7438.612611] sd 12:0:0:0: Attached scsi generic sg4 type 0 [ 7438.612868] sd 12:0:0:0: [sdf] 120127488 512-byte logical blocks: (61.5 GB/57.3 GiB) [ 7438.614316] sd 12:0:0:0: [sdf] Write Protect is off [ 7438.614318] sd 12:0:0:0: [sdf] Mode Sense: 43 00 00 00 [ 7438.615298] sd 12:0:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 7438.622982] sdf: sdf1 sdf2 [ 7438.625530] sd 12:0:0:0: [sdf] Attached SCSI removable disk [ 7438.965355] FAT-fs (sdf2): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 7440.226641] usb 2-4: USB disconnect, device number 100 [ 7440.226691] sd 12:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK [ 7440.226695] sd 12:0:0:0: [sdf] tag#0 CDB: Read(10) 28 00 07 28 fc 2b 00 00 01 00 [ 7440.226697] print_req_error: 6 callbacks suppressed [ 7440.226700] blk_update_request: I/O error, dev sdf, sector 120126507 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 7440.226744] sd 12:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK [ 7440.226747] sd 12:0:0:0: [sdf] tag#0 CDB: Read(10) 28 00 07 28 fc 2c 00 00 03 00 [ 7440.226748] blk_update_request: I/O error, dev sdf, sector 120126508 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0 [ 7440.226757] blk_update_request: I/O error, dev sdf, sector 120126509 op 0x0:(READ) flags 0x80000 phys_seg 2 prio class 0 [ 7440.226762] blk_update_request: I/O error, dev sdf, sector 120126507 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7440.226781] FAT-fs (sdf2): Directory bread(block 43) failed [ 7440.226801] blk_update_request: I/O error, dev sdf, sector 120126508 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7440.226808] FAT-fs (sdf2): Directory bread(block 44) failed [ 7440.226816] blk_update_request: I/O error, dev sdf, sector 120126509 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7440.226820] FAT-fs (sdf2): Directory bread(block 45) failed [ 7440.226828] blk_update_request: I/O error, dev sdf, sector 120126510 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7440.226837] FAT-fs (sdf2): Directory bread(block 46) failed [ 7440.226840] FAT-fs (sdf2): error, corrupted directory (invalid entries) [ 7440.226842] FAT-fs (sdf2): Filesystem has been set read-only [ 7440.226881] blk_update_request: I/O error, dev sdf, sector 120126465 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 7440.226886] Buffer I/O error on dev sdf2, logical block 1, lost async page write [ 7440.226913] blk_update_request: I/O error, dev sdf, sector 120126466 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 7440.226919] Buffer I/O error on dev sdf2, logical block 2, lost async page write [ 7440.240652] FAT-fs (sdf2): Directory bread(block 3) failed [ 7440.240658] FAT-fs (sdf2): Directory bread(block 4) failed [ 7440.240660] FAT-fs (sdf2): Directory bread(block 5) failed [ 7440.240663] FAT-fs (sdf2): Directory bread(block 6) failed [ 7440.240665] FAT-fs (sdf2): Directory bread(block 7) failed [ 7440.240673] FAT-fs (sdf2): Directory bread(block 8) failed [ 7440.571521] usb 2-4: new SuperSpeed Gen 1 USB device number 101 using xhci_hcd [ 7440.598962] usb 2-4: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00 [ 7440.598967] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7440.598969] usb 2-4: Product: Ultra Fit [ 7440.598971] usb 2-4: Manufacturer: SanDisk [ 7440.598972] usb 2-4: SerialNumber: 4C530001310613117214 [ 7440.608110] usb-storage 2-4:1.0: USB Mass Storage device detected [ 7440.608394] scsi host12: usb-storage 2-4:1.0 [ 7441.620152] scsi 12:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 [ 7441.620510] sd 12:0:0:0: Attached scsi generic sg4 type 0 [ 7441.620625] sd 12:0:0:0: [sdf] 120127488 512-byte logical blocks: (61.5 GB/57.3 GiB) [ 7441.621954] sd 12:0:0:0: [sdf] Write Protect is off [ 7441.621955] sd 12:0:0:0: [sdf] Mode Sense: 43 00 00 00 [ 7441.622913] sd 