Habe smartmontools installiert.
Der Suchlauf sollte vor einer Stunde fertig sein, jetzt habe ich ihn abgebrochen.
Er ergab:
iri@kiri-GA-A75M-UD2H:~$ sudo smartctl -x /dev/sdc #Status der ersten SATA-Platte ermitteln
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.13.0-43-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi/HGST Travelstar Z7K500
Device Model: HGST HTS725050A7E630
Serial Number: RCF50ACE1HV54M
LU WWN Device Id: 5 000cca 85ed54b4b
Firmware Version: GS2OA340
User Capacity: 500.107.862.016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Jun 8 13:49:59 2018 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Unknown
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 45) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 90) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 062 - 0
2 Throughput_Performance P-S--K 100 100 040 - 0
3 Spin_Up_Time PO---K 245 100 033 - 1
4 Start_Stop_Count -O--CK 100 100 000 - 566
5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
7 Seek_Error_Rate POSR-K 100 100 067 - 0
8 Seek_Time_Performance P-S--K 100 100 040 - 0
9 Power_On_Hours -O--CK 100 100 000 - 277
10 Spin_Retry_Count PO--CK 100 100 060 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 417
183 Runtime_Bad_Block -O--CK 100 100 001 - 0
184 End-to-End_Error PO--CK 100 100 097 - 0
187 Reported_Uncorrect -O--CK 100 001 000 - 111
188 Command_Timeout -O--CK 100 069 000 - 6970838286380
190 Airflow_Temperature_Cel -O---K 069 061 045 - 31 (Min/Max 21/39)
191 G-Sense_Error_Rate -O--CK 100 100 000 - 5
192 Power-Off_Retract_Count -O--CK 100 100 000 - 3276850
193 Load_Cycle_Count -O--CK 096 096 000 - 48158
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
197 Current_Pending_Sector -O--CK 100 100 000 - 0
198 Offline_Uncorrectable ----CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0
223 Load_Retry_Count -O-R-K 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 111 (device log contains only the most recent 4 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 111 [2] occurred at disk power-on lifetime: 76 hours (3 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 41 01 70 00 00 11 fd 08 80 01 00 Error: IDNF at LBA = 0x11fd0880 = 301795456
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 04 00 00 08 00 00 11 fd 44 00 40 00 01:19:59.991 WRITE FPDMA QUEUED
61 04 00 00 00 00 00 11 fd 40 00 40 00 01:19:59.991 WRITE FPDMA QUEUED
61 04 00 00 58 00 00 11 fd 3c 00 40 00 01:19:59.990 WRITE FPDMA QUEUED
61 04 00 00 50 00 00 11 fd 38 00 40 00 01:19:59.988 WRITE FPDMA QUEUED
61 04 00 00 48 00 00 11 fd 34 00 40 00 01:19:59.985 WRITE FPDMA QUEUED
Error 110 [1] occurred at disk power-on lifetime: 76 hours (3 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 41 04 00 00 00 11 fb 08 00 01 00 Error: IDNF at LBA = 0x11fb0800 = 301664256
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 04 00 00 58 00 00 11 fc 78 00 40 00 01:19:28.827 WRITE FPDMA QUEUED
61 04 00 00 50 00 00 11 fc 74 00 40 00 01:19:28.826 WRITE FPDMA QUEUED
61 04 00 00 48 00 00 11 fc 70 00 40 00 01:19:28.824 WRITE FPDMA QUEUED
61 04 00 00 40 00 00 11 fc 6c 00 40 00 01:19:28.823 WRITE FPDMA QUEUED
61 04 00 00 38 00 00 11 fc 68 00 40 00 01:19:28.822 WRITE FPDMA QUEUED
Error 109 [0] occurred at disk power-on lifetime: 76 hours (3 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 41 03 90 00 00 11 fb 90 70 01 00 Error: IDNF at LBA = 0x11fb9070 = 301699184
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 04 00 00 40 00 00 11 fb bc 00 40 00 01:18:57.853 WRITE FPDMA QUEUED
61 04 00 00 38 00 00 11 fb b8 00 40 00 01:18:57.850 WRITE FPDMA QUEUED
61 04 00 00 30 00 00 11 fb b4 00 40 00 01:18:57.845 WRITE FPDMA QUEUED
61 04 00 00 28 00 00 11 fb b0 00 40 00 01:18:57.839 WRITE FPDMA QUEUED
61 04 00 00 20 00 00 11 fb ac 00 40 00 01:18:57.838 WRITE FPDMA QUEUED
Error 108 [3] occurred at disk power-on lifetime: 76 hours (3 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 41 04 00 00 00 11 f9 58 00 01 00 Error: IDNF at LBA = 0x11f95800 = 301553664
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 04 00 00 10 00 00 11 f9 90 00 40 00 01:18:26.768 WRITE FPDMA QUEUED
61 04 00 00 08 00 00 11 f9 8c 00 40 00 01:18:26.764 WRITE FPDMA QUEUED
61 04 00 00 00 00 00 11 f9 88 00 40 00 01:18:26.764 WRITE FPDMA QUEUED
61 04 00 00 58 00 00 11 f9 84 00 40 00 01:18:26.763 WRITE FPDMA QUEUED
61 04 00 00 50 00 00 11 f9 80 00 40 00 01:18:26.761 WRITE FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 276 -
# 2 Short offline Completed without error 00% 13 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 31 Celsius
Power Cycle Min/Max Temperature: 21/39 Celsius
Lifetime Min/Max Temperature: 13/39 Celsius
Lifetime Average Temperature: 27 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -40/65 Celsius
Temperature History Size (Index): 128 (38)
Index Estimated Time Temperature Celsius
39 2018-06-08 11:43 39 ********************
... ..( 58 skipped). .. ********************
98 2018-06-08 12:42 39 ********************
99 2018-06-08 12:43 38 *******************
100 2018-06-08 12:44 37 ******************
101 2018-06-08 12:45 37 ******************
102 2018-06-08 12:46 36 *****************
103 2018-06-08 12:47 35 ****************
104 2018-06-08 12:48 35 ****************
105 2018-06-08 12:49 34 ***************
106 2018-06-08 12:50 34 ***************
107 2018-06-08 12:51 33 **************
... ..( 2 skipped). .. **************
110 2018-06-08 12:54 33 **************
111 2018-06-08 12:55 32 *************
... ..( 5 skipped). .. *************
117 2018-06-08 13:01 32 *************
118 2018-06-08 13:02 31 ************
... ..( 47 skipped). .. ************
38 2018-06-08 13:50 31 ************
SMART WRITE LOG does not return COUNT and LBA_LOW register
SCT (Get) Error Recovery Control command failed
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 0 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
Ist trotz des Abbruchs eine Interpretation zum Zustand der externen Festplatte möglich? sdc ist die ex. Festplatte!