marant-
Anmeldungsdatum: 13. September 2021
Beiträge: 363
|
Was kommt als Fehlermeldung? Probiere mal so: arecord --device="hw:0,2" -V mono -v -f cd -c 1 -t raw | lame -r -b 192 - ~/mic_test.mp3 Das ist schon seltsam: Simple mixer control 'Mic Boost',0
Capabilities: volume
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 4
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB] Im alsamixer steht das auf 100%. Davon mal abgesehen, das Line Boost u. Mic Boost im amixer nur jew. 1* vorh. ist. – Wie wäre es mit einer Aktualisierung auf 20.04 ?
|
buzz_lightzyear
(Themenstarter)
Anmeldungsdatum: 8. Juni 2008
Beiträge: 422
|
Wenn ich arecord --device="hw:0,0" -V mono -v -f cd -c 1 -t raw | lame -r -b 192 - ~/mic_test.mp3 eingebe bekomme ich: arecord: main:788: audio open error: Device or resource busy
WARNING: libsndfile may ignore -r and perform fseek's on the input.
Compile without libsndfile if this is a problem.
Assuming raw pcm input file
LAME 3.100 64bits (http://lame.sf.net)
Using polyphase lowpass filter, transition band: 18671 Hz - 19205 Hz
Encoding <stdin> to /home/binder/mic_test.mp3
Encoding as 44.1 kHz j-stereo MPEG-1 Layer III (7.3x) 192 kbps qval=3
Da lese ich einen Fehler raus, darum hier die Ausgabe von arecord -l: **** List of CAPTURE Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: CX20632 Analog [CX20632 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 2: CX20632 Alt Analog [CX20632 Alt Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0 Hier der Output von
arecord --device="hw:0,2" -V mono -v -f cd -c 1 -t raw | lame -r -b 192 - ~/mic_test.mp3
Recording raw data 'stdin' : Signed 16 bit Little Endian, Rate 44100 Hz, Mono
arecord: set_params:1305: Channels count non available
WARNING: libsndfile may ignore -r and perform fseek's on the input.
Compile without libsndfile if this is a problem.
Assuming raw pcm input file
LAME 3.100 64bits (http://lame.sf.net)
Using polyphase lowpass filter, transition band: 18671 Hz - 19205 Hz
Encoding <stdin> to /home/binder/mic_test.mp3
Encoding as 44.1 kHz j-stereo MPEG-1 Layer III (7.3x) 192 kbps qval=3 Hm... hier zumindest mal kein Fehler... Danke & Lg
|
marant-
Anmeldungsdatum: 13. September 2021
Beiträge: 363
|
arecord: set_params:1305: Channels count non available Das probieren arecord --device="hw:0,2" -V mono -v -f cd -c 2 -t raw | lame -r -b 192 - ~/mic_test.mp3
|
buzz_lightzyear
(Themenstarter)
Anmeldungsdatum: 8. Juni 2008
Beiträge: 422
|
Danke, hier der Output: Recording raw data 'stdin' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
Hardware PCM card 0 'HDA Intel PCH' device 2 subdevice 0
Its setup is:
stream : CAPTURE
access : RW_INTERLEAVED
format : S16_LE
subformat : STD
channels : 2
rate : 44100
exact rate : 44100 (44100/1)
msbits : 16
buffer_size : 16384
period_size : 4096
period_time : 92879
tstamp_mode : NONE
tstamp_type : MONOTONIC
period_step : 1
avail_min : 4096
period_event : 0
start_threshold : 1
stop_threshold : 16384
silence_threshold: 0
silence_size : 0
boundary : 4611686018427387904
appl_ptr : 0
hw_ptr : 0
#+ | 00%
#+ | 00%
#+ | 00%
#+ | 00%
#+ | 00%
#+ | 00%
#+ | 00%
#+ | 00%
#+ | 00%
Standardmäßig hat er einmal "#+ | 00%" angezeigt, die anderen folgte mit drücken der Returntaste. Lg ☺
|
marant-
Anmeldungsdatum: 13. September 2021
Beiträge: 363
|
Die Fehlermeldung von dem ersten sieht eigentlich Ok aus
arecord --device="hw:0,0" -V mono -v -f cd -c 1 -t raw | lame -r -b 192 - ~/mic_test.mp3
arecord: main:788: audio open error: Device or resource busy
War wohl von PA z.Zt. belegt. Etwas warten, keine Soundeingabe/ausgabe machen und dann wierdeholen, vllt 30s. arecord --device="hw:0,0" -V mono -v -f cd -c 1 -t raw | lame -r -b 192 - ~/mic_test.mp3
arecord --device="hw:0,0" -V mono -v -f cd -c 2 -t raw | lame -r -b 192 - ~/mic_test.mp3
|
marant-
Anmeldungsdatum: 13. September 2021
Beiträge: 363
|
Danke, hier der Output:
Ist in der mp3 was drin? Du machst hoffentlich schön Krach, wenn Der aufnimmt?
