Hallo Zusammen,
meim Lappie macht mal wieder Probleme beim Booten und das ist nun vermutlich die letzte Aktion, die ich starte. Danach muss dringend eine neue Kiste her, aber man lernt ja nur dazu 😕
Gehe ich zuerst in den Recovery - Modus und boote dann, dann fährt das System problemlos hoch. Es scheinen aber nicht alle Graphiktreiber geladen zu sein. Zuerst hing der Bootvorgang bei der Zeile "Adding 9428k swap on /dev/sda5. Priority:-1 extents:1 Daraufhin habe ich die Swappartition neu angelegt:
1 2 3 | sudo swapoff /dev/sda5 sudo mkswap /dev/sda5 sudo update-initramfs -u |
Danach hat es einmal funktioniert zu booten, und dann hat es sich wieder aufgehängt. Diesmal bei der Stelle: random: nonblocking pool is initialized
Ich weiß nicht, ob es damit zu tun haben könnte, aber ich habe heute einige USB Geräte um- bzw. abgesteckt. Momentan hängt nur eine Maus und ein USB Hub dran. Beim ersten Einschalten, hat allerdings alles tadellos funktioniert.
Hier der Inhalt von /var/log/boot.log (Nachdem ich über den Recovery-Modus gebootet habe)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 | Stopping load modules from /etc/modules^[[74G[ OK ]^M * Stopping cold plug devices^[[74G[ OK ]^M * Stopping log initial device creation^[[74G[ OK ]^M * Starting set console font^[[74G[ OK ]^M * Stopping set console font^[[74G[ OK ]^M * Starting userspace bootsplash^[[74G[ OK ]^M * Starting Send an event to indicate plymouth is up^[[74G[ OK ]^M * Stopping userspace bootsplash^[[74G[ OK ]^M * Stopping Read required files in advance^[[74G[ OK ]^M * Starting Mount filesystems on boot^[[74G[ OK ]^M * Stopping Track if upstart is running in a container^[[74G[ OK ]^M * Starting set console keymap^[[74G[ OK ]^M * Starting Signal sysvinit that virtual filesystems are mounted^[[74G[ OK ]^M * Starting Signal sysvinit that virtual filesystems are mounted^[[74G[ OK ]^M * Stopping set console keymap^[[74G[ OK ]^M * Starting Signal sysvinit that remote filesystems are mounted^[[74G[ OK ]^M * Starting Signal sysvinit that the rootfs is mounted^[[74G[ OK ]^M * Starting Clean /tmp directory^[[74G[ OK ]^M * Stopping Clean /tmp directory^[[74G[ OK ]^M * Stopping Read required files in advance (for other mountpoints)^[[74G[ OK ]^M * Starting Signal sysvinit that local filesystems are mounted^[[74G[ OK ]^M * Starting restore software rfkill state^[[74G[ OK ]^M * Starting configure network device security^[[74G[ OK ]^M * Stopping restore software rfkill state^[[74G[ OK ]^M * Starting Flush boot log to disk^[[74G[ OK ]^M * Starting flush early job output to logs^[[74G[ OK ]^M * Starting save udev log and update rules^[[74G[ OK ]^M * Stopping Failsafe Boot Delay^[[74G[ OK ]^M * Starting System V initialisation compatibility^[[74G[ OK ]^M * Stopping Flush boot log to disk^[[74G[ OK ]^M * Stopping flush early job output to logs^[[74G[ OK ]^M * Stopping save udev log and update rules^[[74G[ OK ]^M * Starting configure virtual network devices^[[74G[ OK ]^M * Starting Bridge file events into upstart^[[74G[ OK ]^M * Starting system logging daemon^[[74G[ OK ]^M Skipping profile in /etc/apparmor.d/disable: usr.bin.firefox^M Skipping profile in /etc/apparmor.d/disable: usr.sbin.rsyslogd^M * Starting AppArmor profiles ^[[80G ^M^[[74G[ OK ]^M * Starting D-Bus system message bus^[[74G[ OK ]^M * Setting sensors limits ^[[80G ^M^[[74G[ OK ]^M * Starting modem connection manager^[[74G[ OK ]^M * Starting configure network device security^[[74G[ OK ]^M * Starting SystemD login management service^[[74G[ OK ]^M * Starting mDNS/DNS-SD daemon^[[74G[ OK ]^M * Starting Reload cups, upon starting avahi-daemon to make sure remote queues are populated^[[74G[ OK ]^M * Stopping Reload cups, upon starting avahi-daemon to make sure remote queues are populated^[[74G[ OK ]^M * Starting bluetooth daemon^[[74G[ OK ]^M * Setting up X socket directories... ^[[80G ^M^[[74G[ OK ]^M * Stopping System V initialisation compatibility^[[74G[ OK ]^M * Starting System V runlevel compatibility^[[74G[ OK ]^M * Starting anac(h)ronistic cron^[[74G[ OK ]^M * Starting save kernel messages^[[74G[ OK ]^M * Starting ACPI daemon^[[74G[ OK ]^M * Starting regular background program processing daemon^[[74G[ OK ]^M * Starting CPU interrupts balancing daemon^[[74G[ OK ]^M * Starting network connection manager^[[74G[ OK ]^M * Stopping save kernel messages^[[74G[ OK ]^M * Stopping anac(h)ronistic cron^[[74G[ OK ]^M * speech-dispatcher disabled; edit /etc/default/speech-dispatcher^M saned disabled; edit /etc/default/saned^M * Restoring resolver state... ^[[80G ^M^[[74G[ OK ]^M * Starting cups-browsed - Bonjour remote printer browsing daemon^[[74G[ OK ]^M * Stopping Restore Sound Card State^[[74G[ OK ]^M * Starting automatic crash report generation^[[74G[ OK ]^M * Stopping System V runlevel compatibility^[[74G[ OK ]^M * Starting crash report submission daemon^[[74G[ OK ]^M |
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 | :/var/log$ dmesg [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.13.0-68-generic (buildd@lgw01-47) (gcc version 4.8.2 (Ubuntu 4.8.2-19ubuntu1) ) #111-Ubuntu SMP Fri Nov 6 18:18:09 UTC 2015 (Ubuntu 3.13.0-68.111-generic 3.13.11-ckt27) [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] NSC Geode by NSC [ 0.000000] Cyrix CyrixInstead [ 0.000000] Centaur CentaurHauls [ 0.000000] Transmeta GenuineTMx86 [ 0.000000] Transmeta TransmetaCPU [ 0.000000] UMC UMC UMC UMC [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009dbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009dc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000dc000-0x00000000000dffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000037e8ffff] usable [ 0.000000] BIOS-e820: [mem 0x0000000037e90000-0x0000000037ea1fff] ACPI data [ 0.000000] BIOS-e820: [mem 0x0000000037ea2000-0x0000000037efffff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x0000000037f00000-0x0000000037ffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec0ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.4 present. [ 0.000000] DMI: SAMSUNG ELECTRONICS CO., LTD. R40/R41/R40/R41, BIOS 23YA 04/17/2007 [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] e820: last_pfn = 0x37e90 max_arch_pfn = 0x1000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-CFFFF write-protect [ 0.000000] D0000-DFFFF uncachable [ 0.000000] E0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask FE0000000 write-back [ 0.000000] 1 base 020000000 mask FF0000000 write-back [ 0.000000] 2 base 030000000 mask FF8000000 write-back [ 0.000000] 3 base 037F00000 mask FFFF00000 uncachable [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] original