Hallo alle miteinander, voller Freude über die Behebung aller Probleme durch Kauf eines neuen PC wollte ich eigentlich mit der Installation von Ubuntu beginnen. Vorher habe ich in einem Probelauf mal mit der LiveCD gearbeitet. Dabei viel mir auf, dass weder mittels
ls
oder von
GParted
meine Sata FP erkannt wird. WindowsXP ist komplett installiert und funktioniert.
Angaben zu meinem PC:
Board: ASUS V3 P5G31 BIOS : AMI PCU :Intel Core 2 Duo
Beim Start der LiveCD erscheint eine Fehlermeldung:
Buffer I/O error on device fd=, logical block 0
Ansonsten habe ich keine nennenswerten Einschränkungen festgestellt.
Da diese Angaben vielleicht nicht ausreichen um einen hilfreichen Rat zur weiteren Vorgehensweise zu wagen, füge ich das Ergebnis von dmsg bei.
[ 47.083342] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0408e3fd 00000000 00000001 00000000 [ 47.083345] monitor/mwait feature present. [ 47.083347] CPU: L1 I cache: 32K, L1 D cache: 32K [ 47.083348] CPU: L2 cache: 6144K [ 47.083350] CPU: Physical Processor ID: 0 [ 47.083350] CPU: Processor Core ID: 1 [ 47.083351] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0408e3fd 00000000 00000001 00000000 [ 47.084183] CPU1: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 0a [ 47.084196] Total of 2 processors activated (11991.83 BogoMIPS). [ 47.084330] ENABLING IO-APIC IRQs [ 47.084486] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 47.266974] APIC calibration not consistent with PM Timer: 135ms instead of 100ms [ 47.266975] APIC delta adjusted to PM-Timer: 2081245 (2830457) [ 47.267044] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 47.287014] Brought up 2 CPUs [ 47.287031] CPU0 attaching sched-domain: [ 47.287032] domain 0: span 03 [ 47.287033] groups: 01 02 [ 47.287035] CPU1 attaching sched-domain: [ 47.287036] domain 0: span 03 [ 47.287036] groups: 02 01 [ 47.287164] net_namespace: 64 bytes [ 47.287170] Booting paravirtualized kernel on bare hardware [ 47.287423] Time: 17:33:39 Date: 10/01/08 [ 47.287439] NET: Registered protocol family 16 [ 47.287539] EISA bus registered [ 47.287541] ACPI: bus type pci registered [ 47.287672] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=4 [ 47.287673] PCI: Using configuration type 1 [ 47.287684] Setting up standard PCI resources [ 47.289847] ACPI: EC: Look up EC in DSDT [ 47.292655] ACPI: Interpreter enabled [ 47.292657] ACPI: (supports S0 S1 S3 S4 S5) [ 47.292665] ACPI: Using IOAPIC for interrupt routing [ 47.297105] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 47.297490] PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO [ 47.297492] PCI quirk: region 0480-04bf claimed by ICH6 GPIO [ 47.298001] PCI: Transparent bridge - 0000:00:1e.0 [ 47.298021] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 47.298098] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 47.298160] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] [ 47.298209] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT] [ 47.303328] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 47.303400] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 47.303471] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15) [ 47.303542] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 47.303612] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 47.303684] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 47.303755] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 47.303826] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 47.303895] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - CA, should be BD [20070126] [ 47.303904] Linux Plug and Play Support v0.97 (c) Adam Belay [ 47.303919] pnp: PnP ACPI init [ 47.303923] ACPI: bus type pnp registered [ 47.306419] pnp: PnP ACPI: found 19 devices [ 47.306421] ACPI: ACPI bus