ubuntuusers.de

Hallo Liebe User, ich habe ein Netbook eCafe und habe Ubuntu 9.04 installiert. Leider wird mir die benötigte Auflösung die ich bräuchte nicht angeboten. Jetzt ist es so, dass ich den unteren Teil des Deskopts nicht sehe. Wie kann ich da noch was ändern?

Ich habe 3 Auflösungen zur Verfügung die aber alle nicht passen...!!!

doob81

Hallo doob81,

du kannst Fenster mit gedrückter ALT-Taste verschieben, um auf nicht mehr sichtbare Schaltflächen zuzugreifen.

Um deine Auflösungsprobleme lösen zu können, wären ein paar weiter Angaben hilfreich. Welche native Auflösung hat der Bildschirm. Hänge bitte außerdem die Dateien "/etc/X11/xorg.conf" und "/var/log/Xorg.0.log" hier an.

nach den Daten muss ich kucken. Die Auflösung:

Hercules eCAFE EC-800-H20G/S Linux

AMD Geode LX 800 / 500 MHz - RAM 512 MB - Festplatte 20 GB - WLAN : 802.11 b/g - LAN - Linux - 8" (20.3 cm) Breitbildschirm LED TFT 800 x 480 - Cardreader (SD/SDHC/MMC/MS) - 4 Zellen Akku - Kamera

lg doob

Häng bitte noch die beiden Dateien an.

xorg.conf:

# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# Note that some configuration settings that could be done previously
# in this file, now are automatically configured by the server and settings
# here are ignored.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
#   sudo dpkg-reconfigure -phigh xserver-xorg

Section "Device"
	Identifier	"Configured Video Device"
EndSection

Section "Monitor"
	Identifier	"Configured Monitor"
EndSection

Section "Screen"
	Identifier	"Default Screen"
	Monitor		"Configured Monitor"
	Device		"Configured Video Device"
EndSection

xorg0.log:

X.Org X Server 1.6.0
Release Date: 2009-2-25
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-23-server i686 Ubuntu
Current Operating System: Linux marina-laptop 2.6.28-15-generic #49-Ubuntu SMP Tue Aug 18 18:40:08 UTC 2009 i586
Build Date: 09 April 2009  02:10:02AM
xorg-server 2:1.6.0-0ubuntu14 (buildd@rothera.buildd) 
	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Sep 28 13:11:39 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) No Layout section.  Using the first Screen section.
(**) |-->Screen "Default Screen" (0)
(**) |   |-->Monitor "Configured Monitor"
(**) |   |-->Device "Configured Video Device"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
	Entry deleted from font path.
(==) FontPath set to:
	/usr/share/fonts/X11/misc,
	/usr/share/fonts/X11/100dpi/:unscaled,
	/usr/share/fonts/X11/75dpi/:unscaled,
	/usr/share/fonts/X11/Type1,
	/usr/share/fonts/X11/100dpi,
	/usr/share/fonts/X11/75dpi,
	/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType,
	built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
	If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(II) Loader magic: 0x3bc0
(II) Module ABI versions:
	X.Org ANSI C Emulation: 0.4
	X.Org Video Driver: 5.0
	X.Org XInput driver : 4.0
	X.Org Server Extension : 2.0
(II) Loader running on linux
(++) using VT number 7

