Ich habe noch ein paar Rohlinge geschrottet & schon wieder keine mehr - Problem immer noch vorhanden.
K3b gibt Folgendes aus (um wahrscheinlich Unwichtiges gekürzt):
Devices
-----------------------
TSSTcorp CDDVDW SH-222BB SB00 (/dev/sr0, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite, Layer Jump] [%7]
K3b::DataTrackReader
-----------------------
reading sectors 0 to 358319 with sector size 2048. Length: 358320 sectors, 733839360 bytes.
using buffer size of 128 blocks.
Problem while reading. Retrying from sector 147072.
Read error in sector 147171.
Read a total of 147072 sectors (301203456 bytes)
System
-----------------------
K3b Version: 2.0.2
KDE Version: 4.7.4 (4.7.4)
QT Version: 4.7.4
Kernel: 3.0.0-17-generic
Used versions
-----------------------
cdrecord: 3.1a03
cdrecord
-----------------------
scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
SCSI buffer size: 64512
cdrecord: Warning: Cannot read drive buffer.
cdrecord: Warning: The DMA speed test has been skipped.
Cdrecord-ProDVD-ProBD-Clone 3.01a03 (i686-pc-linux-gnu) Copyright (C) 1995-2010 Joerg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.9'.
Driveropts: 'burnfree'
atapi: 1
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'TSSTcorp'
Identifikation : 'CDDVDW SH-222BB '
Revision : 'SB00'
Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM.
Current: CD-R
Profile: DVD-R/DL sequential recording
Profile: DVD-R/DL layer jump recording
Profile: DVD+R/DL
Profile: DVD+R
Profile: DVD+RW
Profile: DVD-RW sequential recording
Profile: DVD-RW restricted overwrite
Profile: DVD-RAM
Profile: DVD-R sequential recording
Profile: DVD-ROM
Profile: CD-RW
Profile: CD-R (current)
Profile: CD-ROM
Profile: Removable Disk
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1286912 = 1256 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 699 MB
Total size: 803 MB (79:37.60) = 358320 sectors
Lout start: 804 MB (79:39/45) = 358320 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Disk Is not unrestricted
Disk Is not erasable
Disk sub type: Medium Type A, high Beta category (A+) (3)
ATIP start of lead in: -11634 (97:26/66)
ATIP start of lead out: 359846 (79:59/71)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Capacity Blklen/Sparesz. Format-type Type
445350 2048 0x00 No Media Present or Unknown Capacity
Blocks total: 359846 Blocks current: 359846 Blocks remaining: 1526
Starting to write CD/DVD/BD at speed 16 in real SAO mode for single session.
Last chance to quit, starting real write in 3 seconds.
2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
Performing OPC...
Sending CUE sheet...
cdrecord: WARNING: Drive returns wrong startsec (0) using -150
Writing pregap for track 1 at -150
Starting new track at sector: 0
Track 01: 0 of 699 MB written.
...
...
...
Track 01: 699 of 699 MB written (fifo 100%) [buf 99%] 16,9x.
Track 01: Total bytes read/written: 733839360/733839360 (358320 sectors).
Writing time: 317.395s
Average write speed 15,4x.
Min drive buffer fill was 91%
Fixating...
Fixating time: 8.033s
cdrecord: fifo had 11559 puts and 11559 gets.
cdrecord: fifo was 0 times empty and 11477 times full, min fill was 90%.
BURN-Free was 8 times used.
cdrecord command:
-----------------------
/usr/bin/cdrecord -v gracetime=2 dev=/dev/sr0 speed=16 -sao driveropts=burnfree -data -tsize=358320s -
Das Problem besteht übrigens sowohl mit cdrkit als auch mit den cdrtools ☹