ich nutze ein acer notrebook, monitor: 15.6 HD Acer CineCrystal LED LCD.
Dann schau ich mal ob sich unter dem WIKI eintrag was tut ... danke ich meld mich sobald ich was neues weiss
Ja die Auflösung ist die richtige ...
Hab mir die wiki Anleitung ausgedruckt, steig da aber noch nicht wirklich durch.
wenn es dir keine zu großen umstände macht, kannst du mir die zeile die ich in die xorg einfügen muss nennen, natürlich probier ichs bis dahin selbst, danke ! sorry wegen irgendwelchen text und formatierungsfehlern, ich erkenn nur hier kaum was = )
edit:
Also neuster Stand, ich habe meine Modeline Rausgefunden
Modeline "1366x768" 69,500 1366 1414 1446 1437 768 771 775 806 -hsync -vsync
hab ich dann in der /etc/X11/xorg.conf so eingegeben
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# Note that some configuration settings that could be done previously
# in this file, now are automatically configured by the server and settings
# here are ignored.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "Monitor"
Identifier "Configured Monitor"
ModeLine "1366x768" 69,5 1366 1414 1446 1437 768 771 775 806
EndSection
Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1366x768"
EndSubSection
EndSection
Section "Module"
Load "glx"
EndSection
Section "Device"
Identifier "Configured Video Device"
Driver "nvidia"
Option "NoLogo" "True"
EndSection
Code
Nach nem neustart, wollte er die einstellung aber nicht nehmen, und hatt
gemeint irgendweas von running in low grafic mode
gab dann grafisch ein paar optionen, da hab ich dann geschafft den treiber wieder zu deaktivieren
und die standart xorg.conf wieder einzufügen und jetzt hab ich keinen treiber mehr, aber keine
fenster mehr und ne normale auflösung.
Ist ein Fehler in der Xorg ?
Hab hier noch was nachgelesen, kann das weiter helfen ?
Acer
Acer AT4220B / AT3720B / AT3220B / AT2720B
These screens supports 1366x768 on both the VGA input and HDMI input but the EDID data does not do this correctly. (using xorg 7.2) I have the 37" version, but I guess the electronics is the same in the whole range. Native resolution is 1366x768. Running the screen at 1368x768 will result in a little line running up the image from time to time. 1360x768 is much better, but scene changes flicker a bit some times. My 7100 nvidia card can't do the 1366x768 resolution and I'm guessing that would fix the issue.
Device section:
# Option "ExactModeTimingsDVI"
# Option "ModeValidation" "NoDFPNativeResolutionCheck"
Monitor section:
SubSection "Display"
Modes "1360x768"
Allerneuster Stand:
Habe die Xorg config geändert siehe dieses Forum http://www.nvnews.net/vbulletin/showthread.php?s=fc9ff99c39a32a85ca44cfb97ba43806&t=132041&highlight=G105M+Linux&page=2
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# Note that some configuration settings that could be done previously
# in this file, now are automatically configured by the server and settings
# here are ignored.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "InputDevice"
Identifier "TouchPad"
Driver "synaptics"
Option "device" "/dev/input/event8"
# Option "TapButton1" "0"
# Option "TapButton2" "0"
Option "HorizEdgeScroll" "False"
Option "VertTwoFingerScroll" "True"
Option "HorizTowFingerScroll" "True"
# Option "TouchpadOff" "2"
Option "SHMConfig" "False"
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
# InputDevice "Mouse0" "CorePointer"
InputDevice "TouchPad" "CorePinter"
EndSection
Section "ServerFlags"
Option "Xinerama" "0"
Option "AIGLX" "False"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
#Section "InputDevice"
# # generated from default
# Identifier "Mouse0"
# Driver "mouse"
# Option "Protocol" "auto"
# Option "Device" "/dev/psaux"
# Option "Emulate3Buttons" "no"
# Option "ZAxisMapping" "4 5"
#EndSection
Section "Monitor"
Identifier "Configured Monitor"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "AUO"
# HorizSync 30.0 - 100.0
# VertRefresh 55.0 - 110.0
DisplaySize 344 193
# Mode "1366x768"
# DotClock 69.5MHz
# HTimings 1366 1414 1446 1437
# VTimings 768 771 775 806
# EndMode
# Modeline "1366x768" 69.50 1366 1414 1446 1437 768 771 775 806
Modeline "1366x768" 69.50 1366 1414 1446 1446 768 771 775 806 -hsync -vsync
# Modeline "1366x768q" 72.00 1366 1414 1446 1494 768 771 777 803 -hsync -vsync
# Option "DPMS" "True"
EndSection
#Section "Device"
# Identifier "Configured Video Device"
# Driver "nvidia"
#EndSection
Section "Device"
Identifier "Device0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce G 105M"
Option "NvAGP" "0"
# Option "UseInt10Module" "True"
Option "UseEDID" "False"
Option "AllowSHMPixmaps" "True"
Option "ExactModeTimingsDVI" "True"
Option "ModeValidation" "NoHorizSyncCheck,NoDFPNativeResolutionCheck,NoExtendedGpuCapabilitiesCheck,NoWidthAlignmentCheck,NoVertRefreshCheck"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "Configured Video Device"
Monitor "Configured Monitor"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
Option "TwinView" "0"
SubSection "Display"
Modes "1366x768"
Depth 24
EndSubSection
EndSection
Code
UnD es scheint alles zu funktionieren !!! JUHU!