Kuchipatchi
Anmeldungsdatum: 13. Oktober 2009
Beiträge: 31
Wohnort: Koblenz
|
Hallo Ihr Lieben! Ich habe mal das Forum ein wenig durchsucht bin aber nicht wirklich fündig geworden!
Ich habe einen avertv volar black hd Stick. Ich habe Ihn nach dieser Anleitung installiert: http://wiki.ubuntuusers.de/v4l-dvb Der Tv Stick wird dannach auch bei der Ausgabe lsusb als "Bus 001 Device 002: ID 07ca:850a AVerMedia Technologies, Inc." erkannt. In Kaffeine wird der Stick auch erkannt und eingerichtet. Nur bei der Sendersuche habe ich keinen Erfolg.
Folgende Fragen tun sich mir jetzt auf. 1. Habe ich den Stick richtig installiert?
2. Warum bekomme ich mit TVTime den Stick nicht angezeigt?
3. Weis einer wie Ich Sender finde kann bzw. wo in der Konfiguration noch Fehler sein könnten? Achja habs auch hiermit versucht: http://forum.ubuntuusers.de/topic/avertv-volar-black-hd-a850a-dvb-stick/#post-1768576 Aber auch hier nur Erkennung des Sticks und keine Sender. Achja das hier DVB-t vorhanden ist erklärt sich ja von selbst 😀
Das habe ich natürlich schon überprüft. Wohne ja direkt in der Stadt! Wenn sich einer mit dem Thema beschäftigen würde, wäre ich sehr dankbar. Gruß Leon
|
eishailiga
Anmeldungsdatum: 31. Oktober 2006
Beiträge: 5401
Wohnort: Sauerland
|
Poste mal die Ausgabe von
dmesg | grep -i dvb
|
Kuchipatchi
(Themenstarter)
Anmeldungsdatum: 13. Oktober 2009
Beiträge: 31
Wohnort: Koblenz
|
Also laut dmesg ist der Stick erkannt und funktioniert kuchiptachi@kuchiptachi-desktop:~$ dmesg | grep -i dvb
[ 9.332528] dvb-usb: found a 'AverMedia AVerTV Volar Black HD (A850)' in warm state.
[ 9.332585] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 9.332916] DVB: registering new adapter (AverMedia AVerTV Volar Black HD (A850))
[ 9.576520] DVB: registering adapter 0 frontend 0 (Afatech AF9013 DVB-T)...
[ 9.606866] dvb-usb: AverMedia AVerTV Volar Black HD (A850) successfully initialized and connected.
[ 9.612539] usbcore: registered new interface driver dvb_usb_af9015
kuchiptachi@kuchiptachi-desktop:~$
Ich habe es jetzt auch einmal hinbekommen bei Kaffeine Sender zu finden und auch zu schauen.
Das hat aber nicht lange angehlten.
Immer wenn ich jetzt einen Sender starten möchte bekomme ich die Meldung " DVB kann nicht eingestellt werden ☹ Gruß LEon
|
eishailiga
Anmeldungsdatum: 31. Oktober 2006
Beiträge: 5401
Wohnort: Sauerland
|
Starte doch Kaffeine mal aus der Konsole und wenn obiger Fehler erscheint, poste den Inhalt aus dieser Konsole...
kaffeine -verbose
|
Kuchipatchi
(Themenstarter)
Anmeldungsdatum: 13. Oktober 2009
Beiträge: 31
Wohnort: Koblenz
|
Hey Eishailiga hier mal die Ausgabe kuchiptachi@kuchiptachi-desktop:~$ kaffeine -verbose
DCOPClient::attachInternal. Attach failed Could not open network socket
DCOPClient::attachInternal. Attach failed Could not open network socket
kbuildsycoca running...
/dev/dvb/adapter0/frontend0 : opened ( Afatech AF9013 DVB-T )
0 EPG plugins loaded for device 0:0.
Loaded epg data : 1416 events (30 msecs)
kuchiptachi@kuchiptachi-desktop:~$ Tuning to: ProSieben / autocount: 0
DvbCam::probe(): /dev/dvb/adapter0/ca0: : No such file or directory
Using DVB device 0:0 "Afatech AF9013 DVB-T"
tuning DVB-T to 730000000 Hz
inv:2 bw:0 fecH:9 fecL:9 mod:6 tm:2 gi:4 hier:4
..................................................
Not able to lock to the signal on the given frequency
Frontend closed
Tuning delay: 11181 ms
Tuning to: N24 / autocount: 0
Using DVB device 0:0 "Afatech AF9013 DVB-T"
tuning DVB-T to 730000000 Hz
inv:2 bw:0 fecH:9 fecL:9 mod:6 tm:2 gi:4 hier:4
..................................................
Not able to lock to the signal on the given frequency
Frontend closed
Tuning delay: 7034 ms
Kannst du damit etwas anfangen ? Gruß Leon ☺
|
eishailiga
Anmeldungsdatum: 31. Oktober 2006
Beiträge: 5401
Wohnort: Sauerland
|
Starte doch mal den Rechner neu und poste die Ausgabe von dmesg ...ich will mal sehen, welche Firmware dort geladen wird...ich vermute mal, daß es die Falsche ist...
|
Kuchipatchi
(Themenstarter)
Anmeldungsdatum: 13. Oktober 2009
Beiträge: 31
Wohnort: Koblenz
|
[ 0.372418] pci 0000:01:00.0: reg 1c 64bit mmio: [0xe4000000-0xe5ffffff]
[ 0.372422] pci 0000:01:00.0: reg 24 io port: [0xb000-0xb07f]
[ 0.372425] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x07ffff]
[ 0.372460] pci 0000:00:01.0: bridge io port: [0xb000-0xbfff]
[ 0.372462] pci 0000:00:01.0: bridge 32bit mmio: [0xe4000000-0xe7ffffff]
[ 0.372464] pci 0000:00:01.0: bridge 64bit mmio pref: [0xc0000000-0xdfffffff]
[ 0.372492] pci 0000:00:1c.0: bridge io port: [0x9000-0x9fff]
[ 0.372542] pci 0000:03:00.0: reg 10 io port: [0xc000-0xc007]
[ 0.372549] pci 0000:03:00.0: reg 14 io port: [0xc100-0xc103]
[ 0.372556] pci 0000:03:00.0: reg 18 io port: [0xc200-0xc207]
[ 0.372564] pci 0000:03:00.0: reg 1c io port: [0xc300-0xc303]
[ 0.372571] pci 0000:03:00.0: reg 20 io port: [0xc400-0xc40f]
[ 0.372627] pci 0000:00:1c.3: bridge io port: [0xc000-0xcfff]
[ 0.372630] pci 0000:00:1c.3: bridge 32bit mmio: [0xe8000000-0xe8ffffff]
[ 0.372679] pci 0000:04:00.0: reg 10 io port: [0xd000-0xd0ff]
[ 0.372698] pci 0000:04:00.0: reg 18 64bit mmio: [0xea000000-0xea000fff]
[ 0.372716] pci 0000:04:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 0.372726] pci 0000:04:00.0: supports D1 D2
[ 0.372727] pci 0000:04:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.372731] pci 0000:04:00.0: PME# disabled
[ 0.372767] pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff]
[ 0.372769] pci 0000:00:1c.4: bridge 32bit mmio: [0xe9000000-0xeaffffff]
[ 0.372808] pci 0000:00:1e.0: transparent bridge
[ 0.372810] pci 0000:00:1e.0: bridge io port: [0xa000-0xafff]
[ 0.372829] bus 00 -> node 0
[ 0.372833] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.372985] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 0.373051] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
[ 0.373118] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[ 0.373183] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.384339] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.384417] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.384494] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[ 0.384570] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.384646] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.384722] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.384797] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[ 0.384872] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.385008] ACPI: WMI: Mapper loaded
[ 0.385052] SCSI subsystem initialized
[ 0.385052] libata version 3.00 loaded.
