ubuntuusers.de

celiz schrieb:

Danke eishailiga!

Habe das Problem lösen können (http://forum.ubuntuusers.de/topic/dvb-t-af9015-linux-treiber/2/#post-1353223)

Beim umherstöbern habe ich im wiki von linuxtv heraus gelesen dass der tuner ab 2.6.30 endlich im Kernel landen soll. Dann wär's endlich vorbei mit dieser ewigen Hatz, diesen Treiber bzw. FW jedes mal nachzuladen.

Danke dir, für deine schnelle Antwort!

Hallo,

ich hab das gleiche Problem. Falls jemand das Archiv (tip.tar.gz) noch irgendo rumfliegen hat, wäre ich sehr dankbar, wenn es jemand irgendwo hochladen könnte.

Unter dem folgenden Link lässt's sich runter laden;

http://linuxtv.org/hg/~anttip/af9015/archive/tip.tar.gz

MfG

celiz schrieb:

Unter dem folgenden Link lässt's sich runter laden;

http://linuxtv.org/hg/~anttip/af9015/archive/tip.tar.gz

MfG

Danke,

hat funktioniert

Hallo,

ich verzweifel gerade an diesem Stick. Er wird nicht erkannt, obwohl ich die FW in den Ordner /lib/firmware kopiert habe.

lsusb:

Bus 001 Device 009: ID 0ccd:0086 TerraTec Electronic GmbH 
Bus 001 Device 005: ID 04f2:b008 Chicony Electronics Co., Ltd 
Bus 001 Device 003: ID 1307:0165 Transcend Information, Inc. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 413c:3010 Dell Computer Corp. Optical Wheel Mouse
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

dmesg:

[  638.112156] usb 1-1: new high speed USB device using ehci_hcd and address 9
[  638.254755] usb 1-1: configuration #1 chosen from 1 choice

Es ist wohl die erste Version von dem Stick (Mülleimer neben dem CE-Zeichen und HWID 0086) der Out of the box laufen sollte. Unter Windows wird er erkannt. Ist also nicht defekt. Ich versiche ihn unter 9.04 ans Laufen zu bekommen.

Kann mir jemand weiterhelfen, bitte?

Schonmal vielen Dank!

Viele Grüße

Timo

Probieren kannst du mal dieses, ist eine Anleitung aus unserem Wiki...

wget http://media.ubuntuusers.de/forum/attachments/1862452/xc3028-v27-1.sh

chmod +x xc3028-v27-1.sh

./xc3028-v27-1.sh

für 32bit

wget http://jiemeb.free.fr/pinnacle/em28xx_28-15_i386.deb

dpkg -i em28xx_28-15_i386.deb

oder aber für 64 bit

wget http://jiemeb.free.fr/pinnacle/em28xx_28-15_amd64.deb

dpkg -i em28xx_28-15_amd64.deb

und dann noch

wget http://jiemeb.free.fr/pinnacle/cleanEm28xx.sh

chmod +x cleanEm28xx.sh

./cleanEm28xx.sh

sudo reboot

und nach dem Neustart poste mal die Ausgabe von

dmesg | grep -i dvb

Danke für deine Antwort. Aber leider kein Erfolg. dmesg bring mit den Parametern keine Ausgabe und wenn ich die Parameter weglasse, kann ich keinen Unterschied zu gestern entdecken. Und nun ?

ich habe mit dem Teil auch ein kleines Problem....und zwar wenn ich das Teil neu einstöpsel am USB erscheint folgendes

chef@chef-desktop:~$ dmesg | grep -i dvb
[   13.519243] dvb-usb: found a 'TerraTec Cinergy T USB XE' in cold state, will try to load a firmware
[   14.454637] dvb-usb: did not find the firmware file. (af9005.fw) Please see linux/Documentation/dvb/ for more details on firmware-problems. (-2)
[   14.454652] dvb_usb_af9005: probe of 1-3.1:1.0 failed with error -2
[   14.454669] usbcore: registered new interface driver dvb_usb_af9005
chef@chef-desktop:~$ 

Es kommt die Fehlermeldung in cold state Ich muss dann immer erst Windows starten, einmal die Original soft benutzen und wen ich dann Ubuntu (egal welche Version) starte klappt das dann erscheint in warm state ..

chef@chef-desktop:~$ dmesg | grep -i dvb
[   14.906187] dvb-usb: found a 'TerraTec Cinergy T USB XE' in warm state.
[   14.906225] dvb-usb: will use the device's hardware PID filter (table count: 32).
[   14.907327] DVB: registering new adapter (TerraTec Cinergy T USB XE)
[   14.908430] DVB: registering adapter 0 frontend 0 (AF9005 USB DVB-T)...
[   14.908456] dvb-usb: TerraTec Cinergy T USB XE successfully initialized and connected.
[   14.908471] usbcore: registered new interface driver dvb_usb_af9005
chef@chef-desktop:~$

