Hallo, ich komme gerade vom Artikel Festplattenstatus
Meine Ausgabe von dem smartctl - Ausführlicher Test ergibt folgende Ausgabe:
=== START OF INFORMATION SECTION === Device Model: C300-MTFDBAK128MAG Serial Number: 00000000111403057C08 LU WWN Device Id: 5 00a075 103057c08 Firmware Version: 0006 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jan 5 21:53:57 2021 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 595) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 9) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 18985 SMART Error Log Version: 1 Warning: ATA error count 0 inconsistent with error log pointer 2 ATA Error Count: 0 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 0 occurred at disk power-on lifetime: 23111 hours (962 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 20 a0 ed 2c 40 Error: ABRT at LBA = 0x002ceda0 = 2944416 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 00 20 a0 ed 2c 40 08 18d+11:27:01.376 WRITE FPDMA QUEUED e7 00 00 00 00 00 a0 08 18d+11:27:01.376 FLUSH CACHE 61 00 08 e0 34 ce 40 08 18d+11:27:01.376 WRITE FPDMA QUEUED 61 00 08 d0 34 ce 40 08 18d+11:27:01.376 WRITE FPDMA QUEUED 61 00 08 48 34 ce 40 08 18d+11:27:01.376 WRITE FPDMA QUEUED Error -1 occurred at disk power-on lifetime: 23106 hours (962 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 50 08 28 6e ab 40 at LBA = 0x00ab6e28 = 11234856 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 28 6e ab 40 08 18d+06:57:01.376 READ FPDMA QUEUED e7 00 00 00 00 00 a0 08 18d+06:57:01.376 FLUSH CACHE 61 00 08 40 72 24 40 08 18d+06:57:01.376 WRITE FPDMA QUEUED 61 00 08 e0 76 45 40 08 18d+06:57:01.376 WRITE FPDMA QUEUED e7 00 00 00 00 00 a0 08 18d+06:57:01.376 FLUSH CACHE Error -2 occurred at disk power-on lifetime: 23106 hours (962 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 50 08 28 6e ab 40 at LBA = 0x00ab6e28 = 11234856 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 28 6e ab 40 08 18d+06:57:01.376 READ FPDMA QUEUED 60 00 08 18 6e ab 40 08 18d+06:57:01.376 READ FPDMA QUEUED 60 00 08 d8 6d ab 40 08 18d+06:57:01.376 READ FPDMA QUEUED e7 00 00 00 00 00 a0 08 18d+06:57:01.376 FLUSH CACHE 61 00 08 10 6b 45 40 08 18d+06:57:01.376 WRITE FPDMA QUEUED Error -3 occurred at disk power-on lifetime: 23106 hours (962 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 50 00 28 6e ab 40 at LBA = 0x00ab6e28 = 11234856 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 60 6d ab 40 08 18d+06:57:01.376 READ FPDMA QUEUED 60 00 58 20 38 17 40 08 18d+06:57:01.376 READ FPDMA QUEUED 60 00 c8 88 60 ab 40 08 18d+06:57:01.376 READ FPDMA QUEUED 60 00 20 00 38 17 40 08 18d+06:57:01.376 READ FPDMA QUEUED 60 00 00 60 6c ab 40 08 18d+06:57:01.376 READ FPDMA QUEUED Error -4 occurred at disk power-on lifetime: 23106 hours (962 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 50 08 28 6e ab 40 at LBA = 0x00ab6e28 = 11234856 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 28 6e ab 40 08 18d+06:57:01.376 READ FPDMA QUEUED 61 00 18 80 6c 01 40 08 18d+06:57:01.376 WRITE FPDMA QUEUED 61 00 a8 00 08 83 40 08 18d+06:57:01.376 WRITE FPDMA QUEUED 61 00 f8 40 18 83 40 08 18d+06:57:01.376 WRITE FPDMA QUEUED 61 00 98 a8 08 83 40 08 18d+06:57:01.376 WRITE FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 23125 - # 2 Short offline Completed without error 00% 23125 - # 3 Short offline Completed without error 00% 23116 - # 4 Short offline Completed without error 00% 23108 - # 5 Extended offline Completed: read failure 90% 22876 4488760 # 6 Short offline Completed: read failure 90% 22876 4488760 # 7 Short offline Completed: read failure 90% 22876 4488760 # 8 Short offline Completed: read failure 90% 22876 4488760 # 9 Vendor (0xff) Completed without error 00% 20260 - #10 Vendor (0xff) Completed without error 00% 16775 - #11 Extended offline Completed without error 00% 16758 - #12 Vendor (0xff) Completed without error 00% 14068 - #13 Vendor (0xff) Completed without error 00% 11767 - #14 Vendor (0xff) Completed without error 00% 11646 - #15 Short offline Completed without error 00% 11598 - #16 Vendor (0xff) Completed without error 00% 11523 - #17 Vendor (0xff) Completed without error 00% 8725 - #18 Vendor (0xff) Completed without error 00% 8719 - #19 Vendor (0xff) Completed without error 00% 8649 - #20 Vendor (0xff) Completed without error 00% 8625 - #21 Vendor (0xff) Completed without error 00% 8611 - 4 of 4 failed self-tests are outdated by newer successful extended offline self-test # 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
Wie man sieht gibt es hier einige Errors und das "eigentliche" Ergebnis zeigt auch nur eine Zeile an, die des Power_Cycle_Count. Dazu muss ich sagen, dass meine SSD auch nicht in der smartctl database ist (obwohl schon recht alt - Crucial C300-MTFDBAK128MAG). Habe direkt dort mal ein Ticket erstellt. Kann man anhand der Ausgabe überhaupt etwas über den Zustand sagen? Wenn ich sage, dass die seit mindestens 5 Jahren jeden Tag mehrere Stunden im Betrieb ist,kann man sicherlich auch nicht mehr sagen, stimmts?