12:0:0:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 7441.630573] sdf: sdf1 sdf2 [ 7441.633149] sd 12:0:0:0: [sdf] Attached SCSI removable disk [ 7441.908125] FAT-fs (sdf2): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 7470.228976] Buffer I/O error on dev sdd1, logical block 1876853, async page read [ 7470.229067] Buffer I/O error on dev sdd1, logical block 1876853, async page read [ 7470.229124] Buffer I/O error on dev sdd1, logical block 1876853, async page read [ 7470.229158] Buffer I/O error on dev sdd1, logical block 1876853, async page read [ 7491.774963] Buffer I/O error on dev sdc1, logical block 1876853, async page read [ 7491.775057] Buffer I/O error on dev sdc1, logical block 1876853, async page read [ 7491.775093] Buffer I/O error on dev sdc1, logical block 1876853, async page read [ 7491.775132] Buffer I/O error on dev sdc1, logical block 1876853, async page read [ 7862.921285] Buffer I/O error on dev sde1, logical block 2, lost async page write [ 7862.921295] Buffer I/O error on dev sde1, logical block 4, lost async page write [ 7862.921299] Buffer I/O error on dev sde1, logical block 5, lost async page write [ 7862.921303] Buffer I/O error on dev sde1, logical block 28, lost async page write [ 7862.921307] Buffer I/O error on dev sde1, logical block 1876853, lost async page write [ 7862.921310] Buffer I/O error on dev sde1, logical block 7507391, lost async page write [ 7862.922129] PM: suspend entry (deep) [ 7862.922702] Filesystems sync: 0.000 seconds [ 7862.922852] Freezing user space processes ... (elapsed 0.003 seconds) done. [ 7862.926060] OOM killer disabled. [ 7862.926061] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 7862.927612] printk: Suspending console(s) (use no_console_suspend to debug) [ 7862.963561] serial 00:04: disabled [ 7862.963676] r8169 0000:1f:00.0 enp31s0: Link is Down [ 7862.964307] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 7862.964359] sd 0:0:0:0: [sda] Stopping disk [ 7862.976324] sd 5:0:0:0: [sdb] Synchronizing SCSI cache [ 7862.976396] sd 5:0:0:0: [sdb] Stopping disk [ 7865.532636] ACPI: Preparing to enter system sleep state S3 [ 7866.053055] PM: Saving platform NVS memory [ 7866.053101] Disabling non-boot CPUs ... [ 7866.053790] irq_migrate_all_off_this_cpu: 8 callbacks suppressed [ 7866.053792] IRQ 55: no longer affine to CPU1 [ 7866.054865] smpboot: CPU 1 is now offline [ 7866.057078] smpboot: CPU 2 is now offline [ 7866.058167] IRQ 38: no longer affine to CPU3 [ 7866.058186] IRQ 39: no longer affine to CPU3 [ 7866.058206] IRQ 50: no longer affine to CPU3 [ 7866.058224] IRQ 51: no longer affine to CPU3 [ 7866.058244] IRQ 58: no longer affine to CPU3 [ 7866.059263] smpboot: CPU 3 is now offline [ 7866.061464] smpboot: CPU 4 is now offline [ 7866.062472] IRQ 27: no longer affine to CPU5 [ 7866.062491] IRQ 28: no longer affine to CPU5 [ 7866.062511] IRQ 36: no longer affine to CPU5 [ 7866.062531] IRQ 44: no longer affine to CPU5 [ 7866.063618] smpboot: CPU 5 is now offline [ 7866.065857] smpboot: CPU 6 is now offline [ 7866.067955] smpboot: CPU 7 is now offline [ 7866.069339] ACPI: Low-level resume complete [ 7866.069389] PM: Restoring platform NVS memory [ 7866.211578] Enabling non-boot CPUs ... [ 7866.211624] x86: Booting SMP configuration: [ 7866.211625] smpboot: Booting Node 0 Processor 1 APIC 0x1 [ 7866.211840] microcode: CPU1: patch_level=0x0810100b [ 7866.214227] CPU1 is up [ 7866.214266] smpboot: Booting Node 0 Processor 2 APIC 0x2 [ 7866.214498] microcode: CPU2: patch_level=0x0810100b [ 7866.216904] CPU2 is up [ 7866.216918] smpboot: Booting Node 0 Processor 3 APIC 0x3 [ 7866.217121] microcode: CPU3: patch_level=0x0810100b [ 7866.219550] CPU3 is up [ 7866.219563] smpboot: Booting Node 0 Processor 4 APIC 0x4 [ 7866.219819] microcode: CPU4: patch_level=0x0810100b [ 7866.222271] CPU4 is up [ 7866.222284] smpboot: Booting Node 0 