Hallo ich hab meine 2 wichtigsten Festplatten von einem live system gecheckt..
Ich kann aber mit den erhaltenen Ergebnissen nichts Anfangen,wie der Zustand der Platten ist:
ubuntu@ubuntu:~$ sudo smartctl -a /dev/nvme0n1 smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.18.0-10-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: Samsung SSD 960 EVO 250GB Serial Number: S3ESNX0J208448N Firmware Version: 3B7QCXE7 PCI Vendor/Subsystem ID: 0x144d IEEE OUI Identifier: 0x002538 Total NVM Capacity: 250,059,350,016 [250 GB] Unallocated NVM Capacity: 0 Controller ID: 2 Number of Namespaces: 1 Namespace 1 Size/Capacity: 250,059,350,016 [250 GB] Namespace 1 Utilization: 13,614,678,016 [13.6 GB] Namespace 1 Formatted LBA Size: 512 Local Time is: Sat Feb 16 10:28:05 2019 UTC Firmware Updates (0x16): 3 Slots, no Reset required Optional Admin Commands (0x0007): Security Format Frmw_DL Optional NVM Commands (0x001f): Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Maximum Data Transfer Size: 512 Pages Warning Comp. Temp. Threshold: 77 Celsius Critical Comp. Temp. Threshold: 79 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 6.04W - - 0 0 0 0 0 0 1 + 5.09W - - 1 1 1 1 0 0 2 + 4.08W - - 2 2 2 2 0 0 3 - 0.0400W - - 3 3 3 3 210 1500 4 - 0.0050W - - 4 4 4 4 2200 6000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02, NSID 0x1) Critical Warning: 0x00 Temperature: 35 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 1% Data Units Read: 9,899,417 [5.06 TB] Data Units Written: 7,274,234 [3.72 TB] Host Read Commands: 217,396,525 Host Write Commands: 77,650,808 Controller Busy Time: 398 Power Cycles: 4,584 Power On Hours: 764 Unsafe Shutdowns: 233 Media and Data Integrity Errors: 0 Error Information Log Entries: 1,951 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 35 Celsius Temperature Sensor 2: 41 Celsius Error Information (NVMe Log 0x01, max 64 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS 0 1951 0 0x00a0 0x4212 0x028 0 - - 1 1950 0 0x0002 0x4004 0x028 0 0 - 2 1949 0 0x0002 0x4004 0x028 0 0 - 3 1948 0 0x0002 0x4004 0x028 0 0 - 4 1947 0 0x0002 0x4004 0x028 0 0 - 5 1946 0 0x00b6 0x4212 0x028 0 - - 6 1945 0 0x0002 0x4004 0x028 0 0 - 7 1944 0 0x0002 0x4004 0x028 0 0 - 8 1943 0 0x00a4 0x4212 0x028 0 - - 9 1942 0 0x0002 0x4004 0x028 0 0 - 10 1941 0 0x0084 0x4212 0x028 0 - - 11 1940 0 0x0002 0x4004 0x028 0 0 - 12 1939 0 0x00a2 0x4212 0x028 0 - - 13 1938 0 0x0002 0x4004 0x028 0 0 - 14 1937 0 0x0002 0x4004 0x028 0 0 - 15 1936 0 0x0002 0x4004 0x028 0 0 - ... (48 entries not shown) ubuntu@ubuntu:~$
//
ubuntu@ubuntu:~$ sudo smartctl -a /dev/sda smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.18.0-10-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Samsung SSD 860 EVO 1TB Serial Number: S3Z9NB0KB21600F LU WWN Device Id: 5 002538 e409eb5b7 Firmware Version: RVT02B6Q User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: Unknown(0x09fc), ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Feb 16 10:34:41 2019 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 249) Self-test routine in progress... 90% of test remaining. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 504 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 612 177 Wear_Leveling_Count 0x0013 099 099 000 Pre-fail Always - 2 179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0 181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0 182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0 183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0032 066 063 000 Old_age Always - 34 195 Hardware_ECC_Recovered 0x001a 200 200 000 Old_age Always - 0 199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0 235 Unknown_Attribute 0x0012 099 099 000 Old_age Always - 97 241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 2834879269 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 36447232 36512767 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. ubuntu@ubuntu:~$
Der Test ist auch gefühlt viel zu schnell durchgelaufen.
Kann jemand etwas dazu sagen, wie der Zustand ist?