Hallihallo, nachdem ich nun lange diesen Stick zur Seite gelegt habe, da ich verzweifel war, dass ich den Stick nicht zum Laufen bringen konnte, habe ich mich nun nocheinmal dran gesetzt und versucht den DVD-T Stick der 2. Generation unter HArdy Heron zum Laufen zu bringen. Leider ohne Erfolg. Ich scheitere gleich am Anfang. Habe die Treiber heruntergeladen und entpackt. Nun wollte ich die entpackten Daten so wie es in der Anleitung steht in das VErzeichnis dvb_cinergy verschieben. Doch hier bekomme ich immer folgende Meldung:

mv: Aufruf von stat für „Cinergy T USB XE MKII/Fedora Core Release 6/“ nicht möglich: No such file or directory

Ich habe mal nachgesehen mit dir zeigt er mir folgenden Inhalt an, der Ordner dvb_cinergy scheint also zu existieren. Ich weiß einfach nicht mehr weiter, was mache ich denn falsch? ☹

Würde mich riesig über Eure Hilfe freuen!!!

Stevi

Ubuntu 9.10 64 bit - Erfolg!

Hardware Treiber installieren, Kaffeine starten, ggf. noch "w-scan" nachinstallieren, Sendersuchlauf und ab gehts. Version: T USB XE II

Gruß - was lange wärt ist nun auch gut! ☺

Hi,

Ich hab seit dem Update auf Kubuntu 9.10 (32bit) ein Problem mit meiner "Cinergy HT USB XE" (ID 0ccd:0058). Die Karte wird erkannt und (laut dmesg) auch korrekt initialisiert. Allerdings stürzt jedes Programm das auf die Karte zugreift ab oder friert ein.

mfg, guest

edit: Mittlerweile läuft der Stick mit v4l-dvb.

Hallo ich habe mir auch den Stick geholt, und habe auch ubuntu, aber kenne mich nicht damit aus, kann mir jemand in einfachen schritten erklären wie ich das mache, das der installiert wird und er auch funktioniert danach !?...

Hi!

Willkommen im Forum!

Schau mal in unser Wiki, da gibts zu sehr vielen Fragen die richtgen Antworten, speziell zu deinem Stick ist unter Cinergy T USB XE alles erläutert.