(--) PCI:*(0@0:1:1) Advanced Micro Devices [AMD] Geode LX Video rev 0, Mem @ 0x90000000/33554432, 0x8fffc000/16384, 0x8fff8000/16384, 0x8fff4000/16384, 0x8fff0000/16384
(II) Open ACPI successful (/var/run/acpid.socket)
(II) System resource ranges:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[5] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.13.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) Scanning /usr/share/xserver-xorg/pci directory for additional PCI ID's supported by the drivers
(II) Matched geode from file name geode.ids
(==) Matched geode for the autoconfigured driver
(==) Assigned the driver to the xf86ConfigLayout
(II) LoadModule: "geode"
(II) Loading /usr/lib/xorg/modules/drivers//geode_drv.so
(II) Module geode: vendor="X.Org Foundation"
	compiled for 1.5.99.902, module version = 2.11.1
	Module class: X.Org Video Driver
	ABI class: X.Org Video Driver, version 5.0
(II) GEODE: Driver for AMD Geode Chipsets: Geode LX, Geode GX
(II) Primary Device is: PCI 00@00:01:1
AmdPciProbe: Probing for supported devices!
(II) resource ranges after xf86ClaimFixedResources() call:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[5] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
(II) resource ranges after probing:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] 0	0	0x000a0000 - 0x000affff (0x10000) MS[B]
	[5] 0	0	0x000b0000 - 0x000b7fff (0x8000) MS[B]
	[6] 0	0	0x000b8000 - 0x000bffff (0x8000) MS[B]
	[7] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[8] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[9] 0	0	0x000003b0 - 0x000003bb (0xc) IS[B]
	[10] 0	0	0x000003c0 - 0x000003df (0x20) IS[B]
(WW) System lacks support for changing MTRRs
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 0.1.0
	ABI class: X.Org Video Driver, version 5.0
Unable to open /dev/cpu/0/msr: 2
(II) GEODE(0): Creating default Display subsection in Screen section
	"Default Screen" for depth/fbbpp 16/16
(==) GEODE(0): Depth 16, (==) framebuffer bpp 16
(==) GEODE(0): RGB weight 565
(==) GEODE(0): Default visual is TrueColor
(==) GEODE(0): Using gamma correction (1.0, 1.0, 1.0)
(==) GEODE(0): No DCON is present
(II) GEODE(0): LX output options:
(II) GEODE(0):  CRT: YES
(II) GEODE(0):  PANEL: YES
(II) GEODE(0):  DCON: NO
(II) GEODE(0):  VGA: YES
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	ABI class: X.Org Video Driver, version 5.0
(II) GEODE(0): Primary V_BIOS segment is: 0xc000
(II) GEODE(0): Output default using monitor section Configured Monitor
(II) GEODE(0): I2C bus "CS5536 DDC" initialized.
(II) GEODE(0): Output default connected
(II) GEODE(0): Using fuzzy aspect match for initial modes
(II) GEODE(0): Output default using initial mode 800x600
(--) GEODE(0): Virtual size is 800x800 (pitch 0)
(**) GEODE(0):  Driver mode "800x600": 40.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.3 Hz
(II) GEODE(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 -hsync -vsync (37.9 kHz)
(**) GEODE(0):  Default mode "800x600": 40.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.3 Hz
(II) GEODE(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(**) GEODE(0):  Default mode "640x480": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 59.9 Hz
(II) GEODE(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(**) GEODE(0):  Default mode "400x300": 20.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.3 Hz (D)
(II) GEODE(0): Modeline "400x300"x60.3   20.00  400 420 484 528  300 300 302 314 doublescan +hsync +vsync (37.9 kHz)
(**) GEODE(0):  Default mode "320x240": 12.6 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.1 Hz (D)
(II) GEODE(0): Modeline "320x240"x60.1   12.59  320 328 376 400  240 245 246 262 doublescan -hsync -vsync (31.5 kHz)
(==) GEODE(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "exa"
(II) LoadModule: "exa"
(II) Loading /usr/lib/xorg/modules//libexa.so
(II) Module exa: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 2.4.0
	ABI class: X.Org Video Driver, version 5.0
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] 0	0	0x000a0000 - 0x000affff (0x10000) MS[B]
	[5] 0	0	0x000b0000 - 0x000b7fff (0x8000) MS[B]
	[6] 0	0	0x000b8000 - 0x000bffff (0x8000) MS[B]
	[7] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[8] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[9] 0	0	0x000003b0 - 0x000003bb (0xc) IS[B]
	[10] 0	0	0x000003c0 - 0x000003df (0x20) IS[B]
(II) GEODE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) GEODE(0): Geode LX video memory 1600000 bytes at 0xb5e61000
(II) GEODE(0): LX video memory:
(II) GEODE(0):  Display: 0x190000 bytes
(II) GEODE(0):  Compression: 0x6a400 bytes
(II) GEODE(0):  Cursor: 0x3000 bytes
(II) GEODE(0):  EXA: 0xf8a400 bytes
(II) GEODE(0):  FREE: 0x338800 bytes
(II) EXA(0): Offscreen pixmap area of 16294912 bytes
(II) EXA(0): Driver registered support for the following operations:
(II)         Solid
(II)         Copy
(II)         Composite (RENDER acceleration)
(==) GEODE(0): Backing store disabled
(II) GEODE(0): DPMS enabled
(II) GEODE(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
(II) AIGLX: Screen 0 is not DRI capable
(II) AIGLX: Loaded and initialized /usr/lib/dri/swrast_dri.so
(II) GLX: Initialized DRISWRAST GL provider for screen 0
(II) GEODE(0): Setting screen physical size to 211 x 158
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 2.1.1
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 4.0
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event3"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) AT Translated Set 2 keyboard: xkb_rules: "evdev"
(**) Option "xkb_model" "pc105"
(**) AT Translated Set 2 keyboard: xkb_model: "pc105"
(**) Option "xkb_layout" "de"
(**) AT Translated Set 2 keyboard: xkb_layout: "de"
(II) config/hal: Adding input device Macintosh mouse button emulation
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event2"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) config/hal: Adding input device PS/2 Generic Mouse
(**) PS/2 Generic Mouse: always reports core events
(**) PS/2 Generic Mouse: Device: "/dev/input/event6"
(II) PS/2 Generic Mouse: Found 3 mouse buttons
(II) PS/2 Generic Mouse: Found x and y relative axes
(II) PS/2 Generic Mouse: Configuring as mouse
(**) PS/2 Generic Mouse: YAxisMapping: buttons 4 and 5
(**) PS/2 Generic Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "PS/2 Generic Mouse" (type: MOUSE)
(**) PS/2 Generic Mouse: (accel) keeping acceleration scheme 1
(**) PS/2 Generic Mouse: (accel) filter chain progression: 2.00
(**) PS/2 Generic Mouse: (accel) filter stage 0: 20.00 ms
(**) PS/2 Generic Mouse: (accel) set acceleration profile 0