[ 0.385052] usbcore: registered new interface driver usbfs
[ 0.385052] usbcore: registered new interface driver hub
[ 0.385052] usbcore: registered new device driver usb
[ 0.385052] PCI: Using ACPI for IRQ routing
[ 0.396008] Bluetooth: Core ver 2.13
[ 0.396019] NET: Registered protocol family 31
[ 0.396019] Bluetooth: HCI device and connection manager initialized
[ 0.396019] Bluetooth: HCI socket layer initialized
[ 0.396020] NET: Registered protocol family 8
[ 0.396021] NET: Registered protocol family 20
[ 0.396030] NetLabel: Initializing
[ 0.396032] NetLabel: domain hash size = 128
[ 0.396033] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.396044] NetLabel: unlabeled traffic allowed by default
[ 0.396069] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.396073] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 0.400058] AppArmor: AppArmor Filesystem Enabled
[ 0.412008] pnp: PnP ACPI init
[ 0.412015] ACPI: bus type pnp registered
[ 0.414037] pnp: PnP ACPI: found 15 devices
[ 0.414038] ACPI: ACPI bus type pnp unregistered
[ 0.414044] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 0.414045] system 00:01: ioport range 0x290-0x29f has been reserved
[ 0.414047] system 00:01: ioport range 0x800-0x87f has been reserved
[ 0.414048] system 00:01: ioport range 0x290-0x294 has been reserved
[ 0.414049] system 00:01: ioport range 0x880-0x88f has been reserved
[ 0.414054] system 00:0b: ioport range 0x400-0x4bf could not be reserved
[ 0.414057] system 00:0c: iomem range 0xe0000000-0xe3ffffff has been reserved
[ 0.414061] system 00:0d: iomem range 0xce200-0xcffff has been reserved
[ 0.414062] system 00:0d: iomem range 0xf0000-0xf7fff could not be reserved
[ 0.414064] system 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.414065] system 00:0d: iomem range 0xfc000-0xfffff could not be reserved
[ 0.414067] system 00:0d: iomem range 0xbfee0000-0xbfefffff could not be reserved
[ 0.414068] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 0.414069] system 00:0d: iomem range 0x100000-0xbfedffff could not be reserved
[ 0.414071] system 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.414072] system 00:0d: iomem range 0xfed10000-0xfed1dfff has been reserved
[ 0.414075] system 00:0d: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 0.414076] system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.414078] system 00:0d: iomem range 0xffb00000-0xffb7ffff has been reserved
[ 0.414079] system 00:0d: iomem range 0xfff00000-0xffffffff has been reserved
[ 0.414080] system 00:0d: iomem range 0xe0000-0xeffff has been reserved
[ 0.418682] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.418684] pci 0000:00:01.0: IO window: 0xb000-0xbfff
[ 0.418686] pci 0000:00:01.0: MEM window: 0xe4000000-0xe7ffffff
[ 0.418688] pci 0000:00:01.0: PREFETCH window: 0x000000c0000000-0x000000dfffffff
[ 0.418690] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.418692] pci 0000:00:1c.0: IO window: 0x9000-0x9fff
[ 0.418695] pci 0000:00:1c.0: MEM window: disabled
[ 0.418697] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.418701] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:03
[ 0.418703] pci 0000:00:1c.3: IO window: 0xc000-0xcfff
[ 0.418706] pci 0000:00:1c.3: MEM window: 0xe8000000-0xe8ffffff
[ 0.418708] pci 0000:00:1c.3: PREFETCH window: disabled
[ 0.418712] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:04
[ 0.418714] pci 0000:00:1c.4: IO window: 0xd000-0xdfff
[ 0.418717] pci 0000:00:1c.4: MEM window: 0xe9000000-0xeaffffff
[ 0.418719] pci 0000:00:1c.4: PREFETCH window: 0x000000eb100000-0x000000eb1fffff
[ 0.418723] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[ 0.418725] pci 0000:00:1e.0: IO window: 0xa000-0xafff
[ 0.418728] pci 0000:00:1e.0: MEM window: disabled
[ 0.418730] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.418738] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.418741] pci 0000:00:01.0: setting latency timer to 64
[ 0.418745] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.418747] pci 0000:00:1c.0: setting latency timer to 64
[ 0.418752] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.418755] pci 0000:00:1c.3: setting latency timer to 64
[ 0.418759] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.418761] pci 0000:00:1c.4: setting latency timer to 64
[ 0.418766] pci 0000:00:1e.0: setting latency timer to 64
[ 0.418768] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.418769] bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff]
[ 0.418770] bus: 01 index 0 io port: [0xb000-0xbfff]
[ 0.418771] bus: 01 index 1 mmio: [0xe4000000-0xe7ffffff]
[ 0.418772] bus: 01 index 2 mmio: [0xc0000000-0xdfffffff]
[ 0.418773] bus: 01 index 3 mmio: [0x0-0x0]
[ 0.418774] bus: 02 index 0 io port: [0x9000-0x9fff]
[ 0.418775] bus: 02 index 1 mmio: [0x0-0x0]
[ 0.418776] bus: 02 index 2 mmio: [0x0-0x0]
[ 0.418777] bus: 02 index 3 mmio: [0x0-0x0]
[ 0.418778] bus: 03 index 0 io port: [0xc000-0xcfff]
[ 0.418779] bus: 03 index 1 mmio: [0xe8000000-0xe8ffffff]
[ 0.418780] bus: 03 index 2 mmio: [0x0-0x0]
[ 0.418781] bus: 03 index 3 mmio: [0x0-0x0]
[ 0.418782] bus: 04 index 0 io port: [0xd000-0xdfff]
[ 0.418783] bus: 04 index 1 mmio: [0xe9000000-0xeaffffff]
[ 0.418784] bus: 04 index 2 mmio: [0xeb100000-0xeb1fffff]
[ 0.418785] bus: 04 index 3 mmio: [0x0-0x0]
[ 0.418786] bus: 05 index 0 io port: [0xa000-0xafff]
[ 0.418787] bus: 05 index 1 mmio: [0x0-0x0]
[ 0.418788] bus: 05 index 2 mmio: [0x0-0x0]
[ 0.418789] bus: 05 index 3 io port: [0x00-0xffff]
[ 0.418790] bus: 05 index 4 mmio: [0x000000-0xffffffffffffffff]
[ 0.418795] NET: Registered protocol family 2
[ 0.452049] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.452278] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.453122] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.453375] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.453377] TCP reno registered
[ 0.464083] NET: Registered protocol family 1
[ 0.464175] checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
[ 0.504004] Switched to high resolution mode on CPU 0
[ 0.681542] it is
[ 0.911006] Freeing initrd memory: 7761k freed
[ 0.912901] audit: initializing netlink socket (disabled)
[ 0.912920] type=2000 audit(1255644007.912:1): initialized
[ 0.918460] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.919223] VFS: Disk quotas dquot_6.5.1
[ 0.919254] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.919602] fuse init (API version 7.10)
[ 0.919648] msgmni has been set to 7788
[ 0.919753] alg: No test for stdrng (krng)
[ 0.919759] io scheduler noop registered
[ 0.919760] io scheduler anticipatory registered
[ 0.919761] io scheduler deadline registered
[ 0.919787] io scheduler cfq registered (default)
[ 0.919907] pci 0000:01:00.0: Boot video device
[ 0.921616] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 0.921635] pcieport-driver 0000:00:01.0: found MSI capability
[ 0.921650] pcieport-driver 0000:00:01.0: irq 2303 for MSI/MSI-X
[ 0.921655] pci_express 0000:00:01.0:pcie00: allocate port service
[ 0.921663] pci_express 0000:00:01.0:pcie03: allocate port service
[ 0.921691] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.921714] pcieport-driver 0000:00:1c.0: found MSI capability
[ 0.921730] pcieport-driver 0000:00:1c.0: irq 2302 for MSI/MSI-X
[ 0.921737] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 0.921745] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 0.921754] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 0.921790] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[ 0.921813] pcieport-driver 0000:00:1c.3: found MSI capability
[ 0.921829] pcieport-driver 0000:00:1c.3: irq 2301 for MSI/MSI-X
[ 0.921836] pci_express 0000:00:1c.3:pcie00: allocate port service
[ 0.921844] pci_express 0000:00:1c.3:pcie02: allocate port service
[ 0.921851] pci_express 0000:00:1c.3:pcie03: allocate port service
[ 0.921887] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 0.921910] pcieport-driver 0000:00:1c.4: found MSI capability
[ 0.921926] pcieport-driver 0000:00:1c.4: irq 2300 for MSI/MSI-X
[ 0.921933] pci_express 0000:00:1c.4:pcie00: allocate port service
[ 0.921942] pci_express 0000:00:1c.4:pcie02: allocate port service
[ 0.921949] pci_express 0000:00:1c.4:pcie03: allocate port service
[ 0.921993] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.922188] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.922280] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.922282] ACPI: Power Button (FF) [PWRF]
[ 0.922308] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.922309] ACPI: Power Button (CM) [PWRB]
[ 0.922497] processor ACPI_CPU:00: registered as cooling_device0
[ 0.922499] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 0.922614] ACPI: SSDT BFEE8300, 0087 (r1 PmRef Cpu1Ist 3000 INTL 20040311)
[ 0.922733] processor ACPI_CPU:01: registered as cooling_device1
[ 0.922736] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 0.952651] Linux agpgart interface v0.103