type pnp unregistered [ 47.306423] PnPBIOS: Disabled by ACPI PNP [ 47.306533] PCI: Using ACPI for IRQ routing [ 47.306535] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 47.338913] NET: Registered protocol family 8 [ 47.338915] NET: Registered protocol family 20 [ 47.338937] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 47.338941] hpet0: 3 64-bit timers, 14318180 Hz [ 47.339958] AppArmor: AppArmor Filesystem Enabled [ 47.342831] Time: tsc clocksource has been installed. [ 47.346900] Switched to high resolution mode on CPU 1 [ 47.350812] Switched to high resolution mode on CPU 0 [ 47.355804] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved [ 47.355811] system 00:08: ioport range 0x290-0x297 has been reserved [ 47.355816] system 00:09: ioport range 0x4d0-0x4d1 has been reserved [ 47.355818] system 00:09: ioport range 0x800-0x87f has been reserved [ 47.355820] system 00:09: ioport range 0x480-0x4bf has been reserved [ 47.355823] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 47.355825] system 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved [ 47.355830] system 00:0c: iomem range 0xffc00000-0xffefffff has been reserved [ 47.355835] system 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved [ 47.355837] system 00:0d: iomem range 0xfee00000-0xfee00fff could not be reserved [ 47.355843] system 00:11: iomem range 0xf0000000-0xf3ffffff has been reserved [ 47.355848] system 00:12: iomem range 0x0-0x9ffff could not be reserved [ 47.355850] system 00:12: iomem range 0xc0000-0xcffff could not be reserved [ 47.355852] system 00:12: iomem range 0xe0000-0xfffff could not be reserved [ 47.355855] system 00:12: iomem range 0x100000-0x7fffffff could not be reserved [ 47.355857] system 00:12: iomem range 0x0-0x0 could not be reserved [ 47.386047] PCI: Bridge: 0000:00:01.0 [ 47.386048] IO window: d000-dfff [ 47.386050] MEM window: fa000000-fe9fffff [ 47.386052] PREFETCH window: e0000000-efffffff [ 47.386054] PCI: Bridge: 0000:00:1c.0 [ 47.386055] IO window: disabled. [ 47.386057] MEM window: disabled. [ 47.386059] PREFETCH window: disabled. [ 47.386062] PCI: Bridge: 0000:00:1c.1 [ 47.386063] IO window: disabled. [ 47.386066] MEM window: fea00000-feafffff [ 47.386068] PREFETCH window: disabled. [ 47.386071] PCI: Bridge: 0000:00:1e.0 [ 47.386072] IO window: e000-efff [ 47.386075] MEM window: feb00000-febfffff [ 47.386077] PREFETCH window: disabled. [ 47.386086] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 47.386089] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 47.386100] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 47.386103] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 47.386114] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17 [ 47.386117] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 47.386124] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 47.386129] NET: Registered protocol family 2 [ 47.423683] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 47.423838] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 47.424083] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 47.424199] TCP: Hash tables configured (established 131072 bind 65536) [ 47.424201] TCP reno registered [ 47.435704] checking if image is initramfs... it is [ 47.835006] Freeing initrd memory: 7667k freed [ 47.835442] audit: initializing netlink socket (disabled) [ 47.835451] audit(1222882418.988:1): initialized [ 47.835583] highmem bounce pool size: 64 pages [ 47.836608] VFS: Disk quotas dquot_6.5.1 [ 47.836648] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 47.836726] io scheduler noop registered [ 47.836727] io scheduler anticipatory registered [ 47.836728] io scheduler deadline registered [ 47.836734] io scheduler cfq registered (default) [ 47.836809] Boot video device is 