variable MTRRs [ 0.000000] reg 0, base: 0GB, range: 512MB, type WB [ 0.000000] reg 1, base: 512MB, range: 256MB, type WB [ 0.000000] reg 2, base: 768MB, range: 128MB, type WB [ 0.000000] reg 3, base: 895MB, range: 1MB, type UC [ 0.000000] total RAM covered: 895M [ 0.000000] Found optimal setting for mtrr clean up [ 0.000000] gran_size: 64K chunk_size: 256M num_reg: 3 lose cover RAM: 0G [ 0.000000] New variable MTRRs [ 0.000000] reg 0, base: 0GB, range: 1GB, type WB [ 0.000000] reg 1, base: 895MB, range: 1MB, type UC [ 0.000000] reg 2, base: 896MB, range: 128MB, type UC [ 0.000000] found SMP MP-table at [mem 0x000f7530-0x000f753f] mapped at [c00f7530] [ 0.000000] Scanning 1 areas for low memory corruption [ 0.000000] initial memory mapped: [mem 0x00000000-0x01ffffff] [ 0.000000] Base memory trampoline at [c0099000] 99000 size 16384 [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff] [ 0.000000] [mem 0x00000000-0x000fffff] page 4k [ 0.000000] init_memory_mapping: [mem 0x37800000-0x379fffff] [ 0.000000] [mem 0x37800000-0x379fffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x34000000-0x377fffff] [ 0.000000] [mem 0x34000000-0x377fffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x00100000-0x33ffffff] [ 0.000000] [mem 0x00100000-0x001fffff] page 4k [ 0.000000] [mem 0x00200000-0x33ffffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x37a00000-0x37bfdfff] [ 0.000000] [mem 0x37a00000-0x37bfdfff] page 4k [ 0.000000] BRK [0x01b9d000, 0x01b9dfff] PGTABLE [ 0.000000] RAMDISK: [mem 0x35c1a000-0x36e04fff] [ 0.000000] ACPI: RSDP 000f7500 000014 (v00 PTLTD ) [ 0.000000] ACPI: RSDT 37e9c606 000040 (v01 SECCSD LH43STAR 06040000 LTP 00000000) [ 0.000000] ACPI: FACP 37ea1d7c 000074 (v01 SEC FIRENZE2 06040000 SEC 000F4240) [ 0.000000] ACPI: DSDT 37e9d97e 0043FE (v01 ATI SB450 06040000 INTL 20050228) [ 0.000000] ACPI: FACS 37ea2fc0 000040 [ 0.000000] ACPI: APIC 37ea1df0 00005E (v01 PTLTD ? APIC 06040000 LTP 00000000) [ 0.000000] ACPI: MCFG 37ea1e4e 00003C (v01 PTLTD MCFG 06040000 LTP 00000000) [ 0.000000] ACPI: SLIC 37ea1e8a 000176 (v01 SECCSD LH43STAR 06040000 LTP 00000000) [ 0.000000] ACPI: SSDT 37e9cc5f 00025F (v01 PmRef Cpu0Tst 00003000 INTL 20050228) [ 0.000000] ACPI: SSDT 37e9cbb9 0000A6 (v01 PmRef Cpu1Tst 00003000 INTL 20050228) [ 0.000000] ACPI: SSDT 37e9c646 000573 (v01 PmRef CpuPm 00003000 INTL 20050228) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] 2MB HIGHMEM available. [ 0.000000] 891MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 37bfe000 [ 0.000000] low ram: 0 - 37bfe000 [ 0.000000] BRK [0x01b9e000, 0x01b9efff] PGTABLE [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00001000-0x00ffffff] [ 0.000000] Normal [mem 0x01000000-0x37bfdfff] [ 0.000000] HighMem [mem 0x37bfe000-0x37e8ffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00001000-0x0009cfff] [ 0.000000] node 0: [mem 0x00100000-0x37e8ffff] [ 0.000000] On node 0 totalpages: 228908 [ 0.000000] free_area_init_node: node 0, pgdat c19a3780, node_mem_map f74fe020 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3996 pages, LIFO batch:0 [ 0.000000] Normal zone: 1752 pages used for memmap [ 0.000000] Normal zone: 224254 pages, LIFO batch:31 [ 0.000000] HighMem zone: 6 pages used for memmap [ 0.000000] HighMem zone: 658 pages, LIFO batch:0 [ 0.000000] Using APIC driver default [ 0.000000] SB4X0 revision 0x83 [ 0.000000] Ignoring ACPI timer override. [ 0.000000] If you got timer trouble try acpi_use_timer_override [ 0.000000] ACPI: PM-Timer IO Port: 0x8008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dbfff] [ 0.000000] PM: Registered nosave memory: [mem 0x000dc000-0x000dffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000e3fff] [ 0.000000] PM: Registered nosave memory: [mem 0x000e4000-0x000fffff] [ 0.000000] e820: [mem 0x38000000-0xdfffffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 14 pages/cpu @f74dc000 s35520 r0 d21824 u57344 [ 0.000000] pcpu-alloc: s35520 r0 d21824 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227124 [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-68-generic root=UUID=a0b6bd4e-9c0e-4cfa-864b-c1e35e70e8ba ro recovery nomodeset [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Initializing CPU#0 [ 0.000000] allocated 1832056 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Initializing HighMem for node 0 (00037bfe:00037e90) [ 0.000000] Memory: 875416K/915632K available (6559K kernel code, 645K rwdata, 2772K rodata, 880K init, 924K bss, 40216K reserved, 2632K highmem) [ 0.000000] virtual kernel memory layout: [ 0.000000] fixmap : 0xfff14000 - 0xfffff000 ( 940 kB) [ 0.000000] pkmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xf83fe000 - 0xffbfe000 ( 120 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf7bfe000 ( 891 MB) [ 0.000000] .init : 0xc19c1000 - 0xc1a9d000 ( 880 kB) [ 0.000000] .data : 0xc16681c0 - 0xc19c0640 (3425 kB) [ 0.000000] .text : 0xc1000000 - 0xc16681c0 (6560 kB) [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] NR_IRQS:2304 nr_irqs:512 16 [ 0.000000] CPU 0 irqstacks, hard=f5808000 soft=f580a000 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] tsc: Detected 1666.734 MHz processor [ 0.004004] Calibrating delay loop (skipped), value calculated using timer frequency.. 3333.46 BogoMIPS (lpj=6666936) [ 0.004099] pid_max: default: 32768 minimum: 301 [ 0.004204] Security Framework initialized [ 0.004305] AppArmor: AppArmor initialized [ 0.004354] Yama: becoming mindful. [ 0.004501] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.004553] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.005113] Initializing cgroup subsys memory [ 0.005181] Initializing cgroup subsys devices [ 0.005229] Initializing cgroup subsys freezer [ 0.005278] Initializing cgroup subsys blkio [ 0.005326] Initializing cgroup subsys perf_event [ 0.005374] Initializing cgroup subsys hugetlb [ 0.005474] CPU: Physical Processor ID: 0 [ 0.005523] CPU: Processor Core ID: 0 [ 0.005572] mce: CPU supports 6 MCE banks [ 0.005631] CPU0: Thermal monitoring enabled (TM2) [ 0.005681] process: using mwait in idle threads [ 0.005755] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4 [ 0.005755] Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32 [ 0.005755] tlb_flushall_shift: -1 [ 0.006321] Freeing SMP alternatives memory: 32K (c1a9d000 - c1aa5000) [ 0.008678] ACPI: Core revision 20131115 [ 0.012532] ACPI: All ACPI Tables successfully acquired [ 0.016010] ftrace: allocating 27884 entries in 55 pages [ 0.028238] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.028750] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1 [ 0.069813] smpboot: CPU0: Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz (fam: 06, model: 0f, stepping: 06) [ 0.072000] Performance Events: PEBS fmt0-, 4-deep LBR, Core2 events, Intel PMU driver. [ 0.072000] perf_event_intel: PEBS disabled due to CPU errata [ 0.072000] ... version: 2 [ 0.072000] ... bit width: 40 [ 0.072000] ... generic registers: 2 [ 0.072000] ... value mask: 000000ffffffffff [ 0.072000] ... max period: 000000007fffffff [ 0.072000] ... fixed-purpose events: 3 [ 0.072000] ... event mask: 0000000700000003 [ 0.072000] CPU 1 irqstacks, hard=f58ec000 soft=f58ee000 [ 0.072000] x86: Booting SMP configuration: [ 0.008000] Initializing CPU#1 [ 0.072000] .... node #0, CPUs: #1 [ 0.084074] x86: Booted up 1 node, 2 CPUs [ 0.084213] smpboot: Total of 2 processors activated (6666.93 BogoMIPS) [ 0.084384] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter. [ 0.086239] devtmpfs: initialized [ 0.086239] EVM: security.selinux [ 0.086239] EVM: security.SMACK64 [ 0.086239] EVM: security.ima [ 0.086239] EVM: security.capability [ 0.088106] PM: Registering ACPI NVS region [mem 0x37ea2000-0x37efffff] (385024 bytes) [ 0.088852] pinctrl core: initialized pinctrl subsystem [ 0.089018] regulator-dummy: no parameters [ 0.089110] RTC time: 0:49:38, date: 11/29/15 [ 0.089218] NET: Registered protocol family 16 [ 0.089510] EISA bus registered [ 0.089559] cpuidle: using governor ladder [ 0.089605] cpuidle: using governor menu [ 0.089763] ACPI: bus type PCI registered [ 0.089814] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.089969] PCI: MMCONFIG for domain 0000 [bus 00-04] at [mem 0xe0000000-0xe04fffff] (base 0xe0000000) [ 0.090024] PCI: MMCONFIG at [mem 0xe0000000-0xe04fffff] reserved in E820 [ 0.090071] PCI: Using MMCONFIG for extended config space [ 0.090118] PCI: Using configuration type 1 for base access [ 0.092113] bio: create slab <bio-0> at 0 [ 0.092151] ACPI: Added _OSI(Module Device) [ 0.092201] ACPI: Added _OSI(Processor Device) [ 0.092247] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.092293] ACPI: Added _OSI(Processor Aggregator Device) [ 0.096458] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 0.099147] ACPI: SSDT 37e9d630 0002A4 (v01 PmRef Cpu0Ist 00003000 INTL 20050228) [ 0.099568] ACPI: Dynamic OEM Table Load: [ 0.099692] ACPI: SSDT (null) 0002A4 (v01 PmRef Cpu0Ist 00003000 INTL 20050228) [ 0.100176] ACPI: SSDT 37e9cebe 0006ED (v01 PmRef Cpu0Cst 00003001 INTL 20050228) [ 0.100642] ACPI: Dynamic OEM Table Load: [ 0.100766] ACPI: SSDT (null) 0006ED (v01 PmRef Cpu0Cst 00003001 INTL 20050228) [ 0.101231] ACPI: SSDT 37e9d8d4 0000AA (v01 PmRef Cpu1Ist 00003000 INTL 20050228) [ 0.101650] ACPI: Dynamic OEM Table Load: [ 0.101774] ACPI: SSDT (null) 0000AA (v01 PmRef Cpu1Ist 00003000 INTL 20050228) [ 0.102006] ACPI: SSDT 37e9d5ab 000085 (v01 PmRef Cpu1Cst 00003000 INTL 20050228) [ 0.102410] ACPI: Dynamic OEM Table Load: [ 0.102534] ACPI: SSDT (null) 000085 (v01 PmRef Cpu1Cst 00003000 INTL 20050228) [ 0.104086] ACPI: Interpreter enabled [ 0.104165] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131115/hwxface-580) [ 0.104296] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131115/hwxface-580) [ 0.104440] ACPI: (supports S0 S3 S4 S5) [ 0.104486] ACPI: Using IOAPIC for interrupt routing [ 0.104647] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug [ 0.104848] ACPI: No dock devices found. [ 0.112339] ACPI: Power Resource [FN00] (off) [ 0.112735] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.112735] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI] [ 0.112735] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM [ 0.113359] acpi PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored) [ 0.113364] acpi PNP0A03:00: host bridge window [mem 0x000d0000-0x000d3fff] (ignored) [ 0.113368] acpi PNP0A03:00: host bridge window [mem 0x000d4000-0x000d7fff] (ignored) [ 0.113372] acpi PNP0A03:00: host bridge window [mem 0x000d8000-0x000dbfff] (ignored) [ 0.113375] acpi PNP0A03:00: host bridge window [mem 0x38000000-0xfebfffff] (ignored) [ 0.113379] acpi PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored) [ 0.113382] acpi PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored) [ 0.113386] PCI: root bus 00: using default resources [ 0.113391] acpi PNP0A03:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-04] only partially covers this bridge [ 0.113612] PCI host bridge to bus 0000:00 [ 0.113661] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.113709] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.113756] pci_bus 0000:00: root bus resource [mem 0x00000000-0xfffffffff] [ 0.113814] pci 0000:00:00.0: [1002:5a31] type 00 class 0x060000 [ 0.113936] pci 0000:00:01.0: [1002:5a3f] type 01 class 0x060400 [ 0.114097] pci 0000:00:13.0: [1002:4374] type 00 class 0x0c0310 [ 0.114123] pci 0000:00:13.0: reg 0x10: [mem 0xc0404000-0xc0404fff] [ 0.114305] pci 0000:00:13.1: [1002:4375] type 00 class 0x0c0310 [ 0.114330] pci 0000:00:13.1: reg 0x10: [mem 0xc0405000-0xc0405fff] [ 0.114514] pci 0000:00:13.2: [1002:4373] type 00 class 0x0c0320 [ 0.114544] pci 0000:00:13.2: reg 0x10: [mem 0xc0406000-0xc0406fff] [ 0.114677] pci 0000:00:13.2: supports D1 D2 [ 0.114681] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.114793] pci 0000:00:14.0: [1002:4372] type 00 class 0x0c0500 [ 0.114815] pci 0000:00:14.0: reg 0x10: [io 0x8400-0x840f] [ 0.114832] pci 0000:00:14.0: reg 0x14: [mem 0xc0407000-0xc04073ff] [ 0.114908] HPET not enabled in BIOS. You might try hpet=force boot option [ 0.116101] pci 0000:00:14.1: [1002:4376] type 00 class 0x01018a [ 0.116131] pci 0000:00:14.1: reg 0x10: [io 0x01f0-0x01f7] [ 0.116149] pci 0000:00:14.1: reg 0x14: [io 0x03f4-0x03f7] [ 0.116166] pci 0000:00:14.1: reg 0x18: [io 0x0170-0x0177] [ 0.116183] pci 0000:00:14.1: reg 0x1c: [io 0x0374-0x0377] [ 0.116200] pci 0000:00:14.1: reg 0x20: [io 0x8410-0x841f] [ 0.116371] pci 0000:00:14.2: [1002:437b] type 00 class 0x040300 [ 0.116415] pci 0000:00:14.2: reg 0x10: [mem 0xc0400000-0xc0403fff 64bit] [ 0.116552] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold [ 0.116606] pci 0000:00:14.2: System wakeup disabled by ACPI [ 0.116710] pci 0000:00:14.3: [1002:4377] type 00 class 0x060100 [ 0.116905] pci 0000:00:14.4: [1002:4371] type 01 class 0x060401 [ 0.117005] pci 0000:00:14.4: System wakeup disabled by ACPI [ 0.117195] pci 0000:01:05.0: [1002:5a62] type 00 class 0x030000 [ 0.117213] pci 0000:01:05.0: reg 0x10: [mem 0xd0000000-0xdfffffff pref] [ 0.117223] pci 0000:01:05.0: reg 0x14: [io 0x9000-0x90ff] [ 0.117232] pci 0000:01:05.0: reg 0x18: [mem 0xc0000000-0xc000ffff] [ 0.117260] pci 0000:01:05.0: reg 0x30: [mem 0x00000000-0x0001ffff