[ 0.952657] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 0.952733] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.952952] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.953417] brd: module loaded
[ 0.953606] loop: module loaded
[ 0.953644] Fixed MDIO Bus: probed
[ 0.953647] PPP generic driver version 2.4.2
[ 0.953683] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.953698] Driver 'sd' needs updating - please use bus_type methods
[ 0.953703] Driver 'sr' needs updating - please use bus_type methods
[ 0.953747] ata_piix 0000:00:1f.2: version 2.12
[ 0.953755] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.953758] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[ 0.953785] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.953830] scsi0 : ata_piix
[ 0.953872] scsi1 : ata_piix
[ 0.954291] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 0.954294] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 1.428038] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.444172] ata1.00: HPA unlocked: 488395055 -> 488397168, native 488397168
[ 1.444175] ata1.00: ATA-7: SAMSUNG HD250HJ, FH100-06, max UDMA7
[ 1.444176] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.452273] ata1.00: configured for UDMA/133
[ 1.928040] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.936174] ata2.00: ATAPI: HL-DT-ST DVDRAM GH20NS10, EL00, max UDMA/100
[ 1.952182] ata2.00: configured for UDMA/100
[ 1.957574] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD250HJ FH10 PQ: 0 ANSI: 5
[ 1.957636] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 1.957647] sd 0:0:0:0: [sda] Write Protect is off
[ 1.957648] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.957664] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.957705] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 1.957714] sd 0:0:0:0: [sda] Write Protect is off
[ 1.957715] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.957730] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.957732] sda: sda1 sda2 < sda5 >
[ 1.985960] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.985984] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.989287] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GH20NS10 EL00 PQ: 0 ANSI: 5
[ 1.993120] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.993122] Uniform CD-ROM driver Revision: 3.20
[ 1.993189] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.993222] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.993234] ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.993236] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 1.993259] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 1.993292] scsi2 : ata_piix
[ 1.993324] scsi3 : ata_piix
[ 1.993673] ata3: SATA max UDMA/133 cmd 0xe700 ctl 0xe800 bmdma 0xeb00 irq 19
[ 1.993675] ata4: SATA max UDMA/133 cmd 0xe900 ctl 0xea00 bmdma 0xeb08 irq 19
[ 2.322521] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.650512] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.650705] pata_jmicron 0000:03:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 2.650723] pata_jmicron 0000:03:00.0: setting latency timer to 64
[ 2.650757] scsi4 : pata_jmicron
[ 2.650790] scsi5 : pata_jmicron
[ 2.651239] ata5: PATA max UDMA/100 cmd 0xc000 ctl 0xc100 bmdma 0xc400 irq 19
[ 2.651241] ata6: PATA max UDMA/100 cmd 0xc200 ctl 0xc300 bmdma 0xc408 irq 19
[ 2.960238] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.960250] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.960258] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 2.960260] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.960297] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 2.964206] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 2.964214] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xeb004000
[ 2.980007] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 2.980061] usb usb1: configuration #1 chosen from 1 choice
[ 2.980083] hub 1-0:1.0: USB hub found
[ 2.980089] hub 1-0:1.0: 6 ports detected
[ 2.980164] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.980169] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2.980171] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.980194] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 2.984102] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 2.984109] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xeb005000
[ 2.996007] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.996052] usb usb2: configuration #1 chosen from 1 choice
[ 2.996072] hub 2-0:1.0: USB hub found
[ 2.996077] hub 2-0:1.0: 6 ports detected
[ 2.996145] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.996154] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.996165] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.996168] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.996170] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.996194] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 2.996218] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000e100
[ 2.996260] usb usb3: configuration #1 chosen from 1 choice
[ 2.996275] hub 3-0:1.0: USB hub found
[ 2.996279] hub 3-0:1.0: 2 ports detected
[ 2.996328] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 2.996332] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 2.996334] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.996357] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 2.996379] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000e200
[ 2.996425] usb usb4: configuration #1 chosen from 1 choice
[ 2.996438] hub 4-0:1.0: USB hub found
[ 2.996441] hub 4-0:1.0: 2 ports detected
[ 2.996488] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.996491] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 2.996493] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 2.996520] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[ 2.996538] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000e000
[ 2.996580] usb usb5: configuration #1 chosen from 1 choice
[ 2.996593] hub 5-0:1.0: USB hub found
[ 2.996597] hub 5-0:1.0: 2 ports detected
[ 2.996645] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.996649] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.996650] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.996680] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 2.996697] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e300
[ 2.996739] usb usb6: configuration #1 chosen from 1 choice
[ 2.996756] hub 6-0:1.0: USB hub found
[ 2.996759] hub 6-0:1.0: 2 ports detected
[ 2.996805] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.996809] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.996811] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.996836] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 2.996854] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e400
[ 2.996896] usb usb7: configuration #1 chosen from 1 choice
[ 2.996911] hub 7-0:1.0: USB hub found
[ 2.996914] hub 7-0:1.0: 2 ports detected
[ 2.996962] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.996965] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.996967] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.996991] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 2.997009] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e500
[ 2.997052] usb usb8: configuration #1 chosen from 1 choice
[ 2.997065] hub 8-0:1.0: USB hub found
[ 2.997068] hub 8-0:1.0: 2 ports detected
[ 2.997142] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 2.997143] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 2.997188] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.008530] mice: PS/2 mouse device common for all mice
[ 3.044549] rtc_cmos 00:04: RTC can wake from S4
[ 3.044574] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 3.044595] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 3.044639] device-mapper: uevent: version 1.0.3
[ 3.044684] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 3.044727] device-mapper: multipath: version 1.0.5 loaded
[ 3.044729] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 3.044780] cpuidle: using governor ladder
[ 3.044781] cpuidle: using governor menu
[ 3.045020] TCP cubic registered
[ 3.045059] NET: Registered protocol family 10
[ 3.045295] lo: Disabled Privacy Extensions
[ 3.045460] NET: Registered protocol family 17
[ 3.045470] Bluetooth: L2CAP ver 2.11
[ 3.045471] Bluetooth: L2CAP socket layer initialized
[ 3.045473] Bluetooth: SCO (Voice Link) ver 0.6
[ 3.045474] Bluetooth: SCO socket layer initialized
[ 3.045488] Bluetooth: RFCOMM socket layer initialized
[ 3.045491] Bluetooth: RFCOMM TTY layer initialized
[ 3.045492] Bluetooth: RFCOMM ver 1.10
[ 3.047505] registered taskstats version 1
[ 3.047599] Magic number: 13:447:47
[ 3.047668] rtc_cmos 00:04: setting system clock to 2009-10-15 22:00:10 UTC (1255644010)
[ 3.047670] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 3.047671] EDD information not available.
