smartctl -a /dev/sda
smartctl 6.4 2015-06-04 r4109 [x86_64-linux-4.2.6-64] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABF...
Device Model: TOSHIBA MQ01ABF050
Serial Number: 932AC0JCT
LU WWN Device Id: 5 000039 50378076b
Firmware Version: AM001K
User Capacity: 500.107.862.016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Feb 25 17:40:09 2016 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 126) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1335
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 2676
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 1927
10 Spin_Retry_Count 0x0033 153 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2414
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 195
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 46
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 18020
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 31 (Min/Max 11/50)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 096 096 000 Old_age Always - 1848
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 263
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4 occurred at disk power-on lifetime: 1920 hours (80 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 60 98 51 99 40 Error: UNC at LBA = 0x00995198 = 10047896
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 60 98 51 99 40 00 00:41:32.181 READ FPDMA QUEUED
60 08 58 90 51 99 40 00 00:41:32.181 READ FPDMA QUEUED
60 08 50 88 51 99 40 00 00:41:32.181 READ FPDMA QUEUED
60 08 48 80 51 99 40 00 00:41:32.180 READ FPDMA QUEUED
60 08 40 78 51 99 40 00 00:41:32.180 READ FPDMA QUEUED
Error 3 occurred at disk power-on lifetime: 1920 hours (80 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 b0 98 51 99 40 Error: UNC at LBA = 0x00995198 = 10047896
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 b0 00 50 99 40 00 00:41:28.787 READ FPDMA QUEUED
60 00 a8 00 4e 99 40 00 00:41:28.785 READ FPDMA QUEUED
60 00 a0 00 4c 99 40 00 00:41:28.782 READ FPDMA QUEUED
60 00 98 00 4a 99 40 00 00:41:28.780 READ FPDMA QUEUED
60 00 90 00 48 99 40 00 00:41:28.778 READ FPDMA QUEUED
Error 2 occurred at disk power-on lifetime: 1907 hours (79 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 60 98 51 99 40 Error: UNC at LBA = 0x00995198 = 10047896
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 60 98 51 99 40 00 00:36:57.759 READ FPDMA QUEUED
60 08 58 90 51 99 40 00 00:36:57.759 READ FPDMA QUEUED
60 08 50 88 51 99 40 00 00:36:57.759 READ FPDMA QUEUED
60 08 48 80 51 99 40 00 00:36:57.758 READ FPDMA QUEUED
60 08 40 78 51 99 40 00 00:36:57.758 READ FPDMA QUEUED
Error 1 occurred at disk power-on lifetime: 1907 hours (79 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 b0 98 51 99 40 Error: UNC at LBA = 0x00995198 = 10047896
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 b0 00 50 99 40 00 00:36:54.209 READ FPDMA QUEUED
60 00 a8 00 4e 99 40 00 00:36:54.207 READ FPDMA QUEUED
60 00 a0 00 4c 99 40 00 00:36:54.205 READ FPDMA QUEUED
60 00 98 00 4a 99 40 00 00:36:54.203 READ FPDMA QUEUED
60 00 90 00 48 99 40 00 00:36:54.201 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1927 -
# 2 Short offline Completed without error 00% 1927 -
# 3 Short offline Completed without error 00% 1926 -
# 4 Short offline Interrupted (host reset) 10% 1926 -
# 5 Short offline Completed without error 00% 1926 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Hallo Ihr Lieben
Hier ist dei ausgabe von smartctl -a. Ich hoffe es hat diesmal mit dem Codeblock geklappt.
Mit freundlichen Grüßen Johannes schaffer