Processor 5 APIC 0x5 [ 7866.222493] microcode: CPU5: patch_level=0x0810100b [ 7866.225151] CPU5 is up [ 7866.225167] smpboot: Booting Node 0 Processor 6 APIC 0x6 [ 7866.225421] microcode: CPU6: patch_level=0x0810100b [ 7866.227902] CPU6 is up [ 7866.227914] smpboot: Booting Node 0 Processor 7 APIC 0x7 [ 7866.228123] microcode: CPU7: patch_level=0x0810100b [ 7866.230628] CPU7 is up [ 7866.231349] ACPI: Waking up from system sleep state S3 [ 7866.311915] usb usb1: root hub lost power or was reset [ 7866.311917] usb usb2: root hub lost power or was reset [ 7866.313495] serial 00:04: activated [ 7866.314574] sd 0:0:0:0: [sda] Starting disk [ 7866.315079] sd 5:0:0:0: [sdb] Starting disk [ 7866.423191] r8169 0000:1f:00.0 enp31s0: Link is Down [ 7866.638721] ata9: SATA link down (SStatus 0 SControl 300) [ 7866.712177] usb 2-4: reset SuperSpeed Gen 1 USB device number 101 using xhci_hcd [ 7866.787465] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 7866.787496] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7866.788699] ata1.00: supports DRM functions and may not be fully accessible [ 7866.789444] ata1.00: supports DRM functions and may not be fully accessible [ 7866.789964] ata1.00: configured for UDMA/133 [ 7866.791091] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 7866.800080] ahci 0000:15:00.1: port does not support device sleep [ 7866.807594] ata5.00: configured for UDMA/100 [ 7866.829567] ata2.00: configured for UDMA/100 [ 7866.863298] usb 1-7: reset full-speed USB device number 2 using xhci_hcd [ 7867.213987] OOM killer enabled. [ 7867.213988] Restarting tasks ... done. [ 7867.221027] PM: suspend exit [ 7869.507093] r8169 0000:1f:00.0 enp31s0: Link is Up - 1Gbps/Full - flow control rx/tx [ 7874.139157] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 7874.150971] ata6.00: configured for UDMA/133 [ 8188.637377] audit: type=1400 audit(1573961674.655:50): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/internet2/Schreibtisch/firefox" pid=6264 comm="pool" requested_mask="r" denied_mask="r" fsuid=1002 ouid=1002 [ 8188.637451] audit: type=1400 audit(1573961674.655:51): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/internet2/Schreibtisch/firefox" pid=6264 comm="pool" requested_mask="r" denied_mask="r" fsuid=1002 ouid=1002 [ 8188.637907] audit: type=1400 audit(1573961674.655:52): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/internet2/Schreibtisch/Sound.TC" pid=6264 comm="pool" requested_mask="r" denied_mask="r" fsuid=1002 ouid=1002 [ 8188.637910] audit: type=1400 audit(1573961674.655:53): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/internet2/Schreibtisch/.goutputstream-GQCDA0" pid=6264 comm="pool" requested_mask="r" denied_mask="r" fsuid=1002 ouid=1002 [ 8188.637912] audit: type=1400 audit(1573961674.655:54): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/internet2/Schreibtisch/Unterlagen.tc" pid=6264 comm="pool" requested_mask="r" denied_mask="r" fsuid=1002 ouid=1002 [ 8188.638377] audit: type=1400 audit(1573961674.655:55): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/internet2/Schreibtisch/Sound.TC" pid=6264 comm="pool" requested_mask="r" denied_mask="r" fsuid=1002 ouid=1002 [ 8188.638596] audit: type=1400 audit(1573961674.655:56): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/internet2/Schreibtisch/.goutputstream-GQCDA0" pid=6264 comm="pool" requested_mask="r" denied_mask="r" fsuid=1002 ouid=1002 [ 8188.638846] audit: type=1400 audit(1573961674.655:57): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/internet2/Schreibtisch/Unterlagen.tc" pid=6264 comm="pool" requested_mask="r" denied_mask="r" fsuid=1002 ouid=1002 |
Supporter
Anmeldungsdatum: Beiträge: 53583 Wohnort: Berlin |
Jede Menge Eingabe-/Ausgabefehler des Sticks, der dürfte schlichtweg defekt sein. |
(Themenstarter)
Anmeldungsdatum: Beiträge: 292 |
Ok dann gelöst |