so long
hank

amin@ibm:~/Desktop$ dmesg

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.31-17-generic (buildd@palmer) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu8) ) #54-Ubuntu SMP Thu Dec 10 16:20:31 UTC 2009 (Ubuntu 2.6.31-17.54-generic)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000000feb0000 (usable)
[    0.000000]  BIOS-e820: 000000000feb0000 - 000000000fefc000 (ACPI data)
[    0.000000]  BIOS-e820: 000000000fefc000 - 000000000fefd000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000000fefd000 - 000000000ff00000 (reserved)
[    0.000000]  BIOS-e820: 000000000ff00000 - 000000000ff80000 (usable)
[    0.000000]  BIOS-e820: 000000000ff80000 - 0000000010000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[    0.000000] DMI present.
[    0.000000] last_pfn = 0xff80 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-C7FFF write-protect
[    0.000000]   C8000-E3FFF uncachable
[    0.000000]   E4000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask FF0000000 write-back
[    0.000000]   1 disabled
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820 update range: 0000000000002000 - 0000000000006000 (usable) ==> (reserved)
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000002000 (usable)
[    0.000000]  modified: 0000000000002000 - 0000000000006000 (reserved)
[    0.000000]  modified: 0000000000006000 - 000000000009f800 (usable)
[    0.000000]  modified: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000000feb0000 (usable)
[    0.000000]  modified: 000000000feb0000 - 000000000fefc000 (ACPI data)
[    0.000000]  modified: 000000000fefc000 - 000000000fefd000 (ACPI NVS)
[    0.000000]  modified: 000000000fefd000 - 000000000ff00000 (reserved)
[    0.000000]  modified: 000000000ff00000 - 000000000ff80000 (usable)
[    0.000000]  modified: 000000000ff80000 - 0000000010000000 (reserved)
[    0.000000]  modified: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  modified: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  modified: 00000000ff800000 - 00000000ffc00000 (reserved)
[    0.000000]  modified: 00000000fff00000 - 0000000100000000 (reserved)
[    0.000000] initial memory mapped : 0 - 00c00000
[    0.000000] init_memory_mapping: 0000000000000000-000000000ff80000
[    0.000000] Using x86 segment limits to approximate NX protection
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 000fc00000 page 2M
[    0.000000]  000fc00000 - 000ff80000 page 4k
[    0.000000] kernel direct mapping tables up to ff80000 @ 7000-c000
[    0.000000] RAMDISK: 0b7f9000 - 0bf43a46
[    0.000000] ACPI: RSDP 000f5fc0 00014 (v00 PTLTD )
[    0.000000] ACPI: RSDT 0fef87f8 00030 (v01 PTLTD    RSDT   060400D0  LTP 00000000)
[    0.000000] ACPI: FACP 0fefbf0a 00074 (v01 IBM    MARLIN   060400D0 PTL  00000001)
[    0.000000] ACPI: DSDT 0fef8828 036E2 (v01    IBM   Marlin 060400D0 MSFT 0100000D)
[    0.000000] ACPI: FACS 0fefcfc0 00040
[    0.000000] ACPI: APIC 0fefbf7e 0005A (v01 PTLTD  	 APIC   060400D0  LTP 00000000)
[    0.000000] ACPI: BOOT 0fefbfd8 00028 (v01 PTLTD  $SBFTBL$ 060400D0  LTP 00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 255MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 0ff80000
[    0.000000]   low ram: 0 - 0ff80000
[    0.000000]   node 0 low ram: 00000000 - 0ff80000
[    0.000000]   node 0 bootmap 00008000 - 00009ff0
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 000ff80000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00008a80a0]    TEXT DATA BSS ==> [0000100000 - 00008a80a0]
[    0.000000]   #4 [000b7f9000 - 000bf43a46]          RAMDISK ==> [000b7f9000 - 000bf43a46]
[    0.000000]   #5 [000009f800 - 0000100000]    BIOS reserved ==> [000009f800 - 0000100000]
[    0.000000]   #6 [00008a9000 - 00008ac0ac]              BRK ==> [00008a9000 - 00008ac0ac]
[    0.000000]   #7 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
[    0.000000]   #8 [0000008000 - 000000a000]          BOOTMAP ==> [0000008000 - 000000a000]
[    0.000000] found SMP MP-table at [c00f5f70] f5f70
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x0000ff80
[    0.000000]   HighMem  0x0000ff80 -> 0x0000ff80
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[4] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00000002
[    0.000000]     0: 0x00000006 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0000feb0
[    0.000000]     0: 0x0000ff00 -> 0x0000ff80
[    0.000000] On node 0 totalpages: 65227
[    0.000000] free_area_init_node: node 0, pgdat c0784960, node_mem_map c1000000
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3963 pages, LIFO batch:0
[    0.000000]   Normal zone: 479 pages used for memmap
[    0.000000]   Normal zone: 60753 pages, LIFO batch:15
