Hallo an alle,
leider hat auf meinen Hilferuf vom 14.10. keiner geantwortet, deshalb versuche ich es noch einmal.
Ich suche noch immer verzweifelt Hilfe, da ich die Fritz ISDN Karte nicht zum laufen bringe und keine Alternative (außer Windows habe)!
Ich bin absoluter Ubuntu Neuling mit langer Windows und Suse Erfahrung, wo man sich um das Einbinden der ISDN Karte fast nicht zu kümmern braucht! Nach einer erneuten Neuinstallation, habe ich mich bemüht, strikt der "Anleitung für Fritz Card PCI (V2.0)" von Iceman vom 1.11.2004 zu folgen. Das erste Problem tauchte dabei mit dem Paket 'isdnactivecards' auf, das nicht gefunden wurde.
Der gegenwärtige Status ist den folgenden Ausdrucken zu entnehmen:
klaus@DIEHL:~$ capiinfo capi not installed - No such device or address (6) klaus@DIEHL:~$ lspci | grep Ethernet 0000:00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a1) klaus@DIEHL:~$ lspci | grep ISDN 0000:04:0a.0 Network controller: AVM Audiovisuelles MKTG & Computer System GmbH Fritz!PCI v2.0 ISDN (rev 01) klaus@DIEHL:~$ lsusb Bus 002 Device 007: ID 0ea0:2168 Ours Technology, Inc. Transcend JetFlash 2.0 / Astone USB Drive Bus 002 Device 006: ID 0d49:5010 Maxtor Bus 002 Device 002: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 002 Device 001: ID 0000:0000 Bus 001 Device 002: ID 0425:f102 Motorola Semiconductors HK, Ltd Bus 001 Device 004: ID 046d:c30e Logitech, Inc. Bus 001 Device 003: ID 03f0:7304 Hewlett-Packard DeskJet 35xx Bus 001 Device 001: ID 0000:0000 klaus@DIEHL:~$ sudo dump_cis Password: sudo: dump_cis: command not found klaus@DIEHL:~$ cat -v "^$|^#" /etc/network/interfaces cat: ^$|^#: No such file or directory # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback iface eth0 inet static address 192.168.115.1 netmask 255.255.255.0 auto eth0 klaus@DIEHL:~$ cat -v "^$|^#" /etc/resolv.conf cat: ^$|^#: No such file or directory klaus@DIEHL:~$ cat -v "^$|^#" /etc/hosts cat: ^$|^#: No such file or directory 127.0.0.1 localhost DIEHL 127.0.1.1 DIEHL # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts klaus@DIEHL:~$ ifconfig eth0 Protokoll:Ethernet Hardware Adresse 00:13:8F:5D:32:73 inet Adresse:192.168.115.1 Bcast:192.168.115.255 Maske:255.255.255.0 inet6 Adresse: fe80::213:8fff:fe5d:3273/64 Gültigkeitsbereich:Verbindung UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7181 errors:0 dropped:0 overruns:0 frame:0 TX packets:7090 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenlänge:1000 RX bytes:443129 (432.7 KiB) TX bytes:528110 (515.7 KiB) Interrupt:217 Basisadresse:0xe000 lo Protokoll:Lokale Schleife inet Adresse:127.0.0.1 Maske:255.0.0.0 inet6 Adresse: ::1/128 Gültigkeitsbereich:Maschine UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:182 errors:0 dropped:0 overruns:0 frame:0 TX packets:182 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenlänge:0 RX bytes:14586 (14.2 KiB) TX bytes:14586 (14.2 KiB) klaus@DIEHL:~$ route Kernel IP Routentabelle Ziel Router Genmask Flags Metric Ref Use Iface 192.168.115.0 * 255.255.255.0 U 0 0 0 eth0 klaus@DIEHL:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. sit0 no wireless extensions. klaus@DIEHL:~$ ping -c 4 www.ubuntuusers.de ping: unknown host www.ubuntuusers.de klaus@DIEHL:~$ ping -c 80.82.17.133 Usage: ping [-LRUbdfnqrvVaA] [-c count] [-i interval] [-w deadline] [-p pattern] [-s packetsize] [-t ttl] [-I interface or address] [-M mtu discovery hint] [-S sndbuf] [ -T timestamp option ] [ -Q tos ] [hop1 ...] destination klaus@DIEHL:~$ www.ubuntuusers.de
Ich weiß jetzt nicht mehr weiter, möchte aber gerne nur noch Ubuntu nutzen und Windows und Suse in die Wüste schicken!
In Hoffnung auf baldige Hilfe, sage ich schon mal Danke.
Gruß Klaus