Grüß euch.
So, ich hab heute endlich den Schritt gewagt mal was anderes als Windows zu verwenden. Leider wurde ich prompt bestraft.
Also ich hab ein Problem mit der WLAN Verbindung. Rechts oben seh ich zwar das Zeichen für WLAN, mach ich einen rechts Klick drauf steht da für die WLAN Karte: "device not ready (firmwaremissing)".
Jetzt hab ich aber die Treiber aus diesem Thread installiert: http://forum.ubuntuusers.de/topic/ibm-t42-mit-intel-ipw2200-falsches-passwort/
Das sollten ja die richtigen sein.
Hier mal die Ausgaben:
Linux ubuntu 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:56:25 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux
00:19.0 Ethernet controller [0200]: Intel Corporation 82562GT 10/100 Network Connection [8086:10c4] (rev 03) Subsystem: Hewlett-Packard Company Device [103c:30d8] Kernel driver in use: e1000e -- 10:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11a/b/g [14e4:4312] (rev 02) Subsystem: Hewlett-Packard Company Broadcom 802.11a/b/g WLAN [103c:1371] Kernel driver in use: b43-pci-bridge
auto lo iface lo inet loopback
# Generated by NetworkManager
127.0.0.1 localhost 127.0.1.1 ubuntu.ubuntu-domain ubuntu # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters
eth0 Link encap:Ethernet HWaddr 00:1a:4b:93:b6:1d UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:22 Memory:e4600000-e4620000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:64 errors:0 dropped:0 overruns:0 frame:0 TX packets:64 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5120 (5.1 KB) TX bytes:5120 (5.1 KB)
Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface
wlan0 14 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Channel 14 : 2.484 GHz
lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Network is down
# This file was automatically generated by the /lib/udev/write_net_rules # program, run by the persistent-net-generator.rules rules file. # # You can modify it, as long as you keep each rule on a single # line, and change only the value of the NAME= key. # PCI device 0x8086:0x10c4 (e1000e) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:1a:4b:93:b6:1d", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" # PCI device 0x14e4:0x4312 (b43-pci-bridge) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:1a:73:f3:ac:d4", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"
Ausgaben laut: http://forum.ubuntuusers.de/topic/vor-dem-erstellen-eines-neuen-beitrags-bitte-/
Vielleicht kann mir wer helfen ☹. Probier jetzt sicher schon 5h und will schlafen gehen 😛!
MfG, Julian