Wie soll es nun weitergehen?
Ich kann dir hierbei keine weiteren Tipps geben.Du könntest den plustek Treiber noch selber bauen – aber ich glaube der Scanner ist hin 😇
Gruß Stephan
Anmeldungsdatum: Beiträge: 19610 Wohnort: Schleswig-Holstein |
Ich kann dir hierbei keine weiteren Tipps geben.Du könntest den plustek Treiber noch selber bauen – aber ich glaube der Scanner ist hin 😇 Gruß Stephan |
Supporter, Wikiteam
(Themenstarter)
Anmeldungsdatum: Beiträge: 17660 Wohnort: in deinem Browser, hier auf dem Bildschirm |
Warum passiert das dann aber nicht wenn man Simple Scan beendet und wieder startet? |
Anmeldungsdatum: Beiträge: 19610 Wohnort: Schleswig-Holstein |
KP,weil der CCD wieder neu gestartet wird ❓ Ich weiß es echt nicht. |
Anmeldungsdatum: Beiträge: 29240 Wohnort: Germany |
Hast du die Kiste schon unter (altem in VM?) Win getestet? |
Supporter, Wikiteam
(Themenstarter)
Anmeldungsdatum: Beiträge: 17660 Wohnort: in deinem Browser, hier auf dem Bildschirm |
Unter Win 10 x64 finde ich keinen passenden Treiber. Ich kann Win 10 32-Bit in ner VM mit Virtualbox probieren. Ich kann auch Win 7 x64 nehmen, ist noch als Zweitsystem auf meinem Laptop. |
Anmeldungsdatum: Beiträge: 19610 Wohnort: Schleswig-Holstein |
Du brauchst dazu Win7 32 Bit! Für 64 Bit gibt es auch keine mehr. |
Supporter, Wikiteam
(Themenstarter)
Anmeldungsdatum: Beiträge: 17660 Wohnort: in deinem Browser, hier auf dem Bildschirm |
Also versuche ich es mit Win 7 32-Bit in einer VM. Melde mich dann, sobald die läuft. |
Supporter, Wikiteam
(Themenstarter)
Anmeldungsdatum: Beiträge: 17660 Wohnort: in deinem Browser, hier auf dem Bildschirm |
Win 7 32 läuft in einer VM. Das Durchreichen klappt aber noch nicht. Habe nun eine leeren Filter erstellt, aber die VM bekommt keines der USB-Geräte vom Host zu Gesicht. lsusb zeigt sie natürlich im Host. |
Anmeldungsdatum: Beiträge: 19610 Wohnort: Schleswig-Holstein |
Das Extension Pack ist Installiert für USB Unterstützung? Bist du in der Gruppe vboxuser? |
Supporter, Wikiteam
(Themenstarter)
Anmeldungsdatum: Beiträge: 17660 Wohnort: in deinem Browser, hier auf dem Bildschirm |
Extension Pack habe ich nun installiert. Bin nun auch in der Gruppe. Ich habe jetzt den Scanner hinzugefügt. Er wird im Windows erkannt, es fehlt aber ein Treiber. Haben den von der Epson-Seite für Win 7 genommen und installiert, wurde nach einem Neustart auch erkannt. Ich habe nun im Windows mit Fax und Scan 3 mal gescannt, alles normal. Liegt also nicht an der Hardware (habe gerade geschaut, gibt noch so einen auf eBay 😈). |
Anmeldungsdatum: Beiträge: 19610 Wohnort: Schleswig-Holstein |
Dann bleibt nur noch das selbst Kompilieren des plustek Treibers.Mein Vorschlag – nicht jünger als 1.25 https://gitlab.com/sane-project/backends/-/tags |
Anmeldungsdatum: Beiträge: 19610 Wohnort: Schleswig-Holstein |
sudo apt -s install build-essential gettext libusb-dev linux-headers-generic mkdir -p ~/src cd ~/src wget https://gitlab.com/sane-project/backends/uploads/c2e9cd2bcae2f13fd54dc58b755e6fbe/sane-backends-1.0.25.tar.gz tar -zxvf sane-backends-1.0.25.tar.gz cd ~/src/sane-backends-1.0.25 BACKENDS="plustek" ./configure make && sudo make install bis hier erst mal .... |
Supporter, Wikiteam
(Themenstarter)
Anmeldungsdatum: Beiträge: 17660 Wohnort: in deinem Browser, hier auf dem Bildschirm |
So, habe nun mal unter Debian 10 Buster i386 auf meinem D600 probiert. Funktioniert einwandfrei. djkuhpisse@debian-d600:~$ cat /etc/sane.d/plustek.conf # Plustek-SANE Backend configuration file # For use with LM9831/2/3 based USB scanners # # each device needs at least two lines: # - [usb] vendor-ID and product-ID # - device devicename # i.e. for Plustek (0x07B3) UT12/16/24 (0x0017) # [usb] 0x07B3 0x0017 # device /dev/usbscanner # or # device libusb:bbb:ddd # where bbb is the busnumber and ddd the device number # make sure that your user has access to /proc/bus/usb/bbb/ddd # # additionally you can specify some options # warmup, lOffOnEnd, lampOff # # For autodetection use # [usb] # device /dev/usbscanner # # or simply # [usb] # # or if you want a specific device but you have no idea about the # device node or you use libusb, simply set vendor- and product-ID # [usb] 0x07B3 0x0017 # device auto # # NOTE: autodetection is safe, as it uses the info it got # from the USB subsystem. If you're not using the # autodetection, you MUST have attached that device # at your USB-port, that you have specified... # [usb] # # options for the previous USB entry # # switch lamp off after xxx secs, 0 disables the feature # (can also be set via frontend) option lampOff 300 # warmup period in seconds, 0 means no warmup, -1 means auto-warmup # (can also be set via frontend) option warmup -1 # 0 means leave lamp-status untouched, not 0 means switch off # on sane_close # (can also be set via frontend) option lOffOnEnd 1 # # options to tweak the image start-position # (WARNING: there's no internal range check!!!) # # for the normal scan area # option posOffX 0 option posOffY 0 # for transparencies option tpaOffX 0 option tpaOffY 0 # for negatives option negOffX 0 option negOffY 0 # # for setting the calibration strip position # (WARNING: there's no internal range check!!!) # -1 means use built in # (can also be set via frontend) option posShadingY -1 option tpaShadingY -1 option negShadingY -1 # # to invert the negatives, 0 disables the feature # option invertNegatives 0 # # to disable the internal sensor speedup function, # 1 disables the feature # option disableSpeedup 0 # # to save/restore coarse calibration data # (can also be set via frontend) option cacheCalData 0 # # use alternate calibration routines # option altCalibration 0 # # for skipping whole calibration step # option skipCalibration 0 # # for skipping entire fine calibration step # coarse calibration is done # option skipFine 0 # # discard the result of the fine white calibration # option skipFineWhite 0 # # some scanners have a dark calibration strip, in # general this one should be used for calibration. # As this could cause some trouble, this option # overrides that and the dark calibration will be # done by switching the lamp off # option skipDarkStrip 0 # for replacing the gain values found during coarse # calibration # (can also be set via frontend) option red_gain -1 option green_gain -1 option blue_gain -1 # for replacing the offset values found during coarse # calibration # (can also be set via frontend) option red_offset -1 option green_offset -1 option blue_offset -1 # # for replacing the default lampoff settings, this # works only for CIS devices like CanoScan LiDE20 # (can also be set via frontend) option red_lampoff -1 option green_lampoff -1 option blue_lampoff -1 # # for adjusting the default gamma values # (can also be set via frontend) option redGamma 1.0 option greenGamma 1.0 option blueGamma 1.0 option grayGamma 1.0 # # to enable TPA (EPSON or UMAX, if autodetection fails) # 0 means default behaviour as specified in the internal tables # 1 means enable (needed for UMAX 3450) option enableTPA 0 # # model override functionality, currently only available for # Mustek devices, using NSCs' vendor ID: 0x0400 and # also their product ID: 0x1000 (LM9831) 0x1001 (LM9832) # # mov/PID | 0x1000 | 0x1001 # --------------------------------------- # 0 (default)| BearPaw1200 | BearPaw 2400 # 1 | ignored | BearPaw 1200 # option mov 0 # # and of course the device-name # # device /dev/usbscanner device auto # # to define a new device, start with a new section: # [usb] # djkuhpisse@debian-d600:~$ |
Anmeldungsdatum: Beiträge: 19610 Wohnort: Schleswig-Holstein |
Das die plustek.conf die selbe ist sollte klar sein und sich schnell prüfen lassen 😛 Deine *buntu ist auch 32 Bit? |
Supporter, Wikiteam
(Themenstarter)
Anmeldungsdatum: Beiträge: 17660 Wohnort: in deinem Browser, hier auf dem Bildschirm |
Nein, 64-Bit 19.10. Ich teste jetzt mal mit 18.04 64-Bit und 18.04 32-Bit. |