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 24
[    0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 000000000feb0000 - 000000000fefc000
[    0.000000] PM: Registered nosave memory: 000000000fefc000 - 000000000fefd000
[    0.000000] PM: Registered nosave memory: 000000000fefd000 - 000000000ff00000
[    0.000000] Allocating PCI resources starting at 10000000 (gap: 10000000:eec00000)
[    0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages at c1202000, static data 35612 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64716
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.31-17-generic root=UUID=d8b66e7f-ba79-42bd-a2b9-0d6ffb69efc6 ro quiet splash
[    0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] allocated 1308160 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Initializing HighMem for node 0 (00000000:00000000)
[    0.000000] Memory: 241608k/261632k available (4566k kernel code, 18952k reserved, 2142k data, 540k init, 0k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff1d000 - 0xfffff000   ( 904 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xd0780000 - 0xff7fe000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xcff80000   ( 255 MB)
[    0.000000]       .init : 0xc078e000 - 0xc0815000   ( 540 kB)
[    0.000000]       .data : 0xc0575a64 - 0xc078d408   (2142 kB)
[    0.000000]       .text : 0xc0100000 - 0xc0575a64   (4566 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:2304 nr_irqs:256
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 1595.131 MHz processor.
[    0.001517] Console: colour VGA+ 80x25
[    0.001526] console [tty0] enabled
[    0.004016] Calibrating delay loop (skipped), value calculated using timer frequency.. 3190.26 BogoMIPS (lpj=6380524)
[    0.004059] Security Framework initialized
[    0.004106] AppArmor: AppArmor initialized
[    0.004123] Mount-cache hash table entries: 512
[    0.004424] Initializing cgroup subsys ns
[    0.004437] Initializing cgroup subsys cpuacct
[    0.004448] Initializing cgroup subsys memory
[    0.004467] Initializing cgroup subsys freezer
[    0.004473] Initializing cgroup subsys net_cls
[    0.004511] CPU: Trace cache: 12K uops, L1 D cache: 8K
[    0.004519] CPU: L2 cache: 256K
[    0.004524] CPU: Hyper-Threading is disabled
[    0.004533] mce: CPU supports 4 MCE banks
[    0.004555] CPU0: Thermal monitoring enabled (TM1)
[    0.004577] Performance Counters: no PMU driver, software counters only.
[    0.004592] Checking 'hlt' instruction... OK.
[    0.021547] SMP alternatives: switching to UP code
[    0.036053] Freeing SMP alternatives: 19k freed
[    0.036102] ACPI: Core revision 20090521
[    0.052521] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.093165] CPU0: Intel(R) Pentium(R) 4 CPU 1.60GHz stepping 02
[    0.096001] Brought up 1 CPUs
[    0.096001] Total of 1 processors activated (3190.26 BogoMIPS).
[    0.096001] CPU0 attaching NULL sched-domain.
[    0.096001] Booting paravirtualized kernel on bare hardware
[    0.096001] regulator: core version 0.5
[    0.096001] Time: 11:16:17  Date: 01/30/10
[    0.096001] NET: Registered protocol family 16
[    0.096001] EISA bus registered
[    0.096001] ACPI: bus type pci registered
[    0.096001] PCI: PCI BIOS revision 2.10 entry at 0xfd933, last bus=2
[    0.096001] PCI: Using configuration type 1 for base access
[    0.096897] bio: create slab <bio-0> at 0
[    0.098031] ACPI: EC: Look up EC in DSDT
[    0.120468] ACPI: Interpreter enabled
[    0.120483] ACPI: (supports S0 S1 S3 S4 S5)
[    0.120534] ACPI: Using IOAPIC for interrupt routing
[    0.166333] ACPI: No dock devices found.
[    0.168444] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.168560] pci 0000:00:00.0: reg 10 32bit mmio: [0xf4000000-0xf7ffffff]
[    0.168809] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[    0.168816] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH4 GPIO
[    0.168878] pci 0000:00:1f.1: reg 20 io port: [0x1800-0x180f]
[    0.168958] pci 0000:00:1f.2: reg 20 io port: [0x1820-0x183f]
[    0.169040] pci 0000:00:1f.3: reg 20 io port: [0x1810-0x181f]
[    0.169117] pci 0000:00:1f.4: reg 20 io port: [0x1840-0x185f]
[    0.169174] pci 0000:00:1f.5: reg 10 io port: [0x1c00-0x1cff]
[    0.169186] pci 0000:00:1f.5: reg 14 io port: [0x1880-0x18bf]
[    0.169285] pci 0000:01:00.0: reg 10 32bit mmio: [0xf0000000-0xf0ffffff]
[    0.169296] pci 0000:01:00.0: reg 14 32bit mmio: [0xf8000000-0xf9ffffff]
[    0.169324] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x00ffff]
[    0.169406] pci 0000:00:01.0: bridge 32bit mmio: [0xf0000000-0xf1ffffff]
[    0.169414] pci 0000:00:01.0: bridge 32bit mmio pref: [0xf8000000-0xfaffffff]
[    0.169479] pci 0000:02:08.0: reg 10 32bit mmio: [0xf2000000-0xf2000fff]