niemand der mir weiterhelfen kann?

Ich habe mit Geode Chips bisher noch keine Erfahrung, du bist der erste der mir damit über den Weg läuft. Die bei dir konfigurierte Bildschirmauflösung müsste momentan 800x600 sein. Kannst du bitte mal die Ausgabe von folgendem Befehl posten: xrandr

Als Auflösung deines Bildschirms gibts du 800x480 an, das ist dann auch die Auflösung die du einstellen möchtest?

Hallo,

ich habe dasselbe Netbook wie doob81, ein Hercules EC-800 eCafe. Zur Hardware sagt lscpi übrigens folgendes:

00:01.0 Host bridge: Advanced Micro Devices [AMD] CS5536 [Geode companion] Host Bridge (rev 33)
00:01.1 VGA compatible controller: Advanced Micro Devices [AMD] Geode LX Video
00:01.2 Entertainment encryption device: Advanced Micro Devices [AMD] Geode LX AES Security Block
00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:0f.0 ISA bridge: Advanced Micro Devices [AMD] CS5536 [Geode companion] ISA (rev 03)
00:0f.2 IDE interface: Advanced Micro Devices [AMD] CS5536 [Geode companion] IDE (rev 01)
00:0f.3 Multimedia audio controller: Advanced Micro Devices [AMD] CS5536 [Geode companion] Audio (rev 01)
00:0f.4 USB Controller: Advanced Micro Devices [AMD] CS5536 [Geode companion] OHC (rev 02)
00:0f.5 USB Controller: Advanced Micro Devices [AMD] CS5536 [Geode companion] EHC (rev 02)

Ich habe Xubuntu 9.10 Karmic Koala installiert und dasselbe Problem mit der Auflösung der Geode-LX-Grafikkarte. Xubuntu liefert 800x600, der kleine Bildschirm kann aber wohl nur 800x400. Das steht im Xorg.0.log:

Xorg.0.log

Eine xorg.conf gibt es in Karmic nicht mehr. Und xandr gibt folgendes aus:

Screen 0: minimum 320 x 200, current 800 x 600, maximum 800 x 800
default connected 800x600+0+0 (normal left inverted right x axis y axis) 0mm x 0mm
   800x600        60.3*    60.3  
   640x480        59.9  
   400x300       120.6  
   320x240       120.1  

Viele Grüße

Christian

Probiert bitte mal aus die Farbtiefe auf 16bit zu setzen → xorg.conf

Also die Farbtiefe ist bei mir schon auf 16 Bit:

$ sudo grep bpp /var/log/Xorg.0.log
	"Builtin Default geode Screen 0" for depth/fbbpp 16/16
(==) GEODE(0): Depth 16, (==) framebuffer bpp 16

Probiers doch mal damit. Hat bei mir Prima funktioniert 😀

http://forum.ubuntuusers.de/post/2354365/

Vieleicht gehts ja?