0000:01:00.0 [ 47.836870] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 47.836889] assign_interrupt_mode Found MSI capability [ 47.836906] Allocate Port Service[0000:00:01.0:pcie00] [ 47.836947] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 47.836974] assign_interrupt_mode Found MSI capability [ 47.836996] Allocate Port Service[0000:00:1c.0:pcie00] [ 47.837015] Allocate Port Service[0000:00:1c.0:pcie02] [ 47.837064] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 47.837091] assign_interrupt_mode Found MSI capability [ 47.837113] Allocate Port Service[0000:00:1c.1:pcie00] [ 47.837129] Allocate Port Service[0000:00:1c.1:pcie02] [ 47.837264] isapnp: Scanning for PnP cards... [ 48.189506] isapnp: No Plug & Play device found [ 48.202775] Real Time Clock Driver v1.12ac [ 48.202887] hpet_resources: 0xfed00000 is busy [ 48.202911] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 48.202999] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 48.203399] 00:10: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 48.203757] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 48.203793] input: Macintosh mouse button emulation as /devices/virtual/input/input0 [ 48.203845] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 48.205831] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 48.205834] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 48.234084] mice: PS/2 mouse device common for all mice [ 48.234161] EISA: Probing bus 0 at eisa.0 [ 48.234185] EISA: Detected 0 cards. [ 48.234188] cpuidle: using governor ladder [ 48.234189] cpuidle: using governor menu [ 48.234235] NET: Registered protocol family 1 [ 48.234251] Using IPI No-Shortcut mode [ 48.234266] registered taskstats version 1 [ 48.234323] Magic number: 12:929:591 [ 48.234329] hash matches device ptyc9 [ 48.234339] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 48.234340] EDD information not available. [ 48.234453] Freeing unused kernel memory: 368k freed [ 48.255428] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 49.351898] fuse init (API version 7.9) [ 49.364721] ACPI: SSDT 7FFB00F0, 01D2 (r1 AMI CPU1PM 1 INTL 20060113) [ 49.364940] ACPI: SSDT 7FFB02D0, 0143 (r1 AMI CPU2PM 1 INTL 20060113) [ 49.365073] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 49.365079] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 49.511888] usbcore: registered new interface driver usbfs [ 49.511900] usbcore: registered new interface driver hub [ 49.512080] usbcore: registered new device driver usb [ 49.512844] USB Universal Host Controller Interface driver v3.0 [ 49.512876] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 18 [ 49.512882] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 49.512885] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 49.512995] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 49.513015] uhci_hcd 0000:00:1d.0: irq 18, io base 0x0000c480 [ 49.513078] usb usb1: configuration #1 chosen from 1 choice [ 49.513090] hub 1-0:1.0: USB hub found [ 49.513093] hub 1-0:1.0: 2 ports detected [ 49.590034] SCSI subsystem initialized [ 49.600973] libata version 3.00 loaded. [ 49.615307] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 [ 49.615314] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 49.615317] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 49.615331] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 49.615351] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c800 [ 49.615413] usb usb2: configuration #1 chosen from 1 choice [ 49.615425] hub 2-0:1.0: USB hub found [ 49.615428] hub 2-0:1.0: 2 ports detected [ 49.658210] Floppy drive(s): fd0 is 1.44M [ 49.677752] FDC 0 is a post-1991 82077 [ 49.719096] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 20 [ 