[    0.169491] pci 0000:02:08.0: reg 14 io port: [0x2000-0x203f]
[    0.169545] pci 0000:02:08.0: supports D1 D2
[    0.169549] pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.169557] pci 0000:02:08.0: PME# disabled
[    0.169603] pci 0000:00:1e.0: transparent bridge
[    0.169611] pci 0000:00:1e.0: bridge io port: [0x2000-0x2fff]
[    0.169619] pci 0000:00:1e.0: bridge 32bit mmio: [0xf2000000-0xf20fffff]
[    0.169639] pci_bus 0000:00: on NUMA node 0
[    0.169648] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.169807] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[    0.169902] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SLOT._PRT]
[    0.201957] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[    0.202141] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[    0.202315] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.202493] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[    0.202675] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[    0.202854] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.203037] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.203221] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[    0.203686] SCSI subsystem initialized
[    0.203871] libata version 3.00 loaded.
[    0.204116] usbcore: registered new interface driver usbfs
[    0.204159] usbcore: registered new interface driver hub
[    0.204229] usbcore: registered new device driver usb
[    0.204566] ACPI: WMI: Mapper loaded
[    0.204571] PCI: Using ACPI for IRQ routing
[    0.204874] Bluetooth: Core ver 2.15
[    0.204993] NET: Registered protocol family 31
[    0.204998] Bluetooth: HCI device and connection manager initialized
[    0.205005] Bluetooth: HCI socket layer initialized
[    0.205009] NetLabel: Initializing
[    0.205013] NetLabel:  domain hash size = 128
[    0.205016] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.205045] NetLabel:  unlabeled traffic allowed by default
[    0.209202] pnp: PnP ACPI init
[    0.209263] ACPI: bus type pnp registered
[    0.277253] pnp: PnP ACPI: found 15 devices
[    0.277263] ACPI: ACPI bus type pnp unregistered
[    0.277270] PnPBIOS: Disabled by ACPI PNP
[    0.277315] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[    0.277324] system 00:01: ioport range 0xfe00-0xfe00 has been reserved
[    0.277331] system 00:01: ioport range 0x800-0x84f has been reserved
[    0.277337] system 00:01: ioport range 0x1000-0x107f has been reserved
[    0.277343] system 00:01: ioport range 0x1180-0x11bf has been reserved
[    0.277353] system 00:01: iomem range 0xfec00000-0xfec000ff could not be reserved
[    0.312248] AppArmor: AppArmor Filesystem Enabled
[    0.312306] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.312311] pci 0000:00:01.0:   IO window: disabled
[    0.312321] pci 0000:00:01.0:   MEM window: 0xf0000000-0xf1ffffff
[    0.312328] pci 0000:00:01.0:   PREFETCH window: 0xf8000000-0xfaffffff
[    0.312336] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[    0.312343] pci 0000:00:1e.0:   IO window: 0x2000-0x2fff
[    0.312352] pci 0000:00:1e.0:   MEM window: 0xf2000000-0xf20fffff
[    0.312359] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.312387] pci 0000:00:1e.0: setting latency timer to 64
[    0.312399] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.312406] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.312412] pci_bus 0000:01: resource 1 mem: [0xf0000000-0xf1ffffff]
[    0.312418] pci_bus 0000:01: resource 2 pref mem [0xf8000000-0xfaffffff]
[    0.312423] pci_bus 0000:02: resource 0 io:  [0x2000-0x2fff]
[    0.312429] pci_bus 0000:02: resource 1 mem: [0xf2000000-0xf20fffff]
[    0.312434] pci_bus 0000:02: resource 3 io:  [0x00-0xffff]
[    0.312439] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
[    0.312520] NET: Registered protocol family 2
[    0.312738] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.313362] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.313449] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.313536] TCP: Hash tables configured (established 8192 bind 8192)
[    0.313543] TCP reno registered
[    0.313732] NET: Registered protocol family 1
[    0.313893] Trying to unpack rootfs image as initramfs...
[    0.747650] Freeing initrd memory: 7466k freed
[    0.766372] Simple Boot Flag at 0x72 set to 0x1
[    0.766541] cpufreq-nforce2: No nForce2 chipset.
[    0.766603] Scanning for low memory corruption every 60 seconds
[    0.766883] audit: initializing netlink socket (disabled)
[    0.766925] type=2000 audit(1264850176.763:1): initialized
[    0.781269] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.784357] VFS: Disk quotas dquot_6.5.2