pref] [ 0.117291] pci 0000:01:05.0: supports D1 D2 [ 0.117368] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.117422] pci 0000:00:01.0: bridge window [io 0x9000-0x9fff] [ 0.117427] pci 0000:00:01.0: bridge window [mem 0xc0000000-0xc00fffff] [ 0.117432] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff pref] [ 0.117597] pci 0000:02:05.0: [10ec:8139] type 00 class 0x020000 [ 0.117634] pci 0000:02:05.0: reg 0x10: [io 0xa000-0xa0ff] [ 0.117654] pci 0000:02:05.0: reg 0x14: [mem 0xc0100000-0xc01000ff] [ 0.117794] pci 0000:02:05.0: supports D1 D2 [ 0.117798] pci 0000:02:05.0: PME# supported from D1 D2 D3hot D3cold [ 0.117843] pci 0000:02:05.0: System wakeup disabled by ACPI [ 0.117958] pci 0000:02:07.0: [168c:001a] type 00 class 0x020000 [ 0.117994] pci 0000:02:07.0: reg 0x10: [mem 0xc0110000-0xc011ffff] [ 0.118249] pci 0000:02:09.0: [1180:0476] type 02 class 0x060700 [ 0.118281] pci 0000:02:09.0: proprietary Ricoh MMC controller disabled (via cardbus function) [ 0.118335] pci 0000:02:09.0: MMC cards are now supported by standard SDHCI controller [ 0.118410] pci 0000:02:09.0: reg 0x10: [mem 0xc0101000-0xc0101fff] [ 0.118467] pci 0000:02:09.0: supports D1 D2 [ 0.118471] pci 0000:02:09.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.118571] pci 0000:02:09.1: [1180:0822] type 00 class 0x080500 [ 0.118606] pci 0000:02:09.1: reg 0x10: [mem 0xc0100400-0xc01004ff] [ 0.118761] pci 0000:02:09.1: supports D1 D2 [ 0.118764] pci 0000:02:09.1: PME# supported from D0 D1 D2 D3hot D3cold [ 0.118868] pci 0000:02:09.2: [1180:0592] type 00 class 0x088000 [ 0.118903] pci 0000:02:09.2: reg 0x10: [mem 0xc0100c00-0xc0100cff] [ 0.119059] pci 0000:02:09.2: supports D1 D2 [ 0.119062] pci 0000:02:09.2: PME# supported from D0 D1 D2 D3hot D3cold [ 0.119167] pci 0000:02:09.3: [1180:0852] type 00 class 0x088000 [ 0.119202] pci 0000:02:09.3: reg 0x10: [mem 0xc0102000-0xc01020ff] [ 0.119357] pci 0000:02:09.3: supports D1 D2 [ 0.119360] pci 0000:02:09.3: PME# supported from D0 D1 D2 D3hot D3cold [ 0.119505] pci 0000:00:14.4: PCI bridge to [bus 02-05] (subtractive decode) [ 0.119563] pci 0000:00:14.4: bridge window [io 0xa000-0xafff] [ 0.119570] pci 0000:00:14.4: bridge window [mem 0xf0200000-0xf02fffff] [ 0.119578] pci 0000:00:14.4: bridge window [mem 0xf0300000-0xf03fffff pref] [ 0.119581] pci 0000:00:14.4: bridge window [io 0x0000-0xffff] (subtractive decode) [ 0.119585] pci 0000:00:14.4: bridge window [mem 0x00000000-0xfffffffff] (subtractive decode) [ 0.119667] pci_bus 0000:03: busn_res: can not insert [bus 03-ff] under [bus 02-05] (conflicts with (null) [bus 02-05]) [ 0.119675] pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 04 [ 0.119698] pci_bus 0000:00: on NUMA node 0 [ 0.119945] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. [ 0.120278] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. [ 0.120630] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. [ 0.120981] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. [ 0.121332] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. [ 0.121683] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. [ 0.122033] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. [ 0.122383] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. [ 0.122733] ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled. [ 0.123451] ACPI: Enabled 1 GPEs in block 00 to 1F [ 0.123583] ACPI: \_SB_.PCI0: notify handler is installed [ 0.123628] Found 1 acpi root devices [ 0.123721] ACPI : EC: GPE = 0x3, I/O: command/status = 0x66, data = 0x62 [ 0.123779] ACPI : EC: 0 stale EC events cleared [ 0.124046] vgaarb: setting as boot device: PCI:0000:01:05.0 [ 0.124077] vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none [ 0.124131] vgaarb: loaded [ 0.124176] vgaarb: bridge control possible 0000:01:05.0 [ 0.124559] SCSI subsystem initialized [ 0.124629] libata version 3.00 loaded. [ 0.124629] ACPI: bus type USB registered [ 0.124629] usbcore: registered new interface driver usbfs [ 0.124629] usbcore: registered new interface driver hub [ 0.124629] usbcore: registered new device driver usb [ 0.124629] PCI: Using ACPI for IRQ routing [ 0.124629] PCI: pci_cache_line_size set to 64 bytes [ 0.124629] e820: reserve RAM buffer [mem 0x0009dc00-0x0009ffff] [ 0.124629] e820: reserve RAM buffer [mem 0x37e90000-0x37ffffff] [ 0.124629] NetLabel: Initializing [ 0.124629] NetLabel: domain hash size = 128 [ 0.124629] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.124629] NetLabel: unlabeled traffic allowed by default [ 0.124629] Switched to clocksource refined-jiffies [ 0.139923] AppArmor: AppArmor Filesystem Enabled [ 0.140103] pnp: PnP ACPI init [ 0.140183] ACPI: bus type PNP registered [ 0.140398] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved [ 0.140398] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.140555] pnp 00:01: [dma 4] [ 0.140607] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.140682] pnp 00:02: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.140738] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.140791] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.140849] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 (active) [ 0.140901] pnp 00:06: Plug and Play ACPI device, IDs PNP0f13 (active) [ 0.141002] system 00:07: [io 0x1080] has been reserved [ 0.141054] system 00:07: [io 0x0220-0x022f] has been reserved [ 0.141103] system 00:07: [io 0x040b] has been reserved [ 0.141151] system 00:07: [io 0x04d0-0x04d1] has been reserved [ 0.141199] system 00:07: [io 0x04d6] has been reserved [ 0.141246] system 00:07: [io 0x0530-0x0537] has been reserved [ 0.141294] system 00:07: [io 0x0c00-0x0c01] has been reserved [ 0.141342] system 00:07: [io 0x0c14] has been reserved [ 0.141389] system 00:07: [io 0x0c50-0x0c52] has been reserved [ 0.141437] system 00:07: [io 0x0c6c] has been reserved [ 0.141484] system 00:07: [io 0x0c6f] has been reserved [ 0.141532] system 00:07: [io 0x0cd4-0x0cd5] has been reserved [ 0.141580] system 00:07: [io 0x0cd6-0x0cd7] has been reserved [ 0.141627] system 00:07: [io 0x0cd8-0x0cdf] has been reserved [ 0.141676] system 00:07: [io 0x8000-0x805f] could not be reserved [ 0.141724] system 00:07: [io 0x8100-0x81ff window] has been reserved [ 0.141773] system 00:07: [io 0x8210-0x821f] has been reserved [ 0.141820] system 00:07: [io 0x0f40-0x0f47] has been reserved [ 0.141868] system 00:07: [io 0x0280-0x0293] has been reserved [ 0.141925] system 00:07: [io 0x087f] has been reserved [ 0.141974] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.142080] pnp 00:08: disabling [mem 0x00000000-0x00000fff] because it overlaps 0000:01:05.0 BAR 6 [mem 