49.719102] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 49.719104] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 49.719116] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 49.719136] uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000c880 [ 49.719195] usb usb3: configuration #1 chosen from 1 choice [ 49.719208] hub 3-0:1.0: USB hub found [ 49.719210] hub 3-0:1.0: 2 ports detected [ 49.822869] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16 [ 49.822874] PCI: Setting latency timer of device 0000:00:1d.3 to 64 [ 49.822876] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 49.822888] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 49.822908] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000cc00 [ 49.822964] usb usb4: configuration #1 chosen from 1 choice [ 49.822976] hub 4-0:1.0: USB hub found [ 49.822978] hub 4-0:1.0: 2 ports detected [ 49.925761] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 18 [ 49.925769] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 49.925772] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 49.925788] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 [ 49.929674] ehci_hcd 0000:00:1d.7: debug port 1 [ 49.929678] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 49.929681] ehci_hcd 0000:00:1d.7: irq 18, io mem 0xf9ffbc00 [ 49.958564] usb 2-2: new full speed USB device using uhci_hcd and address 2 [ 49.973533] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 49.973617] usb usb5: configuration #1 chosen from 1 choice [ 49.973637] hub 5-0:1.0: USB hub found [ 49.973641] hub 5-0:1.0: 8 ports detected [ 50.074115] ACPI: PCI Interrupt 0000:04:01.2[B] -> GSI 17 (level, low) -> IRQ 17 [ 50.123699] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[febff800-febfffff] Max Packet=[2048] IR/IT contexts=[4/8] [ 50.124257] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 20 [ 50.124279] PCI: Setting latency timer of device 0000:00:1f.1 to 64 [ 50.124286] ACPI: PCI interrupt for device 0000:00:1f.1 disabled [ 50.124299] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 [ 50.124311] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 50.124316] ACPI: PCI interrupt for device 0000:00:1f.2 disabled [ 50.126039] ata_piix 0000:00:1f.1: version 2.12 [ 50.126046] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 20 [ 50.126059] PCI: Setting latency timer of device 0000:00:1f.1 to 64 [ 50.126342] scsi0 : ata_piix [ 50.126658] scsi1 : ata_piix [ 50.128779] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 [ 50.128781] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 [ 50.424627] usb 5-4: new high speed USB device using ehci_hcd and address 2 [ 50.456943] ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-4167B, DL10, max UDMA/33 [ 50.457162] ata1.01: ATA-6: ST380020A, 3.39, max UDMA/100 [ 50.457165] ata1.01: 156301488 sectors, multi 16: LBA [ 50.486929] irq 19: nobody cared (try booting with the "irqpoll" option) [ 50.486933] Pid: 0, comm: swapper Not tainted 2.6.24-19-generic #1 [ 50.486936] [<c01691b4>] __report_bad_irq+0x24/0x80 [ 50.486944] [<c016948b>] note_interrupt+0x27b/0x2c0 [ 50.486947] [<f88a3bab>] usb_hcd_irq+0x2b/0x60 [usbcore] [ 50.486963] [<c01686b0>] handle_IRQ_event+0x30/0x60 [ 50.486966] [<c0169e46>] handle_fasteoi_irq+0x86/0xe0 [ 50.486969] [<c0106f1b>] do_IRQ+0x3b/0x70 [ 50.486972] [<c0144317>] hrtimer_start+0xc7/0x140 [ 50.486977] [<c0105413>] common_interrupt+0x23/0x30 [ 50.486980] [<c01022e6>] mwait_idle_with_hints+0x46/0x60 [ 50.486983] [<c0102695>] cpu_idle+0x45/0xd0 [ 50.486987] ======================= [ 50.486988] handlers: [ 50.486989] [<f88a3b80>] (usb_hcd_irq+0x0/0x60 [usbcore]) [ 50.487002] Disabling IRQ #19 [ 50.557695] usb 5-4: configuration #1 chosen from 1 choice [ 50.628453] ata1.00: configured for UDMA/33 [ 50.644618] ata1.01: configured for UDMA/100 [ 50.795875] usb 5-7: new high speed USB device using ehci_hcd and address 3 [ 50.815061] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-4167B DL10 PQ: 0 ANSI: 5 [ 50.815155] scsi 0:0:1:0: Direct-Access ATA ST380020A 3.39 PQ: 0 ANSI: 5 [ 50.815198] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 50.815214] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 [ 50.815230] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 50.815257] scsi2 : ata_piix [ 50.815279] scsi3 : ata_piix [ 50.816092] ata3: SATA max UDMA/133 cmd 0xc400 ctl 0xc080 bmdma 0xb880 irq 19 [ 50.816093] ata4: SATA max UDMA/133 cmd 0xc000 ctl 0xbc00 bmdma 0xb888 irq 19 [ 51.017300] usb 5-7: configuration #1 chosen from 1 choice [ 51.018788] usbcore: registered new interface driver libusual [ 51.021456] Initializing USB Mass Storage driver... [ 51.021804] scsi4 : SCSI emulation for USB Mass Storage devices [ 51.022111] usb-storage: device found at 2 [ 51.022112] usb-storage: waiting for device to settle before scanning [ 51.022127] scsi5 : SCSI emulation for USB Mass Storage devices [ 51.022198] usb-storage: device found at 3 [ 51.022199] usb-storage: waiting for device to settle before scanning [ 51.022202] usbcore: registered new interface driver usb-storage [ 51.022203] USB Mass Storage support registered. [ 51.390746] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c015102d50e] [ 56.009531] usb-storage: device scan complete [ 56.009556] usb-storage: device scan complete [ 56.009916] scsi 4:0:0:0: Direct-Access TrekStor HDT725032VLAT80 1.05 PQ: 0 ANSI: 0 [ 56.012948] Driver 'sd' needs updating - please use bus_type methods [ 56.012978] sd 0:0:1:0: [sda] 156301488 512-byte hardware sectors (80026 MB) [ 56.012985] sd 0:0:1:0: [sda] Write Protect is off [ 56.012986] sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00 [ 56.012994] sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 56.013017] sd 0:0:1:0: [sda] 156301488 512-byte hardware sectors (80026 MB) [ 56.013023] sd 0:0:1:0: [sda] Write Protect is off [ 56.013024] sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00 [ 56.013032] sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 56.013034] sda: sda1 sda2 <<5>scsi 5:0:0:0: Direct-Access Generic 2.0 Reader -0 1.00 PQ: 0 ANSI: 0 CCS [ 56.054544] sda5 sda6 > [ 56.068517] sd 0:0:1:0: [sda] Attached SCSI disk [ 56.069408] sd 4:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 56.069920] scsi 5:0:0:1: Direct-Access Generic 2.0 Reader -1 1.00 PQ: 0 ANSI: 0 CCS [ 56.070280] sd 4:0:0:0: [sdb] Write Protect is off [ 56.070283] sd 4:0:0:0: [sdb] Mode Sense: 23 00 00 00 [ 56.070284] sd 4:0:0:0: [sdb] Assuming drive cache: write through [ 56.071278] sd 4:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 56.072276] sd 4:0:0:0: [sdb] Write Protect is off [ 56.072278] sd 4:0:0:0: [sdb] Mode Sense: 23 00 00 00 [ 56.072279] sd 4:0:0:0: [sdb] Assuming drive cache: write through [ 56.072282] sdb: sdb1 sdb3 < sdb5<5>scsi 5:0:0:2: Direct-Access Generic 2.0 Reader -2 1.00 PQ: 0 ANSI: 0 CCS [ 56.108457] sdb6 > [ 56.108525] sd 4:0:0:0: [sdb] Attached SCSI disk [ 56.109483] sd 5:0:0:0: [sdc] Attached SCSI removable disk [ 56.110479] sd 5:0:0:1: [sdd] Attached SCSI removable disk [ 56.111476] sd 5:0:0:2: [sde] Attached SCSI removable disk [ 56.114099] scsi 0:0:0:0: Attached scsi generic sg0 type 5 [ 56.114108] sd 0:0:1:0: Attached scsi generic sg1 type 0 [ 56.114117] sd 4:0:0:0: Attached scsi generic sg2 type 0 [ 56.114126] sd 5:0:0:0: Attached scsi generic sg3 type 0 [ 56.114135] sd 5:0:0:1: Attached scsi generic sg4 type 0 [ 56.114145] sd 5:0:0:2: Attached scsi generic sg5 type 0 [ 63.100048] end_request: I/O error, dev fd0, sector 0 [ 75.243179] end_request: I/O error, dev fd0, sector 0 [ 75.243181] Buffer