[    0.784511] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.785822] fuse init (API version 7.12)
[    0.786027] msgmni has been set to 487
[    0.786590] alg: No test for stdrng (krng)
[    0.786633] io scheduler noop registered
[    0.786638] io scheduler anticipatory registered
[    0.786642] io scheduler deadline registered
[    0.786790] io scheduler cfq registered (default)
[    0.786889] pci 0000:01:00.0: Boot video device
[    0.786923] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[    0.787100] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.787152] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.787406] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    0.787416] ACPI: Power Button [PWRF]
[    0.787539] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0A03:00/PNP0C0C:00/input/input1
[    0.787545] ACPI: Power Button [PWRB]
[    0.787881] processor LNXCPU:00: registered as cooling_device0
[    0.787951] ACPI: Processor [CPU0] (supports 8 throttling states)
[    0.818048] Switched to high resolution mode on CPU 0
[    0.823569] thermal LNXTHERM:01: registered as thermal_zone0
[    0.823595] ACPI: Thermal Zone [THM0] (18 C)
[    0.823749] isapnp: Scanning for PnP cards...
[    1.178072] isapnp: No Plug & Play device found
[    1.180549] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.180731] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.180870] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.181510] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.181707] 00:0d: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.183745] brd: module loaded
[    1.184770] loop: module loaded
[    1.184997] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[    1.185261] ata_piix 0000:00:1f.1: version 2.13
[    1.185398] ata_piix 0000:00:1f.1: setting latency timer to 64
[    1.185639] scsi0 : ata_piix
[    1.185906] scsi1 : ata_piix
[    1.187898] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1800 irq 14
[    1.187905] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1808 irq 15
[    1.190018] Fixed MDIO Bus: probed
[    1.190111] PPP generic driver version 2.4.2
[    1.190370] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.190429] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.190457] uhci_hcd: USB Universal Host Controller Interface driver
[    1.190573]   alloc irq_desc for 19 on node -1
[    1.190579]   alloc kstat_irqs on node -1
[    1.190594] uhci_hcd 0000:00:1f.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    1.190612] uhci_hcd 0000:00:1f.2: setting latency timer to 64
[    1.190619] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[    1.190790] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
[    1.190850] uhci_hcd 0000:00:1f.2: irq 19, io base 0x00001820
[    1.191079] usb usb1: configuration #1 chosen from 1 choice
[    1.191148] hub 1-0:1.0: USB hub found
[    1.191172] hub 1-0:1.0: 2 ports detected
[    1.191289]   alloc irq_desc for 23 on node -1
[    1.191295]   alloc kstat_irqs on node -1
[    1.191309] uhci_hcd 0000:00:1f.4: PCI INT C -> GSI 23 (level, low) -> IRQ 23
[    1.191326] uhci_hcd 0000:00:1f.4: setting latency timer to 64
[    1.191332] uhci_hcd 0000:00:1f.4: UHCI Host Controller
[    1.191430] uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
[    1.191482] uhci_hcd 0000:00:1f.4: irq 23, io base 0x00001840
[    1.191693] usb usb2: configuration #1 chosen from 1 choice
[    1.191757] hub 2-0:1.0: USB hub found
[    1.191785] hub 2-0:1.0: 2 ports detected
[    1.192076] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PSM] at 0x60,0x64 irq 1,12
[    1.193675] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.193689] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.193849] mice: PS/2 mouse device common for all mice
[    1.194044] rtc_cmos 00:04: RTC can wake from S4
[    1.194129] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    1.194166] rtc0: alarms up to one month, y3k, 114 bytes nvram
[    1.194436] device-mapper: uevent: version 1.0.3
[    1.194733] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    1.194965] device-mapper: multipath: version 1.1.0 loaded
[    1.194974] device-mapper: multipath round-robin: version 1.0.0 loaded
[    1.195316] EISA: Probing bus 0 at eisa.0
[    1.195331] Cannot allocate resource for EISA slot 1
[    1.195337] Cannot allocate resource for EISA slot 2
[    1.195368] EISA: Detected 0 cards.
[    1.195504] cpuidle: using governor ladder
[    1.195510] cpuidle: using governor menu
[    1.196762] TCP cubic registered
[    1.197073] NET: Registered protocol family 10
[    1.198029] lo: Disabled Privacy Extensions
[    1.198699] NET: Registered protocol family 17
[    1.198766] Bluetooth: L2CAP ver 2.13
