Hallo,
einen DSL-Anschluss nach der Wiki versuche ich mit pppoeconf zu installieren. Das klappt auch bis zum nächsten Neustart.
Über lsmod lasse ich mir die Module pppoe und pppox anzeigen. pppoe läuft nicht, die 0 steht da.
Ich beende ich erstmal die Prozesse networking und ppp.
/etc/init.d/networking stop
/etc/init.d/ppp stop
Dann entlade ich die Module mit rmmod.
Starte networking wieder und es läuft.
Jetzt schaue ich mir gerade die interfaces an und bin verwirrt:
\––\––\––\––\––\––\––\––\––\––\––\––\––\––\––\––\––\–––
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
auto dsl-provider
iface dsl-provider inet ppp
provider dsl-provider
# added by pppoeconf
auto eth0
iface eth0 inet manual
pre-up /sbin/ifconfig eth1 up # line maintained by pppoeconf
# added by pppoeconf
auto eth1
iface eth1 inet manual
\––\––\––\––\––\––\––\––\––\––\––\––\––\–––
ifconfig liefert mir:
\––\––\––\––\––\––\––\––\––\––\–––-
xxx@computer:/etc/network$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:0C:F1:01:8B:A1
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0xc000 Memory:e0200000-e0200fff
eth1 Link encap:Ethernet HWaddr 00:40:CA:C5:43:EF
inet6 addr: fe80::240:caff:fec5:43ef/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1778 errors:0 dropped:0 overruns:0 frame:0
TX packets:1706 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1325739 (1.2 MiB) TX bytes:344902 (336.8 KiB)
Interrupt:10 Base address:0x2800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
ppp0 Link encap:Point-to-Point Protocol
inet addr:85.182.3.209 P-t-P:213.191.89.24 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:1686 errors:0 dropped:0 overruns:0 frame:0
TX packets:1612 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
\––\––\––\––\––\––\––\––\––\––\––\––\––\–––-
Welche Karte nutze ich denn nun? Wahrscheinlich muss ich dann an der interfaces was machen.
Aber vor allem, wie löse ich die Sache mit den Modulen?
Hoffentlich könnt Ihr mir weiterhelfen,
viele Grüße,
Christoph