I/O error on device fd0, logical block 0 [ 80.919182] ata3.00: qc timeout (cmd 0x27) [ 80.919186] ata3.00: failed to read native max address (err_mask=0x4) [ 80.919190] ata3: failed to recover some devices, retrying in 5 secs [ 87.383116] end_request: I/O error, dev fd0, sector 0 [ 87.383118] Buffer I/O error on device fd0, logical block 0 [ 100.536300] end_request: I/O error, dev fd0, sector 0 [ 112.684467] end_request: I/O error, dev fd0, sector 0 [ 112.684468] Buffer I/O error on device fd0, logical block 0 [ 116.016452] ata3.00: qc timeout (cmd 0x27) [ 116.016456] ata3.00: failed to read native max address (err_mask=0x4) [ 116.016458] ata3.00: revalidation failed (errno=-5) [ 116.016460] ata3: failed to recover some devices, retrying in 5 secs [ 124.827498] end_request: I/O error, dev fd0, sector 0 [ 124.827501] Buffer I/O error on device fd0, logical block 0 [ 125.256697] kjournald starting. Commit interval 5 seconds [ 125.256701] EXT3-fs: mounted filesystem with ordered data mode. [ 125.286265] kjournald starting. Commit interval 5 seconds [ 125.286269] EXT3-fs: mounted filesystem with ordered data mode. [ 138.488108] end_request: I/O error, dev fd0, sector 0 [ 150.635629] end_request: I/O error, dev fd0, sector 0 [ 150.635632] Buffer I/O error on device fd0, logical block 0 [ 151.113729] ata3.00: qc timeout (cmd 0x27) [ 151.113734] ata3.00: failed to read native max address (err_mask=0x4) [ 151.113736] ata3.00: revalidation failed (errno=-5) [ 151.113739] ata3.00: disabled [ 151.616705] ata3: soft resetting link [ 151.772422] ata3: EH complete [ 151.942683] Driver 'sr' needs updating - please use bus_type methods [ 151.946830] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray [ 151.946831] Uniform CD-ROM driver Revision: 3.20 [ 151.946854] sr 0:0:0:0: Attached scsi CD-ROM sr0 [ 162.790561] end_request: I/O error, dev fd0, sector 0 [ 162.790565] Buffer I/O error on device fd0, logical block 0 [ 163.309957] kjournald starting. Commit interval 5 seconds [ 163.309962] EXT3-fs: mounted filesystem with ordered data mode. [ 163.774575] kjournald starting. Commit interval 5 seconds [ 163.774580] EXT3-fs: mounted filesystem with ordered data mode. [ 163.795906] kjournald starting. Commit interval 5 seconds [ 163.795910] EXT3-fs: mounted filesystem with ordered data mode. [ 176.993936] end_request: I/O error, dev fd0, sector 0 [ 189.141474] end_request: I/O error, dev fd0, sector 0 [ 189.141477] Buffer I/O error on device fd0, logical block 0 [ 201.285560] end_request: I/O error, dev fd0, sector 0 [ 201.285562] Buffer I/O error on device fd0, logical block 0 [ 201.794176] kjournald starting. Commit interval 5 seconds [ 201.794180] EXT3-fs: mounted filesystem with ordered data mode. [ 202.217720] kjournald starting. Commit interval 5 seconds [ 202.217725] EXT3-fs: mounted filesystem with ordered data mode. [ 202.239052] kjournald starting. Commit interval 5 seconds [ 202.239056] EXT3-fs: mounted filesystem with ordered data mode. [ 204.801108] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 204.853620] ISO 9660 Extensions: RRIP_1991A [ 205.287757] Registering unionfs 1.4 [ 205.287758] unionfs: debugging is not enabled [ 205.291943] loop: module loaded [ 205.527502] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 265.006007] input: PC Speaker as /devices/platform/pcspkr/input/input2 [ 265.857008] Linux agpgart interface v0.102 [ 266.114186] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 266.526557] input: Power Button (FF) as /devices/virtual/input/input3 [ 266.566061] ACPI: Power Button (FF) [PWRF] [ 266.566128] input: Power Button (CM) as /devices/virtual/input/input4 [ 266.608977] ACPI: Power Button (CM) [PWRB] [ 266.807243] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 266.989222] iTCO_vendor_support: vendor-support=0 [ 267.038653] parport_pc 00:07: reported by Plug and Play ACPI [ 267.038749] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] [ 267.275810] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007) [ 267.275856] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860) [ 267.275878] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 267.460392] gameport: EMU10K1 is pci0000:04:01.1/gameport0, io 0xec00, speed 1084kHz [ 267.697793] intel_rng: FWH not detected [ 267.984710] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17 [ 267.984718] PCI: Setting latency timer of device 0000:02:00.0 to 64 [ 267.984724] atl1 0000:02:00.0: version 2.0.7 [ 267.997842] input: ImExPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input5 [ 268.970212] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 268.970224] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 269.005954] hda_codec: Unknown model for ALC662, trying auto-probe from BIOS... [ 269.037328] ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 269.040732] ALSA /build/buildd/linux-ubuntu-modules-2.6.24-2.6.24/debian/build/build-generic/sound/alsa-driver/pci/emu10k1/../../alsa-kernel/pci/emu10k1/emufx.c:1544: Installing spdif_bug patch: Audigy 2 ZS [SB0350] [ 270.847689] ip_tables: (C) 2000-2006 Netfilter Core Team [ 271.858586] No dock devices found. [ 278.458540] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 278.458543] apm: disabled - APM is not SMP safe. [ 278.603234] lp0: using parport0 (interrupt-driven). [ 278.677028] ppdev: user-space parallel port driver [ 286.614107] atl1 0000:02:00.0: eth0 link is up 100 Mbps full duplex [ 286.958557] Bluetooth: Core ver 2.11 [ 286.958799] NET: Registered protocol family 31 [ 286.958802] Bluetooth: HCI device and connection manager initialized [ 286.958804] Bluetooth: HCI socket layer initialized [ 287.034748] Bluetooth: L2CAP ver 2.9 [ 287.034751] Bluetooth: L2CAP socket layer initialized [ 287.376556] Bluetooth: RFCOMM socket layer initialized [ 287.376564] Bluetooth: RFCOMM TTY layer initialized [ 287.376565] Bluetooth: RFCOMM ver 1.8 [ 291.310773] NET: Registered protocol family 17 [ 295.970649] NET: Registered protocol family 10 [ 295.970838] lo: Disabled Privacy Extensions [ 306.437692] eth0: no IPv6 routers present [ 353.978224] kjournald starting. Commit interval 5 seconds [ 353.978227] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended [ 353.978711] EXT3 FS on sdb5, internal journal [ 353.978715] EXT3-fs: mounted filesystem with ordered data mode. [ 354.473135] kjournald starting. Commit interval 5 seconds [ 354.473746] EXT3 FS on sdb6, internal journal [ 354.473751] EXT3-fs: mounted filesystem with ordered data mode. [ 493.870761] kjournald starting. Commit interval 5 seconds [ 493.876283] EXT3 FS on sda6, internal journal [ 493.876287] EXT3-fs: mounted filesystem with ordered data mode. [ 3146.435123] end_request: I/O error, dev fd0, sector 0 [ 3158.585783] end_request: I/O error, dev fd0, sector 0 [ 3158.619330] program gparted is using a deprecated SCSI ioctl, please convert it to SG_IO [ 3170.778194] end_request: I/O error, dev fd0, sector 0 [ 3182.933819] end_request: I/O error, dev fd0, sector 0 [ 3195.072113] end_request: I/O error, dev fd0, sector 0 [ 3195.072117] Buffer I/O error on device fd0, logical block 0 [ 3207.232483] end_request: I/O error, dev fd0, sector 0 [ 3207.232487] Buffer I/O error on device fd0, logical block 0 ubuntu@ubuntu:~$
Mir sagen diese Angaben leider nicht viel. So hoffe ich auf Empfehlungen zur weiteren Vorgehensweise. Die gefundenen Beiträge zu diesem Thema waren sehr differenziert und ich vermag nicht mit Sicherheit zu beurteilen welche der angegebenen Konstellationen in meinem Fall weiterhelfen würde. Vorab ein herzliches Dankeschön.