Seit heute friert mein Notebook immer wieder ein, das Problem ist leider nicht direkt ersichtlich.
Der kurze RAM-Test von HP findet keine Fehler und in den Logs konnte ich auch auf Anhieb nichts erkennen.
Die Ausgabe des Smart-Tests ist etwas seltsam mit der Warnung:
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-151-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: CT500MX500SSD1 Serial Number: *** LU WWN Device Id: *** Firmware Version: M3CR020 User Capacity: 500.107.862.016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA >3.2 (0x1ff), 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jul 23 18:38:50 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 100 100 000 Pre-fail Always - 0 5 Reallocated_Sector_Ct 0x0032 100 100 010 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 10684 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2951 171 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 172 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 173 Unknown_Attribute 0x0032 095 095 000 Old_age Always - 86 174 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 22 180 Unused_Rsvd_Blk_Cnt_Tot 0x0033 000 000 000 Pre-fail Always - 44 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 000 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 194 Temperature_Celsius 0x0022 060 045 000 Old_age Always - 40 (Min/Max 0/55) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 100 100 000 Old_age Always - 0 202 Unknown_SSD_Attribute 0x0030 095 095 001 Old_age Offline - 5 206 Unknown_SSD_Attribute 0x000e 100 100 000 Old_age Always - 0 210 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 246 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 12678524907 247 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 220764242 248 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 904399969 SMART Error Log Version: 1 Warning: ATA error count 0 inconsistent with error log pointer 2 ATA Error Count: 0 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error -1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 ec 00 00 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ec 00 00 00 00 00 00 00 00:00:00.000 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00:00:00.000 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00:00:00.000 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00:00:00.000 IDENTIFY DEVICE c8 00 00 00 00 00 00 00 00:00:00.000 READ DMA SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 10683 - # 2 Short offline Completed without error 00% 10682 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
Jetzt lasse ich Memtest laufen, aber wenn der auch nichts findet (danach sieht es aktuell aus), weiß ich nicht weiter. Das System war immer sehr Stabil, es gab nie Probleme. Es wurde auch nichts neues installiert, außer vielleicht Ubuntu Updates.
Also heute schon mindestens 4x ... es ist anscheinend ein erstes Problem. https://wiki.ubuntuusers.de/Notfall/#System-friert-ein
* umschalten auf TTY Terminal hat nicht funktioniert
* Magic SysRQ hat meistens noch funktioniert
* Magic SysRQ Alt + Druck +c hatte ich gedrückt, konnte aber keinen KernelDump finden
* es sieht so aus als ob die Logdateien nicht mehr geschrieben werden
Es ist mein Hauptrechner, deswegen bekomme ich hier gerade etwas Panik. Ich würde mich über jede Hilfe freuen.