|
buzz_lightzyear
(Themenstarter)
Anmeldungsdatum: 8. Juni 2008
Beiträge: 422
|
Nichts nein. Also ich puste ins Mikrofon und klatsche. (Bin in der Arbeit, da will ich mein Gesangstalent nicht vorführen 😀 ) lg
|
marant-
Anmeldungsdatum: 13. September 2021
Beiträge: 363
|
Nichts nein. Also ich puste ins Mikrofon und klatsche. (Bin in der Arbeit, da will ich mein Gesangstalent nicht vorführen 😀 )
Kommt auf Dein Alter an. 🤣 Poste mal bitte pulsemixer --list-sources (pulsemixer installieren) Ok, ich fasse die Tests mal zusammen, welche nun laufen sollten arecord --device="hw:0,0" -V mono -v -f cd -c 2 -t raw | lame -r -b 192 - ~/mic_test.mp3
arecord --device="hw:0,2" -V mono -v -f cd -c 2 -t raw | lame -r -b 192 - ~/mic_test.mp3
arecord -f dat ~/mic_test.mp3 Abbruch mit ctrl-c Der Letztere läuft über PA. Wenn bei Keinem in der mp3(wird bei jed. Test überschrieben) etwas zu hören ist weiß ich auch nicht weiter.
|
buzz_lightzyear
(Themenstarter)
Anmeldungsdatum: 8. Juni 2008
Beiträge: 422
|
Output von:
arecord --device="hw:0,0" -V mono -v -f cd -c 1 -t raw | lame -r -b 192 - ~/mic_test.mp3
–-
arecord: main:788: audio open error: Device or resource busy
WARNING: libsndfile may ignore -r and perform fseek's on the input.
Compile without libsndfile if this is a problem.
Assuming raw pcm input file
LAME 3.100 64bits (http://lame.sf.net)
Using polyphase lowpass filter, transition band: 18671 Hz - 19205 Hz
Encoding <stdin> to /home/binder/mic_test.mp3
Encoding as 44.1 kHz j-stereo MPEG-1 Layer III (7.3x) 192 kbps qval=3 Output von:
arecord --device="hw:0,0" -V mono -v -f cd -c 2 -t raw | lame -r -b 192 - ~/mic_test.mp3
–- arecord: main:788: audio open error: Device or resource busy
WARNING: libsndfile may ignore -r and perform fseek's on the input.
Compile without libsndfile if this is a problem.
Assuming raw pcm input file
LAME 3.100 64bits (http://lame.sf.net)
Using polyphase lowpass filter, transition band: 18671 Hz - 19205 Hz
Encoding <stdin> to /home/binder/mic_test.mp3
Encoding as 44.1 kHz j-stereo MPEG-1 Layer III (7.3x) 192 kbps qval=3
|
buzz_lightzyear
(Themenstarter)
Anmeldungsdatum: 8. Juni 2008
Beiträge: 422
|
pulsemixer --list sources: Source output: ID: 19, Name: Loopback to Built-in Audio Analog Stereo, Mute: 0, Channels: 2, Volumes: ['100%', '100%']
Source: ID: 1, Name: Built-in Audio Analog Stereo, Mute: 0, Channels: 2, Volumes: ['100%', '100%']
Source: ID: 5, Name: Monitor of Built-in Audio Analog Stereo, Mute: 0, Channels: 2, Volumes: ['43%', '43%']
|
Kellerkind_2009
Anmeldungsdatum: 26. November 2009
Beiträge: 19610
Wohnort: Schleswig-Holstein
|
Zeige mal pacmd info | egrep "active profile:" sowie pacmd info | grep -i "active port: \|*"
|
buzz_lightzyear
(Themenstarter)
Anmeldungsdatum: 8. Juni 2008
Beiträge: 422
|
pacmd info | egrep "active profile:" active profile: <output:analog-stereo+input:analog-stereo> pacmd info | grep -i "active port: \|*"
* index: 4
active port: <analog-output-lineout>
* index: 1
active port: <analog-input-linein> Danke ☺
|
marant-
Anmeldungsdatum: 13. September 2021
Beiträge: 363
|
loopback doch noch aktiv, ausführen
pactl unload-module module-loopback
pacmd info | egrep "active profile:"
Kannst auch nachsehen bei pavucontrol -t 5 und Ausgang+Eingang wählen Servus @Kellerkind
|
Kellerkind_2009
Anmeldungsdatum: 26. November 2009
Beiträge: 19610
Wohnort: Schleswig-Holstein
|
Das Problem active port: <analog-input-linein> sollte so aussehen active port: <analog-input-front-mic> Stelle mal um.Zeige dann wieder die Abfragen. Servus @ marant- 😉
|
marant-
Anmeldungsdatum: 13. September 2021
Beiträge: 363
|
Hat er doch nicht, wenn überhaupt dann "rear".
|