0x00000000-0x0001ffff pref] [ 0.142200] system 00:08: [mem 0x000e0000-0x000fffff] could not be reserved [ 0.142253] system 00:08: [mem 0xfff00000-0xffffffff] has been reserved [ 0.142303] system 00:08: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.142370] pnp: PnP ACPI: found 9 devices [ 0.142419] ACPI: bus type PNP unregistered [ 0.142468] PnPBIOS: Disabled by ACPI PNP [ 0.181058] Switched to clocksource acpi_pm [ 0.181156] pci 0000:01:05.0: BAR 6: assigned [mem 0xc0020000-0xc003ffff pref] [ 0.181236] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.181284] pci 0000:00:01.0: bridge window [io 0x9000-0x9fff] [ 0.181334] pci 0000:00:01.0: bridge window [mem 0xc0000000-0xc00fffff] [ 0.181383] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff pref] [ 0.181452] pci 0000:02:09.0: res[15]=[mem 0x04000000-0x03ffffff pref] get_res_add_size add_size 4000000 [ 0.181456] pci 0000:02:09.0: res[16]=[mem 0x04000000-0x03ffffff] get_res_add_size add_size 4000000 [ 0.181459] pci 0000:02:09.0: res[13]=[io 0x0100-0x00ff] get_res_add_size add_size 100 [ 0.181463] pci 0000:02:09.0: res[14]=[io 0x0100-0x00ff] get_res_add_size add_size 100 [ 0.181470] pci 0000:02:09.0: BAR 15: assigned [mem 0x38000000-0x3bffffff pref] [ 0.181524] pci 0000:02:09.0: BAR 16: assigned [mem 0x3c000000-0x3fffffff] [ 0.181573] pci 0000:02:09.0: BAR 13: assigned [io 0xa400-0xa4ff] [ 0.181621] pci 0000:02:09.0: BAR 14: assigned [io 0xa800-0xa8ff] [ 0.181669] pci 0000:02:09.0: CardBus bridge to [bus 03-04] [ 0.181717] pci 0000:02:09.0: bridge window [io 0xa400-0xa4ff] [ 0.181769] pci 0000:02:09.0: bridge window [io 0xa800-0xa8ff] [ 0.181821] pci 0000:02:09.0: bridge window [mem 0x38000000-0x3bffffff pref] [ 0.181878] pci 0000:02:09.0: bridge window [mem 0x3c000000-0x3fffffff] [ 0.181930] pci 0000:00:14.4: PCI bridge to [bus 02-05] [ 0.181979] pci 0000:00:14.4: bridge window [io 0xa000-0xafff] [ 0.182032] pci 0000:00:14.4: bridge window [mem 0xf0200000-0xf02fffff] [ 0.182084] pci 0000:00:14.4: bridge window [mem 0xf0300000-0xf03fffff pref] [ 0.182145] pci_bus 0000:00: resource 4 [io 0x0000-0xffff] [ 0.182149] pci_bus 0000:00: resource 5 [mem 0x00000000-0xfffffffff] [ 0.182152] pci_bus 0000:01: resource 0 [io 0x9000-0x9fff] [ 0.182156] pci_bus 0000:01: resource 1 [mem 0xc0000000-0xc00fffff] [ 0.182159] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff pref] [ 0.182163] pci_bus 0000:02: resource 0 [io 0xa000-0xafff] [ 0.182166] pci_bus 0000:02: resource 1 [mem 0xf0200000-0xf02fffff] [ 0.182170] pci_bus 0000:02: resource 2 [mem 0xf0300000-0xf03fffff pref] [ 0.182173] pci_bus 0000:02: resource 4 [io 0x0000-0xffff] [ 0.182176] pci_bus 0000:02: resource 5 [mem 0x00000000-0xfffffffff] [ 0.182180] pci_bus 0000:03: resource 0 [io 0xa400-0xa4ff] [ 0.182183] pci_bus 0000:03: resource 1 [io 0xa800-0xa8ff] [ 0.182186] pci_bus 0000:03: resource 2 [mem 0x38000000-0x3bffffff pref] [ 0.182190] pci_bus 0000:03: resource 3 [mem 0x3c000000-0x3fffffff] [ 0.182266] NET: Registered protocol family 2 [ 0.182770] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.182878] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.183035] TCP: Hash tables configured (established 8192 bind 8192) [ 0.183214] TCP: reno registered [ 0.183264] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.183340] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.183503] NET: Registered protocol family 1 [ 0.183572] pci 0000:00:01.0: MSI quirk detected; subordinate MSI disabled [ 0.288276] pci 0000:01:05.0: Video device with shadowed ROM [ 0.288306] PCI: CLS 32 bytes, default 64 [ 0.288408] Trying to unpack rootfs image as initramfs... [ 0.865709] Freeing initrd memory: 18348K (f5c1a000 - f6e05000) [ 0.866483] microcode: CPU0 sig=0x6f6, pf=0x20, revision=0xc7 [ 0.866535] microcode: CPU1 sig=0x6f6, pf=0x20, revision=0xc7 [ 0.866747] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba [ 0.866801] Scanning for low memory corruption every 60 seconds [ 0.867301] Initialise system trusted keyring [ 0.867437] audit: initializing netlink socket (disabled) [ 0.867523] type=2000 audit(1448758177.863:1): initialized [ 0.899696] bounce pool size: 64 pages [ 0.899770] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.901948] zbud: loaded [ 0.902140] VFS: Disk quotas dquot_6.5.2 [ 0.902258] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.903122] fuse init (API version 7.22) [ 0.903316] msgmni has been set to 1740 [ 0.903465] Key type big_key registered [ 0.904664] Key type asymmetric registered [ 0.904714] Asymmetric key parser 'x509' registered [ 0.904815] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.904947] io scheduler noop registered [ 0.905000] io scheduler deadline registered (default) [ 0.905088] io scheduler cfq registered [ 0.905329] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.905400] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.905529] intel_idle: does not run on family 6 model 15 [ 0.905540] ipmi message handler version 39.2 [ 0.905830] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.906090] ACPI: AC Adapter [ADP1] (on-line) [ 0.906389] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 [ 0.907000] ACPI: Power Button [PWRB] [ 0.907104] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1 [ 0.907177] ACPI: Lid Switch [LID0] [ 0.907275] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2 [ 0.907333] ACPI: Sleep Button [SLPB] [ 0.907447] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 0.907504] ACPI: Power Button [PWRF] [ 0.907631] ACPI: Fan [FAN0] (off) [ 0.909526] tsc: Marking TSC unstable due to TSC halts in idle [ 0.909582] ACPI: acpi_idle registered with cpuidle [ 0.910888] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.910940] ACPI: Thermal Zone [TZ00] (66 C) [ 0.911028] GHES: HEST is not enabled! [ 0.911213] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.911274] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.911340] ACPI: Battery Slot [BAT1] (battery absent) [ 0.911417] isapnp: Scanning for PnP cards... [ 0.913326] Linux agpgart interface v0.103 [ 0.915613] brd: module loaded [ 0.916799] loop: module loaded [ 0.917510] libphy: Fixed MDIO Bus: probed [ 0.917725] tun: Universal TUN/TAP device driver, 1.6 [ 0.917774] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 0.917868] PPP generic driver version 2.4.2 [ 0.917974] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.918028] ehci-pci: EHCI PCI platform driver [ 0.918241] ehci-pci 0000:00:13.2: EHCI Host Controller [ 0.918296] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 1 [ 0.918448] ehci-pci 0000:00:13.2: irq 19, io mem 0xc0406000 [ 