[    1.198770] Bluetooth: L2CAP socket layer initialized
[    1.198776] Bluetooth: SCO (Voice Link) ver 0.6
[    1.198779] Bluetooth: SCO socket layer initialized
[    1.198923] Bluetooth: RFCOMM TTY layer initialized
[    1.198930] Bluetooth: RFCOMM socket layer initialized
[    1.198934] Bluetooth: RFCOMM ver 1.11
[    1.199019] Using IPI No-Shortcut mode
[    1.199245] PM: Resume from disk failed.
[    1.199280] registered taskstats version 1
[    1.199486]   Magic number: 10:109:278
[    1.199547] tty tty15: hash matches
[    1.199637] rtc_cmos 00:04: setting system clock to 2010-01-30 11:16:18 UTC (1264850178)
[    1.199644] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.199648] EDD information not available.
[    1.213562] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    1.352945] ata1.00: ATA-5: MAXTOR 6L040J2, A93.0500, max UDMA/133
[    1.352953] ata1.00: 78177792 sectors, multi 16: LBA 
[    1.360530] ata2.00: ATAPI: 32X10, T.JA, max MWDMA2
[    1.360596] ata2.01: ATAPI: SAMSUNG CD-ROM  SC-148C, B100, max UDMA/33
[    1.368586] ata1.00: configured for UDMA/100
[    1.368864] scsi 0:0:0:0: Direct-Access     ATA      MAXTOR 6L040J2   A93. PQ: 0 ANSI: 5
[    1.369175] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.369307] sd 0:0:0:0: [sda] 78177792 512-byte logical blocks: (40.0 GB/37.2 GiB)
[    1.369420] sd 0:0:0:0: [sda] Write Protect is off
[    1.369427] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.369481] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.369801]  sda:
[    1.376383] ata2.00: configured for MWDMA2
[    1.376688]  sda1 sda2 <
[    1.384294] ata2.01: configured for UDMA/33
[    1.385737] scsi 1:0:0:0: CD-ROM            ATAPI    CD-R/RW 32X10    T.JA PQ: 0 ANSI: 5
[    1.387329]  sda5sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[    1.389355] Uniform CD-ROM driver Revision: 3.20
[    1.389610] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.389743] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.390174] scsi 1:0:1:0: CD-ROM            SAMSUNG  CD-ROM SC-148C   B100 PQ: 0 ANSI: 5
[    1.391682] sr1: scsi3-mmc drive: 20x/48x cd/rw xa/form2 cdda tray
[    1.391900] sr 1:0:1:0: Attached scsi CD-ROM sr1
[    1.392083] sr 1:0:1:0: Attached scsi generic sg2 type 5
[    1.403752]  sda6 >
[    1.404498] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.404538] Freeing unused kernel memory: 540k freed
[    1.405920] Write protecting the kernel text: 4568k
[    1.405985] Write protecting the kernel read-only data: 1836k
[    1.508113] usb 1-2: new full speed USB device using uhci_hcd and address 2
[    1.731932] usb 1-2: configuration #1 chosen from 1 choice
[    1.798637] Linux agpgart interface v0.103
[    1.868884] agpgart-intel 0000:00:00.0: Intel 845G Chipset
[    1.895385] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf4000000
[    1.895614] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[    1.895619] e100: Copyright(c) 1999-2006 Intel Corporation
[    1.895715]   alloc irq_desc for 20 on node -1
[    1.895721]   alloc kstat_irqs on node -1
[    1.895738] e100 0000:02:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    1.920118] e100 0000:02:08.0: PME# disabled
[    1.925191] Floppy drive(s): fd0 is 1.44M
[    1.960403] FDC 0 is a National Semiconductor PC87306
[    2.166565] e100: eth0: e100_probe: addr 0xf2000000, irq 20, MAC addr 00:09:6b:40:c4:a5
[    3.482878] PM: Starting manual resume from disk
[    3.482890] PM: Resume from partition 8:6
[    3.482894] PM: Checking hibernation image.
[    3.483313] PM: Resume from disk failed.
[    3.513275] EXT4-fs (sda1): barriers enabled
[    3.525425] kjournald2 starting: pid 306, dev sda1:8, commit interval 5 seconds
[    3.525473] EXT4-fs (sda1): delayed allocation enabled
[    3.525481] EXT4-fs: file extents enabled
[    3.528603] EXT4-fs: mballoc enabled
[    3.528640] EXT4-fs (sda1): mounted filesystem with ordered data mode
[    4.250081] type=1505 audit(1264850181.548:2): operation="profile_load" pid=329 name=/sbin/dhclient3
[    4.251086] type=1505 audit(1264850181.548:3): operation="profile_load" pid=329 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[    4.251627] type=1505 audit(1264850181.548:4): operation="profile_load" pid=329 name=/usr/lib/connman/scripts/dhclient-script
[    4.302816] type=1505 audit(1264850181.600:5): operation="profile_load" pid=330 name=/usr/bin/evince
[    4.320208] type=1505 audit(1264850181.620:6): operation="profile_load" pid=330 name=/usr/bin/evince-previewer
[    4.330480] type=1505 audit(1264850181.628:7): operation="profile_load" pid=330 name=/usr/bin/evince-thumbnailer
[    4.356284] type=1505 audit(1264850181.656:8): operation="profile_load" pid=332 name=/usr/lib/cups/backend/cups-pdf