[ 3.047695] Freeing unused kernel memory: 536k freed
[ 3.047789] Write protecting the kernel read-only data: 6688k
[ 3.070223] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 3.163047] Floppy drive(s): fd0 is 1.44M
[ 3.180321] FDC 0 is a post-1991 82077
[ 3.189118] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 3.189135] r8169 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.189153] r8169 0000:04:00.0: setting latency timer to 64
[ 3.189282] r8169 0000:04:00.0: irq 2299 for MSI/MSI-X
[ 3.189647] eth0: RTL8168b/8111b at 0xffffc2000005e000, 00:1d:7d:e9:3b:ef, XID 38000000 IRQ 2299
[ 3.292600] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 3.402517] PM: Starting manual resume from disk
[ 3.402519] PM: Resume from partition 8:5
[ 3.402520] PM: Checking hibernation image.
[ 3.402645] PM: Resume from disk failed.
[ 3.428944] usb 1-1: configuration #1 chosen from 1 choice
[ 3.433625] kjournald starting. Commit interval 5 seconds
[ 3.433631] EXT3-fs: mounted filesystem with ordered data mode.
[ 3.540508] usb 1-2: new high speed USB device using ehci_hcd and address 3
[ 3.672942] usb 1-2: configuration #1 chosen from 1 choice
[ 3.840510] usb 1-4: new high speed USB device using ehci_hcd and address 5
[ 3.972928] usb 1-4: configuration #1 chosen from 1 choice
[ 4.212012] usb 4-1: new low speed USB device using uhci_hcd and address 2
[ 4.385439] usb 4-1: configuration #1 chosen from 1 choice
[ 7.452594] udev: starting version 141
[ 7.935966] iTCO_vendor_support: vendor-support=0
[ 8.181130] nvidia: module license 'NVIDIA' taints kernel.
[ 8.194691] Initializing USB Mass Storage driver...
[ 8.195129] scsi6 : SCSI emulation for USB Mass Storage devices
[ 8.195250] usb-storage: device found at 3
[ 8.195251] usb-storage: waiting for device to settle before scanning
[ 8.195271] scsi7 : SCSI emulation for USB Mass Storage devices
[ 8.195369] usbcore: registered new interface driver usb-storage
[ 8.195371] USB Mass Storage support registered.
[ 8.195780] usb-storage: device found at 5
[ 8.195781] usb-storage: waiting for device to settle before scanning
[ 8.233660] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 8.252044] usbcore: registered new interface driver hiddev
[ 8.268367] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 8.268507] iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0x0460)
[ 8.268561] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 8.269550] input: Genius 4D Scroll Mouse as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.0/input/input5
[ 8.284865] parport_pc 00:09: reported by Plug and Play ACPI
[ 8.284903] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 8.432247] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8.432252] nvidia 0000:01:00.0: setting latency timer to 64
[ 8.432677] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 180.44 Tue Mar 24 05:46:32 PST 2009
[ 8.449388] ppdev: user-space parallel port driver
[ 8.475658] dvb-usb: found a 'AverMedia AVerTV Volar Black HD (A850)' in warm state.
[ 8.475710] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 8.476057] DVB: registering new adapter (AverMedia AVerTV Volar Black HD (A850))
[ 8.492084] generic-usb 0003:0458:0056.0001: input,hidraw0: USB HID v1.10 Mouse [Genius 4D Scroll Mouse] on usb-0000:00:1a.1-1/input0
[ 8.492099] usbcore: registered new interface driver usbhid
[ 8.492111] usbhid: v2.6:USB HID core driver
[ 8.592250] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 8.592292] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 8.766653] af9013: firmware version:4.65.0
[ 8.769653] DVB: registering adapter 0 frontend 0 (Afatech AF9013 DVB-T)...
[ 8.792038] MXL5005S: Attached at address 0xc6
[ 8.792041] dvb-usb: AverMedia AVerTV Volar Black HD (A850) successfully initialized and connected.
[ 8.797673] usbcore: registered new interface driver dvb_usb_af9015
[ 8.865103] lp0: using parport0 (interrupt-driven).
[ 8.927463] Adding 9936160k swap on /dev/sda5. Priority:-1 extents:1 across:9936160k
[ 9.448441] EXT3 FS on sda1, internal journal
[ 10.371993] type=1505 audit(1255644017.820:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2049
[ 10.394432] type=1505 audit(1255644017.844:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2053
[ 10.394477] type=1505 audit(1255644017.844:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2053
[ 10.394500] type=1505 audit(1255644017.844:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2053
[ 10.394523] type=1505 audit(1255644017.844:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2053
[ 10.456212] type=1505 audit(1255644017.908:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2058
[ 10.456303] type=1505 audit(1255644017.908:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2058
[ 10.470504] type=1505 audit(1255644017.920:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2062
[ 13.192097] usb-storage: device scan complete
[ 13.192116] usb-storage: device scan complete
[ 13.192458] scsi 6:0:0:0: Direct-Access ChipsBnk SD/MMCReader 4081 PQ: 0 ANSI: 2
[ 13.234210] scsi 7:0:0:0: Direct-Access Hitachi HDT721075SLA380 PQ: 0 ANSI: 2 CCS
[ 13.235191] sd 7:0:0:0: [sdb] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
[ 13.235937] sd 7:0:0:0: [sdb] Write Protect is off
[ 13.235939] sd 7:0:0:0: [sdb] Mode Sense: 34 00 00 00
[ 13.235940] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 13.236592] sd 7:0:0:0: [sdb] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
[ 13.237318] sd 7:0:0:0: [sdb] Write Protect is off
[ 13.237320] sd 7:0:0:0: [sdb] Mode Sense: 34 00 00 00
[ 13.237322] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 13.237325] sdb: sdb1
[ 13.251031] sd 7:0:0:0: [sdb] Attached SCSI disk
[ 13.251084] sd 7:0:0:0: Attached scsi generic sg2 type 0
[ 13.253541] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[ 13.253570] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 13.709566] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 13.709568] Bluetooth: BNEP filters: protocol multicast
[ 13.715048] Bridge firewalling registered
[ 18.549455] r8169: eth0: link up
[ 18.549458] r8169: eth0: link up
[ 28.740006] eth0: no IPv6 routers present
[ 29.962268] UDF-fs: No VRS found
[ 29.976923] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 29.978227] ISOFS: changing to secondary root
kuchiptachi@kuchiptachi-desktop:~$
|
eishailiga
Anmeldungsdatum: 31. Oktober 2006
Beiträge: 5401
Wohnort: Sauerland
|
Nimm mal diese Firmware und starte den Rechner dann neu, probiere dann Kaffeine aus...