0.928052] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 0.928202] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.928254] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.928309] usb usb1: Product: EHCI Host Controller [ 0.928356] usb usb1: Manufacturer: Linux 3.13.0-68-generic ehci_hcd [ 0.928403] usb usb1: SerialNumber: 0000:00:13.2 [ 0.928596] hub 1-0:1.0: USB hub found [ 0.928655] hub 1-0:1.0: 8 ports detected [ 0.928978] ehci-platform: EHCI generic platform driver [ 0.929035] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.929083] ohci-pci: OHCI PCI platform driver [ 0.929228] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 0.929280] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 2 [ 0.929350] ohci-pci 0000:00:13.0: irq 19, io mem 0xc0404000 [ 0.988095] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 0.988144] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.988197] usb usb2: Product: OHCI PCI host controller [ 0.988244] usb usb2: Manufacturer: Linux 3.13.0-68-generic ohci_hcd [ 0.988293] usb usb2: SerialNumber: 0000:00:13.0 [ 0.988466] hub 2-0:1.0: USB hub found [ 0.988531] hub 2-0:1.0: 4 ports detected [ 0.988818] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 0.988875] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 3 [ 0.988946] ohci-pci 0000:00:13.1: irq 19, io mem 0xc0405000 [ 1.048098] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.048150] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.048203] usb usb3: Product: OHCI PCI host controller [ 1.048250] usb usb3: Manufacturer: Linux 3.13.0-68-generic ohci_hcd [ 1.048297] usb usb3: SerialNumber: 0000:00:13.1 [ 1.048473] hub 3-0:1.0: USB hub found [ 1.048534] hub 3-0:1.0: 4 ports detected [ 1.048744] ohci-platform: OHCI generic platform driver [ 1.048803] uhci_hcd: USB Universal Host Controller Interface driver [ 1.048970] i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 [ 1.051780] i8042: Detected active multiplexing controller, rev 1.1 [ 1.053774] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.053826] serio: i8042 AUX0 port at 0x60,0x64 irq 12 [ 1.053915] serio: i8042 AUX1 port at 0x60,0x64 irq 12 [ 1.053995] serio: i8042 AUX2 port at 0x60,0x64 irq 12 [ 1.054071] serio: i8042 AUX3 port at 0x60,0x64 irq 12 [ 1.054281] mousedev: PS/2 mouse device common for all mice [ 1.054772] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 1.054852] rtc_cmos 00:03: alarms up to one month, 114 bytes nvram [ 1.055008] device-mapper: uevent: version 1.0.3 [ 1.055162] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com [ 1.055246] platform eisa.0: Probing EISA bus 0 [ 1.055302] platform eisa.0: Cannot allocate resource for EISA slot 1 [ 1.055385] platform eisa.0: Cannot allocate resource for EISA slot 8 [ 1.055433] platform eisa.0: EISA: Detected 0 cards [ 1.055489] cpufreq-nforce2: No nForce2 chipset. [ 1.055539] ledtrig-cpu: registered to indicate activity on CPUs [ 1.055807] TCP: cubic registered [ 1.056044] NET: Registered protocol family 10 [ 1.056437] NET: Registered protocol family 17 [ 1.056506] Key type dns_resolver registered [ 1.056793] Using IPI No-Shortcut mode [ 1.056952] Loading compiled-in X.509 certificates [ 1.062399] Loaded X.509 cert 'Magrathea: Glacier signing key: 9ba6965428d40bf71e0c5eaf1a6fc16c1a2b9ed3' [ 1.062478] registered taskstats version 1 [ 1.065791] Key type trusted registered [ 1.070844] Key type encrypted registered [ 1.070895] AppArmor: AppArmor sha1 policy hashing enabled [ 1.070944] IMA: No TPM chip found, activating TPM-bypass! [ 1.071353] regulator-dummy: disabling [ 1.071466] Magic number: 7:993:810 [ 1.071672] rtc_cmos 00:03: setting system clock to 2015-11-29 00:49:39 UTC (1448758179) [ 1.072229] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 1.072281] EDD information not available. [ 1.072384] PM: Hibernation image not present or could not be loaded. [ 1.079980] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 1.268349] isapnp: No Plug & Play device found [ 1.269152] Freeing unused kernel memory: 880K (c19c1000 - c1a9d000) [ 1.269281] Write protecting the kernel text: 6564k [ 1.269465] Write protecting the kernel read-only data: 2776k [ 1.269512] NX-protecting the kernel data: 5724k [ 1.289179] systemd-udevd[96]: starting version 204 [ 1.296154] usb 1-2: new high-speed USB device number 3 using ehci-pci [ 1.327527] scsi0 : pata_atiixp [ 1.327965] scsi1 : pata_atiixp [ 1.328114] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8410 irq 14 [ 1.328166] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8418 irq 15 [ 1.360949] sdhci: Secure Digital Host Controller Interface driver [ 1.361009] sdhci: Copyright(c) Pierre Ossman [ 1.367730] sdhci-pci 0000:02:09.1: SDHCI controller found [1180:0822] (rev 18) [ 1.367980] sdhci-pci 0000:02:09.1: Will use DMA mode even though HW doesn't fully claim to support it. [ 1.368422] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 1.368488] sdhci-pci 0000:02:09.1: dummy supplies not allowed [ 1.368535] mmc0: no vqmmc regulator found [ 1.368581] sdhci-pci 0000:02:09.1: dummy supplies not allowed [ 1.368627] mmc0: no vmmc regulator found [ 1.368803] mmc0: SDHCI controller on PCI [0000:02:09.1] using DMA [ 1.368876] 8139cp 0000:02:05.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too [ 1.387947] 8139too: 8139too Fast Ethernet driver 0.9.28 [ 1.389575] 8139too 0000:02:05.0 eth0: RealTek RTL8139 at 0x0001a000, 00:13:77:31:02:bd, IRQ 18 [ 1.429743] usb 1-2: New USB device found, idVendor=05e3, idProduct=0608 [ 1.429807] usb 1-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.429867] usb 1-2: Product: USB2.0 Hub [ 1.430406] hub 1-2:1.0: USB hub found [ 1.430851] hub 1-2:1.0: 4 ports detected [ 1.492901] ata1.00: ATA-7: FUJITSU MHV2100AH PL, 004200A0, max UDMA/100 [ 1.492956] ata1.00: 195371568 sectors, multi 16: LBA48 [ 1.509205] ata1.00: configured for UDMA/100 [ 1.509462] ata2.00: ATAPI: DV-W28EC, S.0A, max UDMA/33 [ 1.509484] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHV2100A 0042 PQ: 0 ANSI: 5 [ 1.509752] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB) [ 1.509767] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.509961] sd 0:0:0:0: [sda] Write Protect is off [ 1.510019] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.510058] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.541305] ata2.00: configured for UDMA/33 [ 1.562719] scsi 1:0:0:0: CD-ROM TEAC DV-W28EC S.0A PQ: 0 ANSI: 5 [ 1.574744] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.574799] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.575017] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 1.575125] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 1.576716] sda: sda1 < sda5 sda6 sda7 > [ 1.577505] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.736072] usb 2-1: new low-speed USB device number 2 using ohci-pci [ 1.945143] usb 2-1: New USB device found, idVendor=046d, idProduct=c03d [ 1.945316] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.945377] usb 2-1: Product: USB-PS/2 Optical Mouse [ 1.945532] usb 2-1: Manufacturer: Logitech [ 1.959934] hidraw: raw HID events driver (C) Jiri Kosina [ 1.973667] usbcore: registered new interface driver usbhid [ 1.973728] usbhid: USB HID core driver [ 1.980589] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:13.0/usb2/2-1/2-1:1.0/input/input13 [ 1.981453] hid-generic 0003:046D:C03D.