[    4.357516] type=1505 audit(1264850181.656:9): operation="profile_load" pid=332 name=/usr/sbin/cupsd
[    4.368375] type=1505 audit(1264850181.668:10): operation="profile_load" pid=333 name=/usr/sbin/tcpdump
[    9.773561] Adding 979924k swap on /dev/sda6.  Priority:-1 extents:1 across:979924k 
[   10.156160] EXT4-fs (sda1): internal journal on sda1:8
[   10.424259] udev: starting version 147
[   10.449289] EXT4-fs (sda5): barriers enabled
[   10.451929] kjournald2 starting: pid 390, dev sda5:8, commit interval 5 seconds
[   10.452407] EXT4-fs (sda5): internal journal on sda5:8
[   10.452418] EXT4-fs (sda5): delayed allocation enabled
[   10.452424] EXT4-fs: file extents enabled
[   10.457658] EXT4-fs: mballoc enabled
[   10.457695] EXT4-fs (sda5): mounted filesystem with ordered data mode
[   11.572120] lp: driver loaded but no devices found
[   11.609562] parport_pc 00:0e: reported by Plug and Play ACPI
[   11.609652] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[   11.658165] ppdev: user-space parallel port driver
[   11.664905] psmouse serio1: ID: 10 00 64
[   11.684293] dvb-usb: found a 'TerraTec Cinergy T USB XE' in cold state, will try to load a firmware
[   11.684311] usb 1-2: firmware: requesting dvb-usb-af9015.fw
[   11.708467] lp0: using parport0 (interrupt-driven).
[   11.827120] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   11.849454] intel_rng: Firmware space is locked read-only. If you can't or
[   11.849458] intel_rng: don't want to disable this in firmware setup, and if
[   11.849461] intel_rng: you are certain that your system has a functional
[   11.849464] intel_rng: RNG, try using the 'no_fwh_detect' option.
[   12.021102] dvb-usb: did not find the firmware file. (dvb-usb-af9015.fw) Please see linux/Documentation/dvb/ for more details on firmware-problems. (-2)
[   12.021131] dvb_usb_af9015: probe of 1-2:1.0 failed with error -2
[   12.021183] usbcore: registered new interface driver dvb_usb_af9015
[   12.242414] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[   12.819794] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.070168]   alloc irq_desc for 17 on node -1
[   13.070176]   alloc kstat_irqs on node -1
[   13.070193] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   13.070231] Intel ICH 0000:00:1f.5: setting latency timer to 64
[   13.684075] intel8x0_measure_ac97_clock: measured 53454 usecs (2994 samples)
[   13.684084] intel8x0: clocking to 41135
[   14.758929] type=1505 audit(1264850192.056:11): operation="profile_replace" pid=774 name=/sbin/dhclient3
[   14.759945] type=1505 audit(1264850192.056:12): operation="profile_replace" pid=774 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[   14.762592] type=1505 audit(1264850192.060:13): operation="profile_replace" pid=774 name=/usr/lib/connman/scripts/dhclient-script
[   14.792815] type=1505 audit(1264850192.092:14): operation="profile_replace" pid=775 name=/usr/bin/evince
[   14.811010] type=1505 audit(1264850192.108:15): operation="profile_replace" pid=775 name=/usr/bin/evince-previewer
[   14.822222] type=1505 audit(1264850192.120:16): operation="profile_replace" pid=775 name=/usr/bin/evince-thumbnailer
[   14.842179] type=1505 audit(1264850192.140:17): operation="profile_replace" pid=777 name=/usr/lib/cups/backend/cups-pdf
[   14.843725] type=1505 audit(1264850192.140:18): operation="profile_replace" pid=777 name=/usr/sbin/cupsd
[   14.872351] type=1505 audit(1264850192.172:19): operation="profile_replace" pid=778 name=/usr/sbin/tcpdump
[   14.901861] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  533.000151] e100: eth0 NIC Link is Up 100 Mbps Full Duplex
[  533.000293] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  543.420046] eth0: no IPv6 routers present
[ 4155.000351] e100: eth0 NIC Link is Down
[ 5055.803077] UDF-fs: No VRS found
[ 5055.803089] UDF-fs: No partition found (1)
[ 5055.821685] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 5055.831230] ISOFS: changing to secondary root
[ 5147.000163] e100: eth0 NIC Link is Up 100 Mbps Full Duplex

Habe dsmeg eingegeben um zu gucken ob der angschlossen ist bzw erkannt worden ist ? was nun?

Hi!

Welche Firmware hast du verwendet?

[ 12.021102] dvb-usb: did not find the firmware file. (dvb-usb-af9015.fw) Please see linux/Documentation/dvb/ for more details on firmware-problems. (-2)

Diese sollte es sein: dvb-usb-af9015.fw, findest du im Artikel verlinkt, muss nach /lib/firmware

so long
hank

MusiB1tch schrieb:

Du solltest es mal mit

sudo make install

probieren.

Ich muss diesen Thread nochmal aufmachen, da bei mir dennoch der Fehler kommt make^[1]: *** [media-install] Fehler 1 make^[1]: Verlasse Verzeichnis '/home/tassilo/af9005/v4l' make: *** [install] Fehler 2