wget http://www.otit.fi/~crope/v4l-dvb/af9015/af9015_firmware_cutter/firmware_files/4.95.0/dvb-usb-af9015.fw sudo cp dvb-usb-af9015.fw /lib/firmware/
|
Kuchipatchi
(Themenstarter)
Anmeldungsdatum: 13. Oktober 2009
Beiträge: 31
Wohnort: Koblenz
|
Leider wieder das gleiche ☹ kuchiptachi@kuchiptachi-desktop:~$ kaffein -verbose
bash: kaffein: command not found
kuchiptachi@kuchiptachi-desktop:~$ kaffeine -verbose
kbuildsycoca running...
/dev/dvb/adapter0/frontend0 : opened ( Afatech AF9013 DVB-T )
0 EPG plugins loaded for device 0:0.
Loaded epg data : 1402 events (20 msecs)
kuchiptachi@kuchiptachi-desktop:~$ Tuning to: N24 / autocount: 0
DvbCam::probe(): /dev/dvb/adapter0/ca0: : No such file or directory
Using DVB device 0:0 "Afatech AF9013 DVB-T"
tuning DVB-T to 730000000 Hz
inv:2 bw:0 fecH:9 fecL:9 mod:6 tm:2 gi:4 hier:4
..................................................
Not able to lock to the signal on the given frequency
Frontend closed
Tuning delay: 7086 ms
Tuning to: RTL2 / autocount: 0
Using DVB device 0:0 "Afatech AF9013 DVB-T"
tuning DVB-T to 538000000 Hz
inv:2 bw:0 fecH:9 fecL:9 mod:6 tm:2 gi:4 hier:4
..................................................
Not able to lock to the signal on the given frequency
Frontend closed
Tuning delay: 7042 ms
Tuning to: VIVA / autocount: 0
Using DVB device 0:0 "Afatech AF9013 DVB-T"
tuning DVB-T to 594000000 Hz
inv:2 bw:0 fecH:9 fecL:9 mod:6 tm:2 gi:4 hier:4
..................................................
Not able to lock to the signal on the given frequency
Frontend closed
Tuning delay: 9527 ms
|
eishailiga
Anmeldungsdatum: 31. Oktober 2006
Beiträge: 5401
Wohnort: Sauerland
|
Poste doch nochmal die Ausgabe von dmesg
|
Kuchipatchi
(Themenstarter)
Anmeldungsdatum: 13. Oktober 2009
Beiträge: 31
Wohnort: Koblenz
|
[ 0.372526] pci 0000:03:00.0: reg 18 io port: [0xc200-0xc207]
[ 0.372533] pci 0000:03:00.0: reg 1c io port: [0xc300-0xc303]
[ 0.372541] pci 0000:03:00.0: reg 20 io port: [0xc400-0xc40f]
[ 0.372597] pci 0000:00:1c.3: bridge io port: [0xc000-0xcfff]
[ 0.372600] pci 0000:00:1c.3: bridge 32bit mmio: [0xe8000000-0xe8ffffff]
[ 0.372649] pci 0000:04:00.0: reg 10 io port: [0xd000-0xd0ff]
[ 0.372668] pci 0000:04:00.0: reg 18 64bit mmio: [0xea000000-0xea000fff]
[ 0.372686] pci 0000:04:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 0.372696] pci 0000:04:00.0: supports D1 D2
[ 0.372697] pci 0000:04:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.372701] pci 0000:04:00.0: PME# disabled
[ 0.372736] pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff]
[ 0.372739] pci 0000:00:1c.4: bridge 32bit mmio: [0xe9000000-0xeaffffff]
[ 0.372778] pci 0000:00:1e.0: transparent bridge
[ 0.372780] pci 0000:00:1e.0: bridge io port: [0xa000-0xafff]
[ 0.372799] bus 00 -> node 0
[ 0.372803] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.372955] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 0.373021] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
[ 0.373088] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[ 0.373153] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.384335] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.384412] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.384490] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[ 0.384565] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.384641] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.384717] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.384793] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[ 0.384868] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.385004] ACPI: WMI: Mapper loaded
[ 0.385049] SCSI subsystem initialized
[ 0.385049] libata version 3.00 loaded.
[ 0.385049] usbcore: registered new interface driver usbfs
[ 0.385049] usbcore: registered new interface driver hub
[ 0.385049] usbcore: registered new device driver usb
[ 0.385049] PCI: Using ACPI for IRQ routing
[ 0.396008] Bluetooth: Core ver 2.13
[ 0.396019] NET: Registered protocol family 31
[ 0.396019] Bluetooth: HCI device and connection manager initialized
[ 0.396019] Bluetooth: HCI socket layer initialized
[ 0.396020] NET: Registered protocol family 8
[ 0.396021] NET: Registered protocol family 20
[ 0.396031] NetLabel: Initializing
[ 0.396032] NetLabel: domain hash size = 128
[ 0.396033] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.396044] NetLabel: unlabeled traffic allowed by default
[ 0.396069] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.396073] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 0.400058] AppArmor: AppArmor Filesystem Enabled
[ 0.412010] pnp: PnP ACPI init
[ 0.412017] ACPI: bus type pnp registered
[ 0.414043] pnp: PnP ACPI: found 15 devices
[ 0.414044] ACPI: ACPI bus type pnp unregistered
[ 0.414049] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 0.414051] system 00:01: ioport range 0x290-0x29f has been reserved
[ 0.414052] system 00:01: ioport range 0x800-0x87f has been reserved
[ 0.414054] system 00:01: ioport range 0x290-0x294 has been reserved
[ 0.414055] system 00:01: ioport range 0x880-0x88f has been reserved
[ 0.414060] system 00:0b: ioport range 0x400-0x4bf could not be reserved
[ 0.414063] system 00:0c: iomem range 0xe0000000-0xe3ffffff has been reserved
[ 0.414066] system 00:0d: iomem range 0xce200-0xcffff has been reserved
[ 0.414068] system 00:0d: iomem range 0xf0000-0xf7fff could not be reserved
[ 0.414069] system 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.414071] system 00:0d: iomem range 0xfc000-0xfffff could not be reserved
[ 0.414072] system 00:0d: iomem range 0xbfee0000-0xbfefffff could not be reserved
[ 0.414073] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 0.414075] system 00:0d: iomem range 0x100000-0xbfedffff could not be reserved
[ 0.414076] system 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.414078] system 00:0d: iomem range 0xfed10000-0xfed1dfff has been reserved
[ 0.414080] system 00:0d: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 0.414082] system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.414083] system 00:0d: iomem range 0xffb00000-0xffb7ffff has been reserved
[ 0.414084] system 00:0d: iomem range 0xfff00000-0xffffffff has been reserved
[ 0.414086] system 00:0d: iomem range 0xe0000-0xeffff has been reserved
[ 0.418688] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.418689] pci 0000:00:01.0: IO window: 0xb000-0xbfff
[ 0.418692] pci 0000:00:01.0: MEM window: 0xe4000000-0xe7ffffff
[ 0.418694] pci 0000:00:01.0: PREFETCH window: 0x000000c0000000-0x000000dfffffff
[ 0.418696] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.418698] pci 0000:00:1c.0: IO window: 0x9000-0x9fff
[ 0.418701] pci 0000:00:1c.0: MEM window: disabled
[ 0.418703] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.418707] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:03
[ 0.418709] pci 0000:00:1c.3: IO window: 0xc000-0xcfff
[ 0.418712] pci 0000:00:1c.3: MEM window: 0xe8000000-0xe8ffffff
[ 0.418714] pci 0000:00:1c.3: PREFETCH window: disabled
[ 0.418718] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:04
[ 0.418720] pci 0000:00:1c.4: IO window: 0xd000-0xdfff
[ 0.418723] pci 0000:00:1c.4: MEM window: 0xe9000000-0xeaffffff
[ 0.418725] pci 0000:00:1c.4: PREFETCH window: 0x000000eb100000-0x000000eb1fffff
[ 0.418729] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[ 0.418731] pci 0000:00:1e.0: IO window: 0xa000-0xafff
[ 0.418734] pci 0000:00:1e.0: MEM window: disabled
[ 0.418736] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.418744] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.418746] pci 0000:00:01.0: setting latency timer to 64