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:13.0-1/input0 [ 2.111752] psmouse serio4: synaptics: Touchpad model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04713/0x200000/0x0, board id: 0, fw id: 131143 [ 2.148147] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input12 [ 7.099290] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 7.796856] random: nonblocking pool is initialized [ 9.396640] systemd-udevd[207]: starting version 204 [ 10.877990] ACPI: Video Device [ATIM] (multi-head: yes rom: no post: no) [ 10.878229] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:16/LNXVIDEO:00/input/input14 [ 11.192527] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0x8400, revision 0 [ 11.279607] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 11.435096] yenta_cardbus 0000:02:09.0: CardBus bridge found [144d:c02b] [ 11.560919] yenta_cardbus 0000:02:09.0: ISA IRQ mask 0x0cb8, PCI irq 20 [ 11.560983] yenta_cardbus 0000:02:09.0: Socket status: 30000006 [ 11.561040] yenta_cardbus 0000:02:09.0: pcmcia: parent PCI bridge window: [io 0xa000-0xafff] [ 11.561099] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa000-0xafff: [ 11.563088] excluding 0xa000-0xa0ff 0xa400-0xa4ff 0xa800-0xa8ff [ 11.569718] yenta_cardbus 0000:02:09.0: pcmcia: parent PCI bridge window: [mem 0xf0200000-0xf02fffff] [ 11.569773] pcmcia_socket pcmcia_socket0: cs: memory probe 0xf0200000-0xf02fffff: [ 11.569837] clean. [ 11.569883] yenta_cardbus 0000:02:09.0: pcmcia: parent PCI bridge window: [mem 0xf0300000-0xf03fffff pref] [ 11.569938] pcmcia_socket pcmcia_socket0: cs: memory probe 0xf0300000-0xf03fffff: [ 11.570009] excluding 0xf0300000-0xf03fffff [ 11.626447] r592: driver successfully loaded [ 11.953339] [drm] Initialized drm 1.1.0 20060810 [ 12.046315] cfg80211: Calling CRDA to update world regulatory domain [ 12.088871] samsung_laptop: detected SABI interface: SwSmi@ [ 12.330748] r852: Non dma capable device detected, dma disabled [ 12.330827] r852: driver loaded successfully [ 12.735099] ath5k 0000:02:07.0: registered as 'phy0' [ 13.014969] [drm] VGACON disable radeon kernel modesetting. [ 13.015031] [drm] radeon userspace modesetting enabled. [ 13.015794] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 13.015848] [drm] No driver support for vblank timestamp query. [ 13.015899] [drm] Initialized radeon 1.34.0 20080528 for 0000:01:05.0 on minor 0 [ 13.064994] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: [ 13.067225] excluding 0x170-0x177 0x1f0-0x1f7 0x220-0x22f 0x280-0x297 0x370-0x377 [ 13.069227] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: [ 13.070113] excluding 0x3f0-0x3f7 0x408-0x40f 0x4d0-0x4d7 [ 13.071173] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: [ 13.072152] excluding 0x878-0x87f [ 13.072737] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: [ 13.073390] excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf [ 13.074433] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: [ 13.074514] excluding 0xc0000-0xcffff 0xdc000-0xdffff 0xe4000-0xfffff [ 13.074859] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: [ 13.074968] clean. [ 13.075056] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: [ 13.075156] clean. [ 13.075245] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: [ 13.076817] clean. [ 13.121707] hda-intel 0000:00:14.2: Using LPIB position fix [ 13.121846] snd_hda_intel 0000:00:14.2: irq 40 for MSI/MSI-X [ 13.126536] hda-intel 0000:00:14.2: Enable sync_write for stable communication [ 13.238645] SKU: Nid=0x0 sku_cfg=0x0000852d [ 13.238720] SKU: port_connectivity=0x0 [ 13.238773] SKU: enable_pcbeep=0x1 [ 13.238828] SKU: check_sum=0x00000000 [ 13.238882] SKU: customization=0x00000000 [ 13.238933] SKU: external_amp=0x5 [ 13.238989] SKU: platform_type=0x1 [ 13.239041] SKU: swap=0x0 [ 13.239094] SKU: override=0x1 [ 13.239331] autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker [ 13.239388] speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) [ 13.239448] hp_outs=1 (0x15/0x0/0x0/0x0/0x0) [ 13.239520] mono: mono_out=0x0 [ 13.239591] inputs: [ 13.239666] Mic=0x18 [ 13.239740] realtek: Enabling init ASM_ID=0x852d CODEC_ID=10ec0262 [ 13.253147] input: HDA ATI SB Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input16 [ 13.253356] input: HDA ATI SB Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input15 [ 13.403927] ath: EEPROM regdomain: 0x65 [ 13.403933] ath: EEPROM indicates we should expect a direct regpair map [ 13.403937] ath: Country alpha2 being used: 00 [ 13.403940] ath: Regpair used: 0x65 [ 13.520871] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 13.521301] ath5k: phy0: Atheros AR2413 chip found (MAC: 0x78, PHY: 0x45) [ 13.835034] cfg80211: World regulatory domain updated: [ 13.835095] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 13.835148] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 13.835200] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 13.835253] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 13.835305] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 13.835357] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 14.046939] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.046952] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 28.462265] init: plymouth-upstart-bridge main process (728) terminated with status 1 [ 28.462292] init: plymouth-upstart-bridge main process ended, respawning [ 28.518195] init: plymouth-upstart-bridge main process (761) terminated with status 1 [ 28.518220] init: plymouth-upstart-bridge main process ended, respawning [ 28.555812] init: plymouth-upstart-bridge main process (765) terminated with status 1 [ 28.555840] init: plymouth-upstart-bridge main process ended, respawning [ 28.575142] init: plymouth-upstart-bridge main process (768) terminated with status 1 [ 28.575167] init: plymouth-upstart-bridge main