[ 0.418750] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.418753] pci 0000:00:1c.0: setting latency timer to 64
[ 0.418758] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.418760] pci 0000:00:1c.3: setting latency timer to 64
[ 0.418765] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.418767] pci 0000:00:1c.4: setting latency timer to 64
[ 0.418771] pci 0000:00:1e.0: setting latency timer to 64
[ 0.418773] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.418775] bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff]
[ 0.418776] bus: 01 index 0 io port: [0xb000-0xbfff]
[ 0.418777] bus: 01 index 1 mmio: [0xe4000000-0xe7ffffff]
[ 0.418778] bus: 01 index 2 mmio: [0xc0000000-0xdfffffff]
[ 0.418779] bus: 01 index 3 mmio: [0x0-0x0]
[ 0.418780] bus: 02 index 0 io port: [0x9000-0x9fff]
[ 0.418781] bus: 02 index 1 mmio: [0x0-0x0]
[ 0.418782] bus: 02 index 2 mmio: [0x0-0x0]
[ 0.418783] bus: 02 index 3 mmio: [0x0-0x0]
[ 0.418784] bus: 03 index 0 io port: [0xc000-0xcfff]
[ 0.418785] bus: 03 index 1 mmio: [0xe8000000-0xe8ffffff]
[ 0.418786] bus: 03 index 2 mmio: [0x0-0x0]
[ 0.418786] bus: 03 index 3 mmio: [0x0-0x0]
[ 0.418788] bus: 04 index 0 io port: [0xd000-0xdfff]
[ 0.418789] bus: 04 index 1 mmio: [0xe9000000-0xeaffffff]
[ 0.418790] bus: 04 index 2 mmio: [0xeb100000-0xeb1fffff]
[ 0.418791] bus: 04 index 3 mmio: [0x0-0x0]
[ 0.418792] bus: 05 index 0 io port: [0xa000-0xafff]
[ 0.418793] bus: 05 index 1 mmio: [0x0-0x0]
[ 0.418794] bus: 05 index 2 mmio: [0x0-0x0]
[ 0.418795] bus: 05 index 3 io port: [0x00-0xffff]
[ 0.418796] bus: 05 index 4 mmio: [0x000000-0xffffffffffffffff]
[ 0.418801] NET: Registered protocol family 2
[ 0.452056] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.452284] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.453123] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.453373] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.453375] TCP reno registered
[ 0.464091] NET: Registered protocol family 1
[ 0.464183] checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
[ 0.504019] Switched to high resolution mode on CPU 0
[ 0.682947] it is
[ 0.912419] Freeing initrd memory: 7761k freed
[ 0.914293] audit: initializing netlink socket (disabled)
[ 0.914313] type=2000 audit(1255645331.912:1): initialized
[ 0.919855] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.920622] VFS: Disk quotas dquot_6.5.1
[ 0.920654] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.921000] fuse init (API version 7.10)
[ 0.921045] msgmni has been set to 7788
[ 0.921150] alg: No test for stdrng (krng)
[ 0.921156] io scheduler noop registered
[ 0.921157] io scheduler anticipatory registered
[ 0.921158] io scheduler deadline registered
[ 0.921184] io scheduler cfq registered (default)
[ 0.921305] pci 0000:01:00.0: Boot video device
[ 0.923008] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 0.923027] pcieport-driver 0000:00:01.0: found MSI capability
[ 0.923041] pcieport-driver 0000:00:01.0: irq 2303 for MSI/MSI-X
[ 0.923047] pci_express 0000:00:01.0:pcie00: allocate port service
[ 0.923054] pci_express 0000:00:01.0:pcie03: allocate port service
[ 0.923082] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.923105] pcieport-driver 0000:00:1c.0: found MSI capability
[ 0.923121] pcieport-driver 0000:00:1c.0: irq 2302 for MSI/MSI-X
[ 0.923129] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 0.923136] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 0.923145] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 0.923181] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[ 0.923204] pcieport-driver 0000:00:1c.3: found MSI capability
[ 0.923220] pcieport-driver 0000:00:1c.3: irq 2301 for MSI/MSI-X
[ 0.923228] pci_express 0000:00:1c.3:pcie00: allocate port service
[ 0.923235] pci_express 0000:00:1c.3:pcie02: allocate port service
[ 0.923242] pci_express 0000:00:1c.3:pcie03: allocate port service
[ 0.923279] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 0.923301] pcieport-driver 0000:00:1c.4: found MSI capability
[ 0.923317] pcieport-driver 0000:00:1c.4: irq 2300 for MSI/MSI-X
[ 0.923325] pci_express 0000:00:1c.4:pcie00: allocate port service
[ 0.923334] pci_express 0000:00:1c.4:pcie02: allocate port service
[ 0.923341] pci_express 0000:00:1c.4:pcie03: allocate port service
[ 0.923385] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.923579] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.923672] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.923673] ACPI: Power Button (FF) [PWRF]
[ 0.923700] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.923701] ACPI: Power Button (CM) [PWRB]
[ 0.923889] processor ACPI_CPU:00: registered as cooling_device0
[ 0.923892] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 0.924010] ACPI: SSDT BFEE8300, 0087 (r1 PmRef Cpu1Ist 3000 INTL 20040311)
[ 0.924128] processor ACPI_CPU:01: registered as cooling_device1
[ 0.924131] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 0.952652] Linux agpgart interface v0.103
[ 0.952659] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 0.952735] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.952954] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.953418] brd: module loaded
[ 0.953607] loop: module loaded
[ 0.953644] Fixed MDIO Bus: probed
[ 0.953647] PPP generic driver version 2.4.2
[ 0.953683] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.953699] Driver 'sd' needs updating - please use bus_type methods
[ 0.953704] Driver 'sr' needs updating - please use bus_type methods
[ 0.953748] ata_piix 0000:00:1f.2: version 2.12
[ 0.953756] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.953758] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[ 0.953786] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.953831] scsi0 : ata_piix
[ 0.953872] scsi1 : ata_piix
[ 0.954292] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 0.954294] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 1.428047] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.444173] ata1.00: HPA unlocked: 488395055 -> 488397168, native 488397168
[ 1.444176] ata1.00: ATA-7: SAMSUNG HD250HJ, FH100-06, max UDMA7
[ 1.444177] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.452274] ata1.00: configured for UDMA/133
[ 1.928049] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.936175] ata2.00: ATAPI: HL-DT-ST DVDRAM GH20NS10, EL00, max UDMA/100
[ 1.952183] ata2.00: configured for UDMA/100
[ 1.957548] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD250HJ FH10 PQ: 0 ANSI: 5
[ 1.957610] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 1.957621] sd 0:0:0:0: [sda] Write Protect is off
[ 1.957622] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.957637] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.957678] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 1.957687] sd 0:0:0:0: [sda] Write Protect is off
[ 1.957688] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.957703] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.957705] sda: sda1 sda2 < sda5 >
[ 1.985796] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.985820] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.988843] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GH20NS10 EL00 PQ: 0 ANSI: 5
[ 1.992657] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.992660] Uniform CD-ROM driver Revision: 3.20
[ 1.992726] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.992758] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.992775] ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.992778] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 1.992807] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 1.992853] scsi2 : ata_piix
[ 1.992886] scsi3 : ata_piix
[ 1.993235] ata3: SATA max UDMA/133 cmd 0xe700 ctl 0xe800 bmdma 0xeb00 irq 19
[ 1.993237] ata4: SATA max UDMA/133 cmd 0xe900 ctl 0xea00 bmdma 0xeb08 irq 19
[ 2.322516] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.650515] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.650708] pata_jmicron 0000:03:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 2.650727] pata_jmicron 0000:03:00.0: setting latency timer to 64
[ 2.650761] scsi4 : pata_jmicron
[ 2.650794] scsi5 : pata_jmicron
[ 2.651243] ata5: PATA max UDMA/100 cmd 0xc000 ctl 0xc100 bmdma 0xc400 irq 19
[ 2.651245] ata6: PATA max UDMA/100 cmd 0xc200 ctl 0xc300 bmdma 0xc408 irq 19
[ 2.960251] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.960262] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.960271] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 2.960273] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.960309] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 2.964194] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 2.964202] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xeb004000
[ 2.980008] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 2.980062] usb usb1: configuration #1 chosen from 1 choice
[ 2.980084] hub 1-0:1.0: USB hub found
[ 2.980090] hub 1-0:1.0: 6 ports detected
[ 2.980165] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.980171] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2.980173] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.980195] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 2.984093] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 2.984101] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xeb005000
[ 2.996007] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.996052] usb usb2: configuration #1 chosen from 1 choice
[ 2.996072] hub 2-0:1.0: USB hub found
[ 2.996077] hub 2-0:1.0: 6 ports detected
[ 2.996146] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.996154] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.996165] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.996169] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.996170] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.996194] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 2.996218] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000e100
[ 2.996260] usb usb3: configuration #1 chosen from 1 choice
[ 2.996276] hub 3-0:1.0: USB hub found
[ 2.996279] hub 3-0:1.0: 2 ports detected
[ 2.996328] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 2.996332] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 2.996334] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.996357] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 2.996379] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000e200
[ 2.996425] usb usb4: configuration #1 chosen from 1 choice
[ 2.996438] hub 4-0:1.0: USB hub found
[ 2.996441] hub 4-0:1.0: 2 ports detected
[ 2.996488] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.996492] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 2.996493] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 2.996521] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[ 2.996538] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000e000
[ 2.996581] usb usb5: configuration #1 chosen from 1 choice
[ 2.996594] hub 5-0:1.0: USB hub found
[ 2.996598] hub 5-0:1.0: 2 ports detected
[ 2.996646] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.996649] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.996651] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.996681] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 2.996698] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e300
[ 2.996739] usb usb6: configuration #1 chosen from 1 choice
[ 2.996756] hub 6-0:1.0: USB hub found
[ 2.996759] hub 6-0:1.0: 2 ports detected
[ 2.996805] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.996809] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.996811] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.996837] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 2.996854] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e400
[ 2.996896] usb usb7: configuration #1 chosen from 1 choice
[ 2.996911] hub 7-0:1.0: USB hub found
[ 2.996915] hub 7-0:1.0: 2 ports detected
[ 2.996963] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.996967] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.996969] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.996992] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 2.997010] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e500
[ 2.997053] usb usb8: configuration #1 chosen from 1 choice
[ 2.997066] hub 8-0:1.0: USB hub found
[ 2.997069] hub 8-0:1.0: 2 ports detected
[ 2.997143] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 2.997144] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 2.997189] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.008530] mice: PS/2 mouse device common for all mice
[ 3.044549] rtc_cmos 00:04: RTC can wake from S4
[ 3.044575] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 3.044596] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 3.044639] device-mapper: uevent: version 1.0.3
[ 3.044685] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 3.044728] device-mapper: multipath: version 1.0.5 loaded
[ 3.044730] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 3.044782] cpuidle: using governor ladder
[ 3.044783] cpuidle: using governor menu
[ 3.045021] TCP cubic registered
[ 3.045060] NET: Registered protocol family 10
[ 3.045296] lo: Disabled Privacy Extensions
[ 3.045462] NET: Registered protocol family 17
[ 3.045472] Bluetooth: L2CAP ver 2.11
[ 3.045473] Bluetooth: L2CAP socket layer initialized
[ 3.045475] Bluetooth: SCO (Voice Link) ver 0.6
[ 3.045475] Bluetooth: SCO socket layer initialized
[ 3.045489] Bluetooth: RFCOMM socket layer initialized
[ 3.045493] Bluetooth: RFCOMM TTY layer initialized
[ 3.045494] Bluetooth: RFCOMM ver 1.10
[ 3.047505] registered taskstats version 1
[ 3.047600] Magic number: 13:309:401
[ 3.047668] rtc_cmos 00:04: setting system clock to 2009-10-15 22:22:14 UTC (1255645334)
[ 3.047669] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 3.047670] EDD information not available.
[ 3.047695] Freeing unused kernel memory: 536k freed
[ 3.047789] Write protecting the kernel read-only data: 6688k
[ 3.070894] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 3.164821] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 3.164836] r8169 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.164852] r8169 0000:04:00.0: setting latency timer to 64
[ 3.164934] r8169 0000:04:00.0: irq 2299 for MSI/MSI-X
[ 3.165304] eth0: RTL8168b/8111b at 0xffffc2000005e000, 00:1d:7d:e9:3b:ef, XID 38000000 IRQ 2299
[ 3.228760] Floppy drive(s): fd0 is 1.44M
[ 3.247703] FDC 0 is a post-1991 82077
[ 3.292599] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 3.378763] PM: Starting manual resume from disk
[ 3.378765] PM: Resume from partition 8:5
[ 3.378766] PM: Checking hibernation image.
[ 3.378888] PM: Resume from disk failed.
[ 3.417082] kjournald starting. Commit interval 5 seconds
[ 3.417090] EXT3-fs: mounted filesystem with ordered data mode.
[ 3.428752] usb 1-1: configuration #1 chosen from 1 choice
[ 3.540008] usb 1-2: new high speed USB device using ehci_hcd and address 3
[ 3.672906] usb 1-2: configuration #1 chosen from 1 choice
[ 3.840011] usb 1-4: new high speed USB device using ehci_hcd and address 5
[ 3.972937] usb 1-4: configuration #1 chosen from 1 choice
[ 4.212511] usb 4-1: new low speed USB device using uhci_hcd and address 2
[ 4.386643] usb 4-1: configuration #1 chosen from 1 choice
[ 7.428293] udev: starting version 141
[ 7.949326] nvidia: module license 'NVIDIA' taints kernel.
[ 8.200292] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8.200298] nvidia 0000:01:00.0: setting latency timer to 64
[ 8.200753] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 180.44 Tue Mar 24 05:46:32 PST 2009
[ 8.350610] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 8.364499] usbcore: registered new interface driver hiddev
[ 8.377999] Initializing USB Mass Storage driver...
[ 8.378070] scsi6 : SCSI emulation for USB Mass Storage devices
[ 8.378158] usb-storage: device found at 3
[ 8.378159] usb-storage: waiting for device to settle before scanning
[ 8.378178] scsi7 : SCSI emulation for USB Mass Storage devices
[ 8.378442] usbcore: registered new interface driver usb-storage
[ 8.378455] USB Mass Storage support registered.
[ 8.378458] usb-storage: device found at 5
[ 8.378458] usb-storage: waiting for device to settle before scanning
[ 8.382389] input: Genius 4D Scroll Mouse as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.0/input/input5
[ 8.384624] iTCO_vendor_support: vendor-support=0
[ 8.385698] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 8.385789] iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0x0460)
[ 8.385838] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 8.412594] generic-usb 0003:0458:0056.0001: input,hidraw0: USB HID v1.10 Mouse [Genius 4D Scroll Mouse] on usb-0000:00:1a.1-1/input0
[ 8.412609] usbcore: registered new interface driver usbhid
[ 8.412627] usbhid: v2.6:USB HID core driver
[ 8.435032] parport_pc 00:09: reported by Plug and Play ACPI
[ 8.435072] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 8.519340] dvb-usb: found a 'AverMedia AVerTV Volar Black HD (A850)' in warm state.
[ 8.519373] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 8.519744] DVB: registering new adapter (AverMedia AVerTV Volar Black HD (A850))
[ 8.582885] ppdev: user-space parallel port driver
[ 8.742415] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 8.742457] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 8.768001] af9013: firmware version:4.65.0
[ 8.771001] DVB: registering adapter 0 frontend 0 (Afatech AF9013 DVB-T)...
[ 8.801182] MXL5005S: Attached at address 0xc6
[ 8.801185] dvb-usb: AverMedia AVerTV Volar Black HD (A850) successfully initialized and connected.
[ 8.806767] usbcore: registered new interface driver dvb_usb_af9015
[ 8.906989] lp0: using parport0 (interrupt-driven).
[ 8.969778] Adding 9936160k swap on /dev/sda5. Priority:-1 extents:1 across:9936160k
[ 9.490928] EXT3 FS on sda1, internal journal
[ 10.397980] type=1505 audit(1255645341.848:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2045
[ 10.420532] type=1505 audit(1255645341.872:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2049
[ 10.420578] type=1505 audit(1255645341.872:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2049
[ 10.420601] type=1505 audit(1255645341.872:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2049
[ 10.420623] type=1505 audit(1255645341.872:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2049
[ 10.482415] type=1505 audit(1255645341.932:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2054
[ 10.482506] type=1505 audit(1255645341.932:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2054
[ 10.496745] type=1505 audit(1255645341.948:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2058
[ 13.376126] usb-storage: device scan complete
[ 13.376151] usb-storage: device scan complete
[ 13.376483] scsi 6:0:0:0: Direct-Access ChipsBnk SD/MMCReader 4081 PQ: 0 ANSI: 2
[ 13.378409] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 13.378452] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 13.418126] scsi 7:0:0:0: Direct-Access Hitachi HDT721075SLA380 PQ: 0 ANSI: 2 CCS
[ 13.419097] sd 7:0:0:0: [sdc] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
[ 13.419866] sd 7:0:0:0: [sdc] Write Protect is off
[ 13.419867] sd 7:0:0:0: [sdc] Mode Sense: 34 00 00 00
[ 13.419868] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 13.420475] sd 7:0:0:0: [sdc] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
[ 13.421599] sd 7:0:0:0: [sdc] Write Protect is off
[ 13.421602] sd 7:0:0:0: [sdc] Mode Sense: 34 00 00 00
[ 13.421603] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 13.421606] sdc: sdc1
[ 13.436187] sd 7:0:0:0: [sdc] Attached SCSI disk
[ 13.436241] sd 7:0:0:0: Attached scsi generic sg3 type 0
[ 13.744442] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 13.744443] Bluetooth: BNEP filters: protocol multicast
[ 13.749837] Bridge firewalling registered
[ 19.547669] r8169: eth0: link up
[ 19.547672] r8169: eth0: link up
[ 29.756006] eth0: no IPv6 routers present
[ 30.504064] UDF-fs: No VRS found
[ 30.518729] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 30.520014] ISOFS: changing to secondary root
[ 349.332022] usb 5-1: new full speed USB device using uhci_hcd and address 2
[ 349.452031] usb 5-1: device descriptor read/64, error -71
[ 349.624075] hub 5-0:1.0: unable to enumerate USB device on port 1
[ 353.212514] usb 5-1: new full speed USB device using uhci_hcd and address 3
[ 353.389059] usb 5-1: configuration #1 chosen from 1 choice
[ 353.427321] cdc_acm 5-1:1.0: ttyACM0: USB ACM device
[ 353.429871] usbcore: registered new interface driver cdc_acm
[ 353.429874] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
kuchiptachi@kuchiptachi-desktop:~$
|
eishailiga
Anmeldungsdatum: 31. Oktober 2006
Beiträge: 5401
Wohnort: Sauerland
|
Laut dmesg, wird immer noch die Firmware v4.65 geladen, obwohl du v4.95 installiert hast... Ziehe doch den Stick ab und stecke ihn dann wieder an...und probiere erneut...
|
Kuchipatchi
(Themenstarter)
Anmeldungsdatum: 13. Oktober 2009
Beiträge: 31
Wohnort: Koblenz
|
Schau an es geht !
Woher wusstest du das es dieser Treiber ist und wie man Ihn lädt ?? Gruß Leon
|
eishailiga
Anmeldungsdatum: 31. Oktober 2006
Beiträge: 5401
Wohnort: Sauerland
|
Ich habe schon häufiger für diesen Stick Installationsanleitungen gepostet und habe aus deinen geposteten Links ersehen, daß du den Treiber richtig installiert hast aber nicht die aktuelle Firmware für den Stick, die ältere Firmware erkennt den Stick als af9013 obwohl es sich um einen af9015 Chipsatz handelt...die ältere Firmware ist für die Vorgänger deines Sticks... ☺ Falls das Thema hier für dich gelöst ist, dann kannst du ihn ja als gelöst markieren... 😉
|
Kuchipatchi
(Themenstarter)
Anmeldungsdatum: 13. Oktober 2009
Beiträge: 31
Wohnort: Koblenz
|
Jup markiere ich jetzt als gelöst. Wird es mit der neuen UbuntuVersion auch zu solchen Problemen kommen ?
|