process ended, respawning [ 28.605615] init: plymouth-upstart-bridge main process (771) terminated with status 1 [ 28.605642] init: plymouth-upstart-bridge main process ended, respawning [ 28.631176] init: plymouth-upstart-bridge main process (776) terminated with status 1 [ 28.631204] init: plymouth-upstart-bridge main process ended, respawning [ 28.648333] init: plymouth-upstart-bridge main process (779) terminated with status 1 [ 28.648358] init: plymouth-upstart-bridge main process ended, respawning [ 28.680305] init: plymouth-upstart-bridge main process (781) terminated with status 1 [ 28.680332] init: plymouth-upstart-bridge main process ended, respawning [ 28.697585] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: [ 28.700119] excluding 0x170-0x177 0x1f0-0x1f7 0x220-0x22f 0x280-0x297 0x370-0x377 [ 28.701475] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: [ 28.702176] excluding 0x3f0-0x3f7 0x408-0x40f 0x4d0-0x4d7 [ 28.702786] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: [ 28.703428] excluding 0x878-0x87f [ 28.703775] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: [ 28.704461] excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf [ 28.704927] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: [ 28.704937] excluding 0xc0000-0xcffff 0xdc000-0xdffff 0xe4000-0xfffff [ 28.704976] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: [ 28.704997] clean. [ 28.705020] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: [ 28.705041] clean. [ 28.705064] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: [ 28.709326] clean. [ 28.742694] lp: driver loaded but no devices found [ 28.837786] ppdev: user-space parallel port driver [ 42.813970] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro [ 43.026430] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null) [ 44.336611] init: failsafe main process (1031) killed by TERM signal [ 44.765499] type=1400 audit(1448758223.189:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=1141 comm="apparmor_parser" [ 44.765514] type=1400 audit(1448758223.189:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1141 comm="apparmor_parser" [ 44.765523] type=1400 audit(1448758223.189:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=1141 comm="apparmor_parser" [ 44.766233] type=1400 audit(1448758223.189:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=1140 comm="apparmor_parser" [ 44.766243] type=1400 audit(1448758223.189:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="chromium" pid=1140 comm="apparmor_parser" [ 44.766289] type=1400 audit(1448758223.189:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1141 comm="apparmor_parser" [ 44.766299] type=1400 audit(1448758223.189:8): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=1141 comm="apparmor_parser" [ 44.766695] type=1400 audit(1448758223.189:9): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="chromium" pid=1140 comm="apparmor_parser" [ 44.766709] type=1400 audit(1448758223.189:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=1141 comm="apparmor_parser" [ 44.776126] type=1400 audit(1448758223.201:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=1144 comm="apparmor_parser" [ 45.961470] init: cups main process (1216) killed by HUP signal [ 45.961494] init: cups main process ended, respawning [ 46.153813] Bluetooth: Core ver 2.17 [ 46.153878] NET: Registered protocol family 31 [ 46.153881] Bluetooth: HCI device and connection manager initialized [ 46.153923] Bluetooth: HCI socket layer initialized [ 46.153927] Bluetooth: L2CAP socket layer initialized [ 46.153939] Bluetooth: SCO socket layer initialized [ 46.253610] Bluetooth: RFCOMM TTY layer initialized [ 46.253631] Bluetooth: RFCOMM socket layer initialized [ 46.253655] Bluetooth: RFCOMM ver 1.11 [ 46.300131] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 46.300137] Bluetooth: BNEP filters: protocol multicast [ 46.300155] Bluetooth: BNEP socket layer initialized [ 49.283321] 8139too 0000:02:05.0 eth0: link down [ 49.283433] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 49.283922] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 49.298375] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 49.298750] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 51.348880] wlan0: authenticate with 18:83:bf:eb:3d:e7 [ 51.360676] wlan0: send auth to 18:83:bf:eb:3d:e7 (try 1/3) [ 51.364687] wlan0: authenticated [ 51.368151] wlan0: associate with 18:83:bf:eb:3d:e7 (try 1/3) [ 51.370904] wlan0: RX AssocResp from 18:83:bf:eb:3d:e7 (capab=0x411 status=0 aid=4) [ 51.371293] wlan0: associated [ 51.371312] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 51.373858] cfg80211: Calling CRDA for country: DE [ 51.379730] ath: EEPROM regdomain: 0x8114 [ 51.379736] ath: EEPROM indicates we should expect a country code [ 51.379739] ath: doing EEPROM country->regdmn map search [ 51.379741] ath: country maps to regdmn code: 0x37 [ 51.379744] ath: Country alpha2 being used: DE [ 51.379746] ath: Regpair used: 0x37 [ 51.379749] ath: regdomain 0x8114 dynamically updated by country IE [ 51.379751] cfg80211: Regulatory domain changed to country: DE [ 51.379754] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 51.379757] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 51.379760] cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 51.379763] cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 51.379766] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm) [ 51.379768] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 52.828047] init: plymouth-upstart-bridge main process ended, respawning [ 52.869024] init: plymouth-upstart-bridge main process (1539) terminated with status 1 [ 52.869060] init: plymouth-upstart-bridge main process ended, respawning [ 75.399934] audit_printk_skb: 87 callbacks suppressed [ 75.399941] type=1400 audit(1448758253.821:41): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=2586 comm="apparmor_parser" [ 75.399954] type=1400 audit(1448758253.821:42): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2586 comm="apparmor_parser" [ 75.400757] type=1400 audit(1448758253.825:43): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2586 comm="apparmor_parser" [ 231.699483] perf samples too long (2509 > 2500), lowering kernel.perf_event_max_sample_rate to 50000 [ 422.298607] perf samples too long (5021 > 5000), lowering kernel.perf_event_max_sample_rate to 25000 [ 605.004449] ath5k: ath5k_hw_get_isr: ISR: 0x00000080 IMR: 0x00000000 [ 2006.917218] perf samples too long (10051 > 10000), lowering kernel.perf_event_max_sample_rate to